User manual

Page 3
EA Elektro-Automatik GmbH
Helmholtzstr. 31-37 • 41747 Viersen
Germany
Fon: +49 2162 / 3785-0
Fax: +49 2162 / 16230
www.elektroautomatik.de
[e-mail]
EL 9000 B HP Series
TABLE OF CONTENTS
1
GENERAL
1.1 About this document ......................................5
1.1.1 Retention and use ..........................................5
1.1.2 Copyright ........................................................5
1.1.3 Validity ............................................................5
1.1.4 Symbols and warnings ..................................5
1.2 Warranty ......................................................... 5
1.3 Limit of liability ................................................5
1.4 Disposal of equipment ...................................6
1.5 Product key ....................................................6
1.6 Intended usage ..............................................6
1.7 Safety .............................................................7
1.7.1 Safety notices .................................................7
1.7.2 Responsibility of the user...............................7
1.7.3 Responsibility of the operator .......................8
1.7.4 User requirements .........................................8
1.7.5 Alarm signals ..................................................9
1.8 Technical data ................................................9
1.8.1 Approved operating conditions ......................9
1.8.2 General technical data ................................... 9
1.8.3 Specictechnicaldata .................................10
1.8.4 Views ............................................................14
1.8.5 Control elements .......................................... 17
1.9 Construction and function ............................ 18
1.9.1 General description ...................................... 18
1.9.2 Block diagram ..............................................18
1.9.3 Scope of delivery .........................................19
1.9.4 Accessories .................................................. 19
1.9.5 The control panel (HMI) ...............................20
1.9.6 USB-Port Type B (Back side) ......................23
1.9.7 Interface module slot ...................................23
1.9.8 Analog interface ...........................................23
1.9.9 “Share” connector ........................................24
1.9.10 “Sense” connector (remote sensing) ...........24
1.9.11 Master-Slave bus .........................................24
2
INSTALLATION & COMMISSIONING
2.1 Transport and storage .................................25
2.1.1 Transport ......................................................25
2.1.2 Packaging ....................................................25
2.1.3 Storage ......................................................... 25
2.2 Unpacking and visual check ........................ 25
2.3 Installation ....................................................25
2.3.1 Safety procedures before installation and
use ................................................................25
2.3.2 Preparation ................................................... 26
2.3.3 Installing the device .....................................26
2.3.4 Connection to DC sources ..........................27
2.3.5 Grounding of the DC input ........................... 28
2.3.6 Connecting the “Share” bus ........................28
2.3.7 Connection of remote sensing ....................28
2.3.8 Connecting the USB port (rear side) ...........29
2.3.9 Installation of an interface module ...............29
2.3.10 Connecting the analog interface .................30
2.3.11 Initial commission ......................................... 30
2.3.12 Commissionafterarmwareupdateora
long period of non use .................................30
3
OPERATION AND APPLICATION
3.1 Personal safety ............................................31
3.2 Operating modes .........................................31
3.2.1 Voltage regulation / Constant voltage .........31
3.2.2 Current regulation / constant current / current
limitation .......................................................32
3.2.3 Resistance regulation / constant resistance 32
3.2.4 Power regulation / constant power / power
limitation .......................................................32
3.2.5 Dynamic characteristics and stability crite-
ria .................................................................. 33
3.3 Alarm conditions ..........................................34
3.3.1 Power Fail ...................................................34
3.3.2 Overtemperature .......................................... 34
3.3.3 Overvoltage .................................................. 34
3.3.4 Overcurrent ..................................................34
3.3.5 Overpower ....................................................34
3.4 Manual operation .........................................35
3.4.1 Powering the device ....................................35
3.4.2 Switching the device off ...............................35
3.4.3 CongurationviaMENU ..............................35
3.4.4 Adjustment limits ..........................................45
3.4.5 Changing the operating mode ..................... 45
3.4.6 Manual adjustment of set values .................46
3.4.7 Switching the main screen view ..................46
3.4.8 The meter bars ............................................. 47
3.4.9 Switching the DC input on or off ..................47
3.4.10 Recording to USB stick (logging) ................48
3.5 Remote control ............................................. 49
3.5.1 General .........................................................49
3.5.2 Controls locations ........................................49
3.5.3 Remote control via a digital interface ..........49
3.5.4 Remote control via the analog interface
(AI) ................................................................50
3.6 Alarms and monitoring ................................. 54
3.6.1 Denitionofterms ........................................54
3.6.2 Device alarm and event handling ................ 54
3.7 Control panel (HMI) lock ..............................57
3.8 Limits lock .....................................................57
3.9 Loadingandsavingauserprole ...............58
3.10 The function generator.................................59
3.10.1 Introduction...................................................59
3.10.2 General .........................................................59
3.10.3 Method of operation ..................................... 59
3.10.4 Manual operation .........................................60
3.10.5 Sine wave function ....................................... 61
3.10.6 Triangular function .......................................61