e.ziclean® e.
Welcome to E.
Summary 1. Introduction.....................................................................................4 2. Register your product.......................................................................... 4 3. Precautions of use.............................................................................. 4 4. Box content...................................................................................... 5 5. Name of e.ziclean FURTIV parts..............................................................
1. Introduction Thank you for the trust you have placed in our range of e.ziclean® robots. We are delighted to count you among our customers and are confident that you will enjoy the precious time that you will be saving using our vacuum cleaning robot. The e.ziclean® robots offer specific features and options that fit your expectations. To fease the use of your device, please read this user manual. Once you will get familiar with our products, e.
4. Box content e.
5. Name of e.ziclean FURTIV parts A. TOP OF THE ROBOT B. BOTTOM OF THE ROBOT 1. Front bumper 8. Ground detector sensor 15. UV sterilizing lamp 2. Infrared signal receiver 9. Battery cover 16. Left wheel 3. Auto-charging electrode 10. Side cleaning brush 17. Floor brush 4. Dustbin key 11. Ground detection sensor 18. Main brush 5. Display screen 12. Right wheel 19. Trailing bar 6. Sensor window 13. Power switch 20. Mop pad 7. Front wheel 14. DC socket 21. Dustbin 22.
5. Name of e.ziclean FURTIV parts C. DOCKING STATION 23. Swith ON of Decorative Light 25. Charging Power socket 27. Charging Indicator 24. Decorative Light 26. Power Led 28. IR Signal 29. Charging Connectors D. IR BARRIER 30. Main switch 32. 2 meters range 35. IR Signal 31. OFF position 33. 4 meters range 36. IR Emitter 34. 6 meters ranges 37.
5. Name of e.ziclean FURTIV parts E. REMOTE CONTROL 38. AUTO Cleaning Mode 39. Thursday . In Scheduling Mode 40. Time Setting 41. Tuesday . In Scheduling Mode 42. Mute 43. Scheduling Setting Monday . In Scheduling Mode 44. ON / OFF switch 45. Spot Cleaning Mode 46. Friday . In Scheduling Mode 48. Manual Control of the robot 49. Confirmation button 50. Saturday . In Scheduling Mode 51. Cleaning Speed Option 52. Back to Dock Station 53. Sunday . In Scheduling Mode 54. ON / OFF UV Lamp 55.
6. Installation and charging of your robot A. AUTO CHARGING OPTION Install the Docking Station on a flat ground, firmly and against the wall using its sticker. Make sure that no obstacle and uneven ground is in the area within 3 meters in front of the base and 0,5 meters respectively on the left and right of it: Ensure that IR Signal window from the base is clean without dust or something else covered. Otherwise the function of self-charging will be influenced.
• Make your robot get back to its charging station Press the ''DOCK'' button from the remote control. e.ziclean® FURTIV will start searching for its dock station. The charging status information are displayed as follow : • While charging, e.ziclean® FURTIV battery display will blink gradually. • Once fully charged, the battery display will stop blinking showing 3 full grades. Advises e.ziclean® may fail to find the docking station due to some obstacles.
7. Use of Remote Control A. E.ZICLEAN® FURTIV TIME SETTING-UP Turn your robot ON. Press the from the remote. the WEEK 8 display will blink. n Press the arrows to select the day. (WEEK 1 = Monday, WEEK 2 = Tuesday, WEEK 3 = Wednesday, WEEK 4 = Thursday, WEEK 5 = Friday, WEEK 6 = Saturday, WEEK 7 = Sunday). m Press from you remote to set the hour. n Press to select the hour and confirm with o Press to select the minutes. p Finally confirm your time setting-up pressing B.
C. CANCEL OR MODIFY YOUR WEEKLY SCHEDULE INFORMATION To unschedule a day from your weekly schedule or to disabled the FULL GO mode, press the button. Now simply press the button of the week you want to add or to remove. The number corresponding will disappear from the clock display. Other days of the week that were already schedule will be preserved. Proceed the same way if you want to disable the FULL GO option. Save your modifications pressing 8. Navigation functions of e.ziclean® FURTIV e.
