WATCHMINDER2 Thank you for purchasing the WatchMinder2. The watch was invented by a psychologist who works with children and adults who have attention deficit hyperactivity disorder (AD/HD). The watch has a number of other applications(see www.watchminder. com).
The WatchMinder2 has the following functions: TM & DT (real-time calendar clock) (P7-P8) B OR V (bell or vibration alarm) (P8-P9) TRAINING mode (use to train or improve a behavior) (P9-P17) REMINDER mode (use to remember a specific task or chore) (P18-P26) TMR (countdown timer) (P26-P28) SW (stopwatch) (P28-P29) SPECIAL OPERATING NOTES 1. The power consumption of the vibrator and EL backlight are quite high. A battery should last several months under normal circumstances.
for 10 seconds (one second bell/vibration with one second interval) unless it is turned off by a push of any button. 3. In setting time in all modes, a 24-hour system will be applied, but it will be displayed in a 12-hour system. (1 pm is "13") 4. Push LIGHT button, which is left blank without a label "LIGHT", the backlight comes on for 5 seconds and turns off automatically. 5. Push and hold down SW/+ or TMR/- button to count up/down rapidly after 3 seconds while setting. 6.
proof. DO NOT IMMERSE IN WATER. 10. Pressing RESET will delete all stored information in watch except personalized messages. 11. TRAINING and REMINDER modes can operate at the same time. 12. Messages repeat daily and there is no need to re-program the watch. HOW TO CHANGE BATTERY 1. One CR-2032 battery powers the watch (CPU, bell/vibrator and light). A capacitor is installed as back up power to allow an owner 4 to 6 seconds to replace battery.
open back cover unload battety load battery close back cover 2. Low battery warning: A symbol of low battery will appear at the 4th line at times when battery is low. An owner should replace the battery as soon as possible in this case. (Note: The symbol may only display while vibration/bell goes off or light is on.
SPECIAL NOTES FOR ALL MODES 1. A 60- second duration is allowed for an owner to make decision while setting. 2. A blank space and the following letters/ numbers/symbols (hereinafter referred to as characters) are in memory for an owner to create personalized messages. A message is limited to 9 letters/numbers/symbols and a blank space is counted as one character.
I. TM&DT 1. Push TRAIN/SET and TMR/- buttons together to go to TM&DT. (Note: Push TMR/- first and then TRAIN/SET) LCD displays Y00 M00 in the 2nd line and D00 W00 in the 3rd line; Year digit begins to blink. 2. Push SW/+ or TMR/- to adjust year. (Note: Number of year begins at 00 and ends at 99, i.e. when you go pass 99, it returns to 00.) 3. Push REMIND/GO TO button to go to month digit, which begins to blink. 4. Push SW/+ or TMR/- to adjust month. 5.
7. Push REMIND/GO TO button to go to hour digit (remember-24 hour clock), which begins to blink. 8. Push SW/+ or TMR/- button to adjust hour. 9. Push REMIND/GO TO button to go to minute digit, which begins to blink. 10. Push SW/+ or TMR/- button to adjust minute. 11. Push REMIND/GO TO button to go to second digit, which begins to blink. 12. Push SW/+ or TMR/- to adjust second. 13. Push TRAIN/SET button to enter. LCD displays current time. II. B OR V 1.
B OFF begins to blink. 2. Push REMIND/GO TO button to go to B OR V. 3. Push SW/+ or TMR/- to scroll OFF or ON. 4. Push TRAIN/SET to enter. If you turn B ON, you are in sub-mode BEEP. Symbol of beep displays in the 4th line. If you turn V ON, you are in sub-mode VIBRATION. Symbol of vibration displays in the 4th line. If you turn off beep and vibration, both symbols of beep and vibration disappear. When you turn on B OR V, you will hear a bell or feel a vibration. III.
BREATH (breathe); COUGH; FOLDIR (follow directions); FOLRUL (follow rules); GIVPOS (give positive reinforcement); GOODJB (good job); HANDUP (raise hand); IGNORE; POSIMG (positive image); POSTUR (posture); PRAY; PYATTN (pay attention); RELAX; REST; SIT; STOP; STRTCH (stretch). b. There are two alarm schedules FIXED (every 2,3,5,10,15,20,30,45 or 60 minutes) or RANDOM (CPU randomly chooses from 2,3,5,10,15,30 and 60 minutes).
d. If a TRAINING message is not responded to by pushing any button, except LIGHT and RESET buttons, it will come back with an alert in 30 seconds. This "snooze" feature is limited to one additional time. e. If the start time is set before current time, the TRAINING mode will not work for that day and will be activated the next day. f. If a TRAINING alert and a REMINDER alert are activated at the same time, TRAINING will win and REMINDER message will come on screen after TRAINING message disappears.
