Datasheet

Irrtümer und Änderungen vorbehalten / Subject to modication without notice, errors and omissions excepted
© EA-Elektro-Automatik GmbH, 2012, Last change: 18.11.13
EA-PSI 8000 3U 3.3KW - 150KW
HOCHLEISTUNGS-DC-LABORNETZGERÄTE / HIGH EFFICIENCY LABORATORY DC POWER SUPPLIES
Leistung
Die Geräte haben eine exible, leistungsgeregelte
Ausgangsstufe die bei hoher Ausgangsspannung den
Strom oder bei hohem Ausgangsstrom die Spannung
so reduziert, daß die maximale Ausgangsleistung nicht
überschritten wird. So kann mit nur einem Gerät ein
breites Anwendungsspektrum abgedeckt werden.
Eingang
Die Geräte besitzen alle eine aktive Leistungsfaktorkorrektur
(PFC) und sind für den Einsatz an einem Drehstromnetz mit
340V bis 460V AC ausgelegt. Alternativ können Geräte mit
15kW oder daraus kombinierte Systeme mit Stern-Eingang für
588...796V AC plus MP geliefert werden.
Ausgang
Zur Verfügung stehen Geräte mit Ausgangsspannungen von
0...40V bis 0...1500V, Strömen von 0...40A bis 0...510A und von
0...100% regelbaren Leistungen zwischen 3,3kW und 15kW.
Der Ausgang bendet sich auf der Rückseite der Geräte.
Überspannungsschutz (OVP)
Um die angeschlossenen Verbraucher vor Zerstörung zu schüt-
zen kann ein Überspannungsschutz (OVP) eingestellt werden.
Beim Überschreiten des eingestellten Wertes wird der Ausgang
abgeschaltet und es wird eine Warnmeldung als akustisches
Signal und als Statusmeldung auf der analogen Schnittstelle
und im Display ausgegeben.
Alarmmanagement
Um die Ausgangsspannung und den Ausgangsstrom zu über-
wachen, kann ein Arbeitsbereich mit Unter- und Obergrenzen
deniert werden. Dem Anwender stehen mehrere Möglichkeiten
zur Auswahl, wie das Netzgerät beim Verlassen dieses Arbeits-
bereichs reagieren soll. Eine Meldung wirkt sich nicht auf den
Ausgang aus und wird, so lange sie ansteht, auf dem Display
angezeigt. Warnungen bleiben hingegen auch dann bestehen,
wenn die Werte wieder im normalen Bereich sind. Sie müssen
dann vom Anwender quittiert werden. Alarme schalten den Aus-
gang direkt ab, wenn ein Wert überschritten wird. Warnungen
und Alarme können akustisch signalisiert werden.
Fernfühlung (Sense)
Der serienmäßig vorhandene Fernfühlungseingang (Sense)
kann direkt am Verbraucher angeschlossen werden, um den
Spannungsabfall auf den Lastleitungen zu kompensieren.
Das Gerät erkennt selbstständig wenn die Senseleitungen
angeschlossen sind und regelt die Ausgangsspannung direkt
am Verbraucher.
Anzeige- und Bedienelemente
Das leicht abzulesende Grakdisplay bietet zu jeder Zeit eine
übersichtliche Darstellung der eingestellten Werte, der aktuellen
Ausgangsdaten und des Betriebzustandes.
Für alle benötigten Informationen und Ein-
stellungen wird der Anwender durch ein
übersichtliches Menü geführt.
Istwerte und Sollwerte von Ausgangsspan-
nung, Strom und Leistung, und optional
Widerstand, werden auf dem Grakdisplay
übersichtlich dargestellt. Die Betriebszu-
stände des Gerätes, die Menüführung und
die momentane Belegung der Folientastatur
werden im Display so angezeigt, daß es dem
Anwender möglich ist das Gerät intuitiv zu
bedienen.
Power
All units are equipped with a exible autoranging
output stage which provides a higher output voltage
at lower output current, or a higher output current at
lower output voltage, always limited to the maximum
nominal output power. Therefore, a wide range of
applications can already be covered by the use of
just one single unit.
Input
The device are equipped with an active Power Factor Correction
circuit and are designed for a usage on a three-phase supply
with 340V - 460V AC. Alternatively, models with 15kW or cabi-
nets based on these models can be delivered with input range
588...796V AC (plus central point) upon request.
Output
Output voltages between 0...40V and 0...1500V, output currents
between 0...40A and 0...510A and fully adjustable output power
ratings between 3.3kW and 15kW are available. The output
terminal is located in the rear panel.
Overvoltage protection (OVP)
Intended to protect connected loads, it is possible to dene an
overvoltage protection limit (OVP).
If the output voltage exceeds the dened limit, the output is
shut-off and an acoustic warning signal will be given by the unit
and also a status message signal in the display is available.
Alarm management
For monitoring the correct output voltage and output current,
lower and upper limits can be dened.
If the deviation exceeds the adjusted limits, three possibilities
are available as to how the appliance should react.
- Signals are displayed only; even if the fault is still active, wi-
thout affecting the output
- Warnings remain active and must be acknowledged after the
fault is removed
- Alarms will shut off the output instantly in case the deviation
exceed the adjusted limits.
Alarms and Warnings can be signalled acoustically.
Remote sense
The standard sense input can be connected directly to the load
in order to compensate voltage drops along the power cables.
If the sense input is connected to the load, the power supply will
be adjusting the output voltage automatically to make ensure
the accurate required voltage is available at the load.
Display and controls
The easily readable graphic display shows a clear represen-
tation of set values, actual output values, the operational state
and the current functions of the operation
pushbuttons.
For all necessary information and adjust-
ments the user is guided by a clear menu.
Set values and actual values of output
voltage, output current and output power
are clearly represented on the graphic dis-
play. The operating state of the device, the
menu guidance and the current assignment
of the pushbuttons are also shown on the
display. So the user is able to operate the
unit intuitively.