User manual
Table Of Contents
- 1. Allgemeines
- 2. Technische Daten
- 3. Installation
- 4. Details zu den Kartentypen
- 4.1 RS232-Karten IF-R1 und IF-R2
- 4.2 USB-Karten IF-U1 und IF-U2
- 4.3 CAN-Karten IF-C1 und IF-C2
- 4.4 Analoge Schnittstelle IF-A1
- 4.5 GPIB-Karte IF-G1
- 4.5.1 Hinweise zur Kommunikation
- 4.5.2 Ansteuerung des Gerätes über GPIB
- 4.5.3 Begriffserläuterung
- 4.5.4 Unterschiede zu den anderen Schnittstellenkarten
- 4.5.5 Firmware-Aktualisierungen
- 4.5.6 Ausführungs- und Übertragungszeiten
- 4.5.7 IF-G1 konfigurieren
- 4.5.8 SCPI-Befehle und Abschlußzeichen
- 4.5.9 Fehlermeldungen
- 4.6 Ethernetkarten IF-E1 und IF-E2
- 5. Einsatz in anderen Geräteserien
- 6. Der System Link Mode (nur PSI 9000)
- 7. Kommunikation mit dem Gerät
- 7.1 Begriffserklärungen
- 7.2 Vorwort
- 7.3 Allgemeine Hinweise zur Kommunikation
- 7.4 Hinweise zum USB-Treiber
- 7.5 Aufbau der Kommunikation
- 7.6 Übertragungsparameter IF-R1 und IF-U1
- 7.7 Sollwerte und Istwerte umrechnen
- 7.8 Telegrammaufbau IF-R1 und IF-U1
- 7.9 Telegrammaufbau IF-C1
- 7.10 Telegrammaufbau IF-G1
- 7.11 Telegrammaufbau IF-E1
- 8. Kommunikation mit LabView
- 9. Kommunikation ohne Labview
- 10. Anschlüsse
- 1. General
- 2. Technical specifications
- 3. Installation
- 4. Details about the cards
- 5. Operation in other device series
- 6. The System Link Mode (only PSI9000)
- 7. Communication with the device
- 7.1 Terms explained
- 7.2 Prologue
- 7.3 General notes about the communication
- 7.4 About the USB driver
- 7.5 Structure of the communication
- 7.6 Transmission settings IF-R1 and IF-U1
- 7.7 Translating set/actual values
- 7.8 Telegram structure IF-R1 and IF-U1
- 7.9 Message structure for the IF-C1
- 7.10 Message structure IF-G1
- 7.11 Message structure IF-E1
- 8. Communication with LabView
- 9. Communication without LabView
- 10. Connectors
52
© 2009, Elektro-Automatik GmbH & Co. KG
EN
Important!
• Only equip the interface card(s) in units which are designed
to be used with them! It is not required to open the unit.
Information about which devices are capable of running
these interface cards can be requested from your local
dealer or read in the user manual of the devices.
• Only equip the interface card(s) while the unit is switched
off by the mains switch!
• Units featuring two slots might be equipped with two cards,
but you can’t combine them arbitrarily. For detailed infor-
mation see section „3.3 Combination of interface cards“
• Never remove the covers from the cards!
• If only one card is equipped in units with two slots it is
recommended to install the default slot cover to the open
slot. This protects the unit from additional dust pollution and
ensures correct air circulation with the internal fans.
• Use and follow the common ESD provisions when installing
and removing the interface cards!
About & Copyright
User manual for interface cards
Elektro-Automatik GmbH & Co. KG
Helmholtzstrasse 31-33
41747 Viersen
Germany
Phone: +49 (0)2162 / 37850
Fax: +49 (0)2162 / 16230
Web: www.elektroautomatik.de
Mail: ea1974@elektroautomatik.de
© 2009 Elektro-Automatik
Reprint, duplication or partly, wrong use of this user ma-
nual are prohibited and might be followed by legal conse-
quences.
Date: June, 2009