SET (set up training mode) REV (review or delete current training mode set up) in the 2nd and 3rd lines. Sub-mode NEW begins to blink. 2. Push TRAIN/SET button to enter. LCD displays in the 3rd line the first six characters of the table of characters in memory. The 3rd character begins to blink. 3. Push SW/+ or TMR/- button to select a character you would like to use. This selected character begins to blink. 4. Push REMIND/GO TO button to enter.
6. Push TRAIN/SET button to enter the personalized message into memory. LCD returns to step 1. 7. Repeat the above steps 2 to 6 to create two additional personalized messages. The 3 personalized messages will be saved in memory before the factory preset messages. 8. Push SW/+ or TMR/- button to go back to current time while sub-modes appear. DELETING PERSONALIZED MESSAGES 1. To delete a personalized message, push TRAIN/SET button to go to TRAIN.
the first personalized message in the 2nd line, which begins to blink/scroll, and the second personalized message in the 3rd line. (Note: If there is no personalized message in memory, the sub-mode DEL will not be activated.) 4. Push REMIND/GO TO button to go to the personalized message you would like to delete. 5. Push TRAIN/SET button to delete it while it is blinking/scrolling. LCD returns to step 1. 6. Repeat steps 2 to 5 to delete the other 2 personalized messages if necessary. 7.
blink. 2. Push REMIND/GO TO button to go to sub-mode SET. 3. Push TRAIN/SET button to enter. LCD displays the first preset message in the 2nd line, which begins to blink/scroll, and sub-modes FIX RDM in the 3rd line. 4. Push SW/+ or TMR/- to select a message you would like to have (see note a. on P9-P10 above). 5. Push REMIND/GO TO button to go to FIX, which begins to blink in the 3rd line. 6. Push REMIND/GO TO button to go to fixed intervals if you would like to use FIX sub-mode.
SW/+ or TMR/- button to select sub-mode RDM while FIX is blinking. Sub-mode RDM begins to blink. 8. Push REMIND/GO TO button to go to time setting. (In random sub-mode, CPU randomly chooses from these time intervals:(3,5,10,15, 20,30 and 60 minutes.) The start hour digit begins to blink in the 2nd line. You will see a letter "S" (meaning start time) right before the hour digit and a letter "E" (meaning end time) right before the hour digit in the 3rd line. 9.
while sub-modes appear. REVIEWING SETTINGS 1. To review/delete your settings, push TRAIN/SET button to go to TRAIN. LCD displays sub-mode: NEW DEL SET REV in the 2nd and 3rd lines. Sub-mode NEW begins to blink. 2. Push REMIND/GO TO button to go to REV. 3. Push TRAIN/SET button to enter. LCD displays your selected message in the 2nd line and submode REV DEL in the 3rd line with REV blinking. 4.
IV. REMINDER SPECIAL NOTES FOR REMINDER MODE a.
PLAY; PRAY; PRCTCE (practice); PU KID (pick up kids); READ; REST; SCHOOL; SNACK;STOP; STORE;STRTCH(stretch); STUDY; TEETH; TEST; TLKTCH(talk to teacher); TRASH; TURNHW(turn in homework); TV ; VIDEO; WAKEUP; WATER; WRITE. b. You are allowed to set up to 30 reminder messages and you can use the same message multiple times. If two messages are activated at the same time, they will come on screen in turn.
appointed time of the date in that particular year OR it will repeat annually without a year setting (00). If you set month, date and time for a reminder message, it will be activated on the appointed time of the date in that particular month OR it will repeat monthly without a month setting (00). If you would like to set a reminder message to repeat weekly, skip year, month and date (00) settings and set the day of week (01=Mon....07=Sun.) and time only.
will not work for the day and will be activated the next day. f. If a TRAINING alert and a REMINDER alert are activated at the same time, TRAINING will win and REMINDER message will come on screen after TRAINING message disappears. g. If you use a pocket organizer or PDA, use the WatchMinder2 to remind you to check your organizer (ORGNZR). You can have greater detail of the task to be performed in your organizer. CREATING PERSONALIZED MESSAGES (12 maximum) 1. Push REMIND/GO TO button to go to REMIND.
in the 2nd and 3rd lines. Sub- mode NEW begins to blink. 2. Follow steps 2 to 8 under TRAINING to set your 12 personalized reminder messages. DELETING PERSONALIZED MESSAGES 1. To delete a personalized message, push REMIND/GO TO button to go to REMIND. LCD displays sub-mode: NEW DEL SET REV in the 2nd and 3rd lines. Sub-mode NEW begins to blink. 2. Follow steps 2 to 7 under TRAINING to delete your 12 personalized reminder messages. SETTING UP REMINDER MODE Please read Note c.
1. Push REMIND/GO TO button to go to REMIND. LCD displays sub-mode: NEW DEL SET REV in the 2nd and 3rd lines. Sub-mode NEW begins to blink. 2. Push REMIND/GO TO button to go to sub-mode SET. 3. Push TRAIN/SET button to enter. LCD displays the first preset message in the 2nd line, which begins to blink. 4. Push SW/+ or TMR/- to select a message. 5. Push REMIND/GO TO button to go to time setting. LCD displays YEAR: 00 (2nd line) MO: 00 (3rd line). Year digit begins to blink. 6.
