User manual

Page 3
EA Elektro-Automatik GmbH
Helmholtzstr. 31-33 • 41747 Viersen
Germany
Fon: +49 2162 / 3785-0
Fax: +49 2162 / 16230
www.elektroautomatik.de
[e-mail]
PSI 9000 2U Series
TABLE OF CONTENTS
1
GENERAL
1.1 About this document ......................................5
1.1.1 Retention and use ..........................................5
1.1.2 Copyright ........................................................5
1.1.3 Validity ............................................................5
1.1.4 Symbols and warnings ..................................5
1.2 Warranty ......................................................... 5
1.3 Limitation of liability ........................................5
1.4 Disposal of equipment ...................................6
1.5 Product key ....................................................6
1.6 Intended usage ..............................................6
1.7 Safety .............................................................7
1.7.1 Safety notices .................................................7
1.7.2 Responsibility of the user...............................7
1.7.3 Responsibility of the operator .......................8
1.7.4 User requirements .........................................8
1.7.5 Alarm signals ..................................................9
1.8 Technical Data ...............................................9
1.8.1 Approved operating conditions ......................9
1.8.2 General technical data ................................... 9
1.8.3 Specic technical data .................................10
1.8.4 Views ............................................................22
1.9 Construction and function ............................ 26
1.9.1 General description ...................................... 26
1.9.2 Block diagram ..............................................26
1.9.3 Scope of delivery .........................................27
1.9.4 Accessories .................................................. 27
1.9.5 Options .........................................................27
1.9.6 The control panel (HMI) ...............................28
1.9.7 USB port (rear side) .....................................31
1.9.8 Interface module slot ...................................31
1.9.9 Analog interface ...........................................31
1.9.10 Share Bus-Connection ................................32
1.9.11 Sense connector (remote sensing) .............32
1.9.12 Master-Slave bus .........................................32
1.9.13 GPIB port (optional) .....................................32
2
INSTALLATION & COMMISSIONING
2.1 Transport and storage .................................33
2.1.1 Transport ......................................................33
2.1.2 Packaging ....................................................33
2.1.3 Storage ......................................................... 33
2.2 Unpacking and visual check ........................ 33
2.3 Installation ....................................................33
2.3.1 Safety procedures before installation and
use ................................................................33
2.3.2 Preparation ................................................... 34
2.3.3 Installing the device .....................................34
2.3.4 Connection to AC supply .............................35
2.3.5 Connection to DC loads ...............................35
2.3.6 Grounding of the DC output ........................36
2.3.7 Connection of remote sensing ....................37
2.3.8 Installation of an AnyBus interface module .38
2.3.9 Connecting the analog interface .................38
2.3.10 Connecting the “Share” bus ........................39
2.3.11 Connecting the USB port (rear side) ...........39
2.3.12 Initial commission ......................................... 39
2.3.13 Commission after a rmware update or a
long period of non-use .................................39
3
OPERATION AND APPLICATION
3.1 Personal safety ............................................40
3.2 Operating modes .........................................40
3.2.1 Voltage regulation / Constant voltage .........40
3.2.2 Current regulation / constant current / current
limiting ..........................................................40
3.2.3 Power regulation / constant power / power
limiting ..........................................................41
3.2.4 Internal resistance regulation ......................41
3.3 Alarm conditions ..........................................42
3.3.1 Power Fail ...................................................42
3.3.2 Overtemperature .......................................... 42
3.3.3 Overvoltage protection.................................42
3.3.4 Overcurrent protection .................................42
3.3.5 Overpower protection ..................................42
3.4 Manual operation .........................................43
3.4.1 Switching on the device ...............................43
3.4.2 Switching off the device ...............................43
3.4.3 Conguration via MENU ..............................43
3.4.4 Adjustment limits (Limits) ............................. 51
3.4.5 Changing the operating mode ..................... 51
3.4.6 Manual adjustment of set values .................52
3.4.7 Switching the DC output on or off ................53
3.5 Remote control ............................................. 54
3.5.1 General .........................................................54
3.5.2 Control locations ..........................................54
3.5.3 Remote control via a digital interface ..........54
3.5.4 Remote control via the analog interface
(AI) ................................................................55
3.6 Alarms and monitoring ................................. 59
3.6.1 Denition of terms ........................................59
3.6.2 Device alarm and event handling ................ 59
3.7 Control panel (HMI) lock ..............................61
3.8 Loading and saving a user prole ...............61
3.9 The function generator.................................62
3.9.1 Introduction...................................................62
3.9.2 General .........................................................62
3.9.3 Method of operation ..................................... 62
3.9.4 Manual operation .........................................63
3.9.5 Sine wave function ....................................... 64
3.9.6 Triangular function .......................................64
3.9.7 Rectangular function .................................... 65
3.9.8 Trapezoidal function .....................................66
3.9.9 DIN 40839 function ......................................66