9. Maintenance of your e.ziclean® FURTIV robot. In general, e.ziclean® vacuum robots require minimal maintenance. When cleaning particularly ingrained dust or animal hair areas, remember to clean your device after each use. And to continue to use you robot in the best performing conditions, here are some procedures to take into account: A. HOW TO CLEAN THE DUST BOX AND FILTERS Press the eject button of the dust box. Attention : Do not wash your dust box using water.
B. USAGE OF THE CLEANING MOP Attach the enclosed mopping rag to the mopping holder. Refer to the below scheme to lock the mopping kit to the robot. Once correctly installed, e.ziclean® FURTIV will optimized its cleaning efficiency especially on hard floors such as linoleum, tiles... After using, just pull the holder out. It’s recommended to wash and twist dry the mopping cloth before each use of the mopping function.
D. MAINTENANCE OF THE SIDE BRUSH Use a screw driver to remove the cleaning side brush from the robot. While out of use, replace your side brush for a new one. Advises It is possible to give back your side brush shape putting them into water for few minutes. E. CLEANING STAIR SENSORS AND INFRARED DETECTOR The sensors and infrared detector should be cleaned by using a cotton swab or soft cloth.
10. batteries Installation A. INSTALLATION OF IR BARRIERS BATTERIES The IR Barrier is powered by two 1.5V batteries. Simply unscrew the cover at the base of the IR Barrier and close it once the batteries are properly installed in accordance with the direction indicated on the bottom cover. B. INSTALLATION OF REMOTE CONTROL BATTERIES Simply insert two AAA batteries.
C. REPLACEMENT OF THE ROBOT BATTERY Unscrew the battery cover. Remove the battery and replace it by a new one Replace the cover screwing it. Your robot is ready to be used. D. MAINTENANCE AND SAFETY INSTRUCTIONS Remove batteries from your appliances if not used for a long time. Switch off your apliance while operating a battery change. Once batteries are out of used, through them into a trash provided for this purpose. 11. IR Barriers settings. A.
The IR Barrier accessory can be used to restrict the robot entering into a specific area. Once the robot gets close enough to the IR Barrier, it will automatically avoid crossing the non-visible IR line and continue cleaning the other areas. IR Barrier generally must be placed at the entrance of the room to be cleaned. It is also possible to place it on a spot where you do not want the robot vacuum cleaner to operate. Finally make sure no obstacles may block the infrared communication between e.
12. Other Recommendations • Remove any small objects that may be on the road of the cleaning robot. • If the robot turns off automatically after bipping, it means that its battery is not charged enough any more. • Do not use e.ziclean® vacuum robot on thick or fringe carpets. • Avoid using the robot in particularly congested cables areas or anything else likely to get bogged down in the brush of your device. • Make sure the robot is fully charged before starting its cleaning work.
13. ERROR Codes instructions If the LED screen on the robot display an ERROR code, please refer to the following instructions to solve the problem. ERROR n° Meaning Solution Side brush engine issue Clean side brush and make sure it is rotating correctly. E002 Main brush engine issue Clean the overall main brush compartment. Make sure that both brushes are running correcly. E004 Left wheel engine issue Check the left wheel status. E005 Right wheel engine issue Check the right wheel status.
14. FAQ A. The Robot stops while operating Check if the selected cleaning time is over. Check if there’s any error information on the LED display and refer to the following explanations to solve it. B. The cleaner fail to work or the cleaning ability is weakened Check the battery status. Check whether the dustbin, the filter and the inlet of suction are cleaned; whether the side brush is working. Check whether the cleaner is turned on. C.
15. Certificates and Warranty e.ziclean® FURTIV warranty is 2 years. Accessories for 6 months. Please check on our www.ezicom.com website to know further about After Sales Conditions. For more information: . Warranty and After Sale Service Please contact us through our official website: http://www.e-zicom.com . How to use e.ziclean® vacuum robot cleaner Contact with your retailer or visit our website . Discover all accessories to equip e.ziclean® FURTIV robot All e.
