User manual
Table Of Contents
- 1. Allgemeines
- 2. Technische Daten
- 3. Installation
- 4. Details zu den Kartentypen
- 4.1 RS232-Karten IF-R1 und IF-R2
- 4.2 USB-Karten IF-U1 und IF-U2
- 4.3 CAN-Karten IF-C1 und IF-C2
- 4.4 Analoge Schnittstelle IF-A1
- 4.5 GPIB-Karte IF-G1
- 4.5.1 Hinweise zur Kommunikation
- 4.5.2 Ansteuerung des Gerätes über GPIB
- 4.5.3 Begriffserläuterung
- 4.5.4 Unterschiede zu den anderen Schnittstellenkarten
- 4.5.5 Firmware-Aktualisierungen
- 4.5.6 Ausführungs- und Übertragungszeiten
- 4.5.7 IF-G1 konfigurieren
- 4.5.8 SCPI-Befehle und Abschlußzeichen
- 4.5.9 Fehlermeldungen
- 4.6 Ethernetkarten IF-E1 und IF-E2
- 5. Einsatz in anderen Geräteserien
- 6. Der System Link Mode (nur PSI 9000)
- 7. Kommunikation mit dem Gerät
- 7.1 Begriffserklärungen
- 7.2 Vorwort
- 7.3 Allgemeine Hinweise zur Kommunikation
- 7.4 Hinweise zum USB-Treiber
- 7.5 Aufbau der Kommunikation
- 7.6 Übertragungsparameter IF-R1 und IF-U1
- 7.7 Sollwerte und Istwerte umrechnen
- 7.8 Telegrammaufbau IF-R1 und IF-U1
- 7.9 Telegrammaufbau IF-C1
- 7.10 Telegrammaufbau IF-G1
- 7.11 Telegrammaufbau IF-E1
- 8. Kommunikation mit LabView
- 9. Kommunikation ohne Labview
- 10. Anschlüsse
- 1. General
- 2. Technical specifications
- 3. Installation
- 4. Details about the cards
- 5. Operation in other device series
- 6. The System Link Mode (only PSI9000)
- 7. Communication with the device
- 7.1 Terms explained
- 7.2 Prologue
- 7.3 General notes about the communication
- 7.4 About the USB driver
- 7.5 Structure of the communication
- 7.6 Transmission settings IF-R1 and IF-U1
- 7.7 Translating set/actual values
- 7.8 Telegram structure IF-R1 and IF-U1
- 7.9 Message structure for the IF-C1
- 7.10 Message structure IF-G1
- 7.11 Message structure IF-E1
- 8. Communication with LabView
- 9. Communication without LabView
- 10. Connectors
77
© 2009, Elektro-Automatik GmbH & Co. KG
EN
About the interface cards
5. Operation in other device series
5.1 Electronic loads EL 3000 / EL 9000
The electronic loads of the series EL3000 and EL9000 sup-
port the following interface cards:
IF-U1, IF-R1, IF-C1, IF-G1
Note about the GPIB card IF-G1: at devices with firmware
version 2.11 or older the card is detected as IF-C1 (CAN
card) and must be configured to following settings:
- CAN Baudrate: 100kBd
- Bus termination: no
- Relocatable ID: 0
Also, in devices with firmware version 2.14 or lower, the
card is not correctly supported. We recommend an update.
Please contact your dealer.
At firmware version 3.01 or higher there are no limitations.
The general functionality of the interface cards is the same
if used in a power supply. The amount of features is limited,
but also different.
Please refer to the previous sections for detailed information
about the interface cards.
You can configure the interface cards in the setup menu of
the devices. This is activated by turning the switch Level
Control to position Setup.
Depending on which card is equipped (the electronic loads
feature only one card slot) a different selection of parameters
is available. The parameters and their values are identical to
the ones explained in section 4.1 to 4.3, with the exception
that no Sample point can be set at CAN.
There are also no settable parameters for the USB and
IEEE cards.
5.2 Series PS 8000 T/ DT / 2U
Access to the device setup via pushbutton Fine (press >2s
while output is „off“), for details of settings see user manual of
the device. The GPIB and USB cards are not configured.
5.3 Series PSI 800 R
The shortened type 2 cards are used here. Setup and c
configuration are explained in the user manual of the device
and also in section 4 (menu structure and handling of PSI
800 R series is similiar to PSI 9000 series).
Card found: IF-C1
CAN Baudrate: 10kBd
Card found: IF-C1
CAN Relocatable ID: 13
Card found: IF-C1
CAN Bus terminate: yes
Card found: IF-R1
RS232 Baudrate: 9600Bd
EL 3000/9000 Menu example of the CAN card:
EL 3000/9000 Menu example RS232 card: