Manual
Table Of Contents
- 1. General
- 1.1 About this document
- 1.2 Warranty
- 1.3 Limitation of liability
- 1.4 Disposal of equipment
- 1.5 Product key
- 1.6 Intended usage
- 1.7 Safety
- 1.8 Technical Data
- 1.9 Construction and function
- 1.9.1 General description
- 1.9.2 Block diagram
- 1.9.3 Scope of delivery
- 1.9.4 Accessories
- 1.9.5 Options
- 1.9.6 The control panel (HMI)
- 1.9.7 USB port (rear side)
- 1.9.8 Interface module slot
- 1.9.9 Analog interface
- 1.9.10 “Share BUS” connector
- 1.9.11 “Sense” connector (remote sensing)
- 1.9.12 Master-Slave bus
- 1.9.13 Ethernet port
- 2. Installation & commissioning
- 2.1 Transport and storage
- 2.2 Unpacking and visual check
- 2.3 Installation
- 2.3.1 Safety procedures before installation and use
- 2.3.2 Preparation
- 2.3.3 Installing the device
- 2.3.4 Connection to AC supply
- 2.3.5 Connection to DC sources
- 2.3.6 Connection of remote sensing
- 2.3.7 Grounding of the DC terminal
- 2.3.8 Installation of an interface module
- 2.3.9 Connection of the analog interface
- 2.3.10 Connection of the Share bus
- 2.3.11 Connection of the USB port (rear side)
- 2.3.12 Initial commission
- 2.3.13 Commission after a firmware update or a long period of non-use
- 3. Operation and application
- 3.1 Important notes
- 3.2 Operating modes
- 3.3 Alarm conditions
- 3.4 Manual operation
- 3.5 Remote control
- 3.6 Alarms and monitoring
- 3.7 Locking the control panel (HMI)
- 3.8 Locking the adjustment limits and user profiles
- 3.9 Loading and saving user profiles
- 3.10 The function generator
- 3.10.1 Introduction
- 3.10.2 General
- 3.10.3 Method of operation
- 3.10.4 Manual operation
- 3.10.5 Sine wave function
- 3.10.6 Triangular function
- 3.10.7 Rectangular function
- 3.10.8 Trapezoidal function
- 3.10.9 DIN 40839 function
- 3.10.10 Arbitrary function
- 3.10.11 Ramp function
- 3.10.12 IU table function (XY table)
- 3.10.13 Battery test function
- 3.10.14 MPP tracking function
- 3.10.15 Remote control of the function generator
- 3.11 Other applications
- 4. Service and maintenance
- 5. Contact and support
© EA Elektro-Automatik in 2022, this information is subject to change without notice 1533200840_manual_elr_10000_2u_3kw_en_02
Technical speci cations ELR 10080-120 ELR 10200-50 ELR 10360-30 ELR 10500-20 ELR 10750-12
DC input
Voltage range 0 - 80 V 0 -200 V 0 - 360 V 0 - 500 V 0 - 750 V
U
Min
for I
Max
0.8 V 2 V 2 V 2.5 V 2.5 V
Current range 0 - 120 A 0 - 50 A 0 - 30 A 0 - 20 A 0 - 12 A
Power range
*1 0 - 3000 W (0 - 1500 W) 0 - 3000 W (0 - 1500 W) 0 - 3000 W (0 - 1500 W) 0 - 3000 W (0 - 1500 W) 0 - 3000 W (0 - 1500 W)
Resistance range 0.02 Ω - 40 Ω 0.1 Ω - 250 Ω 0.4 Ω -800 Ω 1 Ω - 1500 Ω 2 Ω - 3000 Ω
Output capacity 17280 μF 1600 μF 660 μF 240 μF 80 μF
Effi ciency ≤94%
*2 ≤94.5% *2 ≤94.5% *2 ≤95% *2 ≤95% *2
Insulation
Negative DC pole <-> PE ±600 V DC ±1000 V DC ±1000 V DC ±1500 V DC ±1500 V DC
Positive DC pole <-> PE +600 V DC +1000 V DC +1000 V DC +2000 V DC +2000 V DC
Article number 33200845 33200846 33200847 33200848 33200849
Technical speci cations ELR 11000-10 ELR 11500-06
DC input
Voltage range 0 - 1000 V 0 - 1500 V
U
Min
for I
Max
4 V 4.2 V
Current range 0 - 10 A 0 - 6 A
Power range
*1 0 - 3000 W (0 - 1500 W) 0 - 3000 W (0 - 1500 W)
Resistance range 3 Ω - 6000 Ω 8 Ω -6000 Ω
Output capacity 60 μF 20 μF
Effi ciency ≤95%
*2 ≤95% *2
Insulation
Negative DC pole <-> PE ±1500 V DC ±1500 V DC
Positive DC pole <-> PE +2000 V DC +2000 V DC
Article number 33200850 33200851
*1 The value in brackets applies to the state of derating (power reduction) for 110 to 127 V ±10% utility
*2 At 100% power and 100% input voltage
*1 The value in brackets applies to the state of derating (power reduction) for 110 to 127 V ±10% utility
*2 At 100% power and 100% input voltage