8. If you would like to set a reminder message for it to repeat weekly, push REMIND/GO TO button again to skip date (00) and the week digit (01=Mon....07=Sun.) begins to blink. 9. Push SW/+ or TMR/- button to adjust day of a week (01-07) and push REMIND/GO TO button to go to hour digit. Hour digit begins to blink. 10. Push SW/+ or TMR/- to adjust hour and push REMIND/GO TO button to go to minute digit. Minute digit begins to blink. 11. Push SW/+ or TMR/- button to adjust minute and push TRAIN/SET to enter.
REVIEWING SETTINGS 1. To Review/delete your settings push REMIND/GO TO button to go to REMIND. LCD displays sub-mode: NEW DEL SET REV in the 2nd and 3rd lines. Su-mode NEW begins to blinks. 2. Push REMIND/GO TO button to go to submode REV. 3. Push TRAIN/SET button to enter. LCD displays the first selected message in the 2nd line and sub-mode REV DEL in the 3rd line with the first selected message blinking/scrolling. 4. Push SW/+ or TMR/- to select the selected message you would like to review/delete.
item by item, or push REMIND/GO TO button to go to DEL if you would like to delete a setting and push TRAIN/SET to delete it. LCD returns to step 1. 6. Push SW/+ or TMR/- button to go back to current time while sub-modes appear. V. TMR (You can set TMR up to 99 hours 59 minutes and 59 seconds) 1. Push TMR/- button to go to TMR. LCD displays second digit in the 2nd and 3rd lines to the right, minute digit in the 3rd line to the left and hour digit in the 2nd line to the left. The hour digit begins to blinks.
3. Push SW/+ or TMR/- to count up or down to the number you would like to have. Push REMIND/GO TO button to advance to the next item you would like to adjust and push SW/+ or TMR/- to count up or down to the number you would like to have. Repeat until you set the countdown time you wish. 4. Push TRAIN/SET button to start countdown. 5. If you would like to engage an automatic repeat feature, skip step 3 and 4 and push REMIND/GO TO button until REPEAT notation "R" appears in the first line.
off automatically at the end of alert and LCD returns to current time. 9. Push SW/+ button to reset to zero during countdown and the TMR is ready to be set again or push TRAIN/SET button to interrupt and to go back to current time during countdown. Note: TRAIN or REMIND will win if it is activated while the TMR is running, and the TMR will be turned off automatically. VI. SW (You can time an event up to 99 hours, 59 minutes, 59 seconds and 99/100 second.) 1. Push SW/+ button to go to SW.
lines to the right, minute digit: 00 in the 3rd line to the left and hour digit: 00 in the 2nd line to the left. 2. Push SW/+ button to start the SW. 3. Push TMR/- button to pause and to stop the SW. Push TMR/- button again to continue. 4. Push SW/+ button to pause and to stop the SW and push SW/+ again to reset to zero. The SW is ready to be re-started again. Push TRAIN/SET button to interrupt and to go back to current time.
of purchase. This warranty does not apply to any watch which has been misused, neglected or damaged in an accident or in the replacement of batteries, or the back cover of the watch. The warranty is void if the watch has been tampered with by any person other than an authorized service center of WatchMinder2. The owner assumes full responsibility for damages incurred while changing batteries, the back cover and the wrist band.
Ship to: WATCHMINDER PMB #278 5405 Alton Parkway #5A Irvine, CA 92604-3718 USA IF YOU NEED TECHNICAL SUPPORT, CALL 800-961-0023. WATCHMINDER2 DOES NOT ASSUME RESPONSIBILITY FOR AN INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATIONS, DAMAGES OR INJURIES RESULTING FROM INACCURACY OR FAILURE OF THIS WATCH. THE WATCHMINDER2 IS NOT A SUBSTITUTE FOR PROFESSIONAL HELP. PLEASE USE THIS DEVICE IN CONSULTATION WITH YOUR DOCTOR OR CLINICIAN.
INC., PLEASE CONTACT THEM DIRECTLY FOR A REFUND. 30 DAY MONEY BACK GUARANTEE (APPLIES ONLY TO WATCHES PURCHASED DIRECTLY FROM WATCHMINDER, INC.). YOU MAY RETURN THE WATCHMINDER2 FOR A REFUND OF THE PURCHASE PRICE WITHIN 30 DAYS AFTER RECEIVING THE WATCH. TO OBTAIN THE REFUND, YOU MUST CALL 800-961-0023 (2#) AND GET A RETURN AUTHORIZATION UNMBER. RETURN THE WATCH WITH ALL PARTS AND PACKING MATERIALS, FREIGHT PREPAID, WITH A COPY OF THE ORIGINAL INVOICE. YOU MUST PAY THE SHIPPING BOTH WAYS.
