H980 Series 3G Router User Manual Industrial‐grade RF Module built‐in E-Lins Technology Co., Ltd ADDRESS: 1007A, MinTai Bld., Minkang Road, Minzhi Street, Bao'an District, ShenZhen, 518000, China PHONE: +86 (755) 33231620 WEB: http://www.szelins.
Manual Declaration Copyright All information in this user manual is protected by copyright law. Whereby, no organization or individual shall copy or reproduce the whole or part of this user manual by any means without written authorization from E-Lins Technology Co.,Limited.
H980 Series 3G Router User Manual CONTENTS CHAPTER 1 ABOUT THIS MANUAL ..............................................................4 1.1 Purpose....................................................................................................4 1.2 Applicable scope.....................................................................................4 1.3 Version information................................................................................4 1.4 Convention ....................................
H980 Series 3G Router User Manual Chapter 1 About This Manual This chapter briefly describes the function and role the this user manual has had, and gives the readers the information on how to read this user manual as the ® best guideline while E-Lins H980 Series series products are installed and operated. 1. 2. 3. 4. 5. 6. 1.1 Purpose Applicable scope version information Convention Technical support Acronyms and terms Purpose This user manual is developed mainly on the basis of H980 Series V1.
H980 Series 3G Router User Manual 1.4 Convention For reading and using this user manual fast and conveniently, the following conventions are reached for some abbreviations, icons, notes, security warnings and tips that appear in this user manual: Table -1.2: Convention Table Item 1.
H980 Series 3G Router User Manual 1.
H980 Series 3G Router User Manual HLR Home Location Register HSCSD High Speed Circuit Switch Data IGMP Internet Group Management Protocol IGRP Internet Gateway Routing Protocol IN Intelligent Network IP Internet Protocol IPv4 IP version 4 IPv6 IP version 6 IPSEC IP Secure Protocol ISDN Integrated Services Digital Network ISP Internet Service Provider L2TP Layer 2 Tunneling Protocol LA Location Area LLC Logical Link Control MAP Mobile Application Part MDNS Mobile Domain Name S
H980 Series 3G Router User Manual QoS Quality of Service RA Routing Area RADIUS Remote Authentication Dial In User Service RIP Routing Information Protocol RSC Register Service Center RTOS Real Time Operating System RTP Real-time Transport Protocol RTU Remote Terminal Unit RSVP Resource reSerVation Protocol SCADA Supervisory Control and Data Acquisition SGSN Serving GPRS Support Node SIM Subscriber Identify Module SMS Short Message Service SMSC Short Message Service Center SNMP
H980 Series 3G Router User Manual CHAPTER 2 Product Introduction 2.1 3G overview Combining with the third generation of mobile communication technology and WLAN technology, 3G mobile network data communication terminal product is designed as a high-tech 3G product upon the needs of users. It can provide data communication service for these users at any time and in any place. H980 Series 3G Router is characterized with excellent transmission reliability and a wide range of applicability.
H980 Series 3G Router User Manual The indicators on the front panel are described as the table below: Indicator LAN: NET: SYSTEM: State Description It lights shows there is a LAN connect, flash shows it has data communication. Indicate the status of module. It lights when router works normally. Back panel interface H980 Series 3G Router’s all interfaces are designed on the back panel as shown below: 3G ANT DEF LAN WAN CONSOLE USB POWER Wi-Fi ANT Fig. 2.1.
H980 Series 3G Router User Manual 2.1.2 Other Accessories For safe transportation purpose, H980 Series 3G Router should be packaged properly. Pease keep the packaging materials well after the package is opened for future use in case of re-transportation.
H980 Series 3G Router User Manual 2. This product is a Class-A information product, which may cause radio interference in living environment when being used. In this case, the users are required to take some proper measures. 2.1.3.2 Wiring RJ-45 - Ethernet interface Standard 10/100BaseT Ethernet switch port, self-adaptive DC - power supply interface, H980 Series 3G router’s power supply is generally +12VDC ANT - antenna interface The standard 5OΩ/SMA RF connector (female) is applied.
H980 Series 3G Router User Manual Supporting DMZ host computer Supporting DDNS Supporting static routing list Supporting IP address and port filtration Supporting monitor mobile network traffic quality. WEB/Telnet Management Local Firmware Upgrading/ Configuration Backup System Log Server 2.
H980 Series 3G Router User Manual z Application Mode Two: Application in SoHo There is one built-in 10M/100M self-adapting fast Ethernet port within H980 Series 3G Router, which greatly facilitates SoHo user getting access to the internet. Diagram 2.3-2: Schematic diagram for application in SOHO z Application Mode Three: Application in banking business H980 Series 3G Router is able to be connected to the target machine and other network devices at the same time.
H980 Series 3G Router User Manual Diagram 2.3-3: Schematic diagram for application in banking business Chapter 3 Router Configuration 3.1 Overview H980 Series 3G Router features built-in WEB interface configuration, management and debugging tools. Before using H980 Series 3G Router, users should configure relate parameters; during using, you can freely change related parameters and perform software upgrade and simple test etc.
H980 Series 3G Router User Manual 3.2 Connection settings 3.2.1 Environment requirements When you want to use H980 Series 3G Router, a computer and a UIM/SIM card should be prepared according to the following requirements: Computer with Ethernet card and TCP/IP protocol 1. 2. IE8.0 or higher Support 1024x768 resolution display 3.2.2 Connection method For your convenient use, we recommend you plug your SIM/UIM card into H980 Series’s card slot before your configuration.
H980 Series 3G Router User Manual Fig. 3.2.2.1: Wiring Method 1 Note: H980 Series 3G Router’s LAN port is designed with self-adaptive cross connect technology, so the straight-through cable or cross cable can be both applied to connect devices for communication. 3.2.2.2 LAN connection method When it is required to connect H980 Series 3G Router to local network through HUB or switch, connect the hub or switch out-link port with any one of its switch ports as shown in the figure below. Fig. 3.2.2.
H980 Series 3G Router User Manual adopted for some operating conditions, so you may place a lightning protection device between the connector and the antenna. Attention: 1. 2. 3. 4. The products shall be far away from any heating device; Don’t place the products in the dusty or wet environment; The products shall be far away from some potential interference sources, like the metal wall, and micro-wave oven, etc; Pay attention to the position and angle of antenna to ensure it works well.
H980 Series 3G Router User Manual Fig. 3.2.
H980 Series 3G Router User Manual Fig. 3.2.3-3: TCP/IP Properties Configuration Method 1: general configuration This method will temporarily interrupts the communication between the computer under configuration and LAN, and the specific parameter configuration is shown as below: IP address: 192.168.8.* (*indicates any integral between 2 to 254) Subnet mask: 255.255.255.0 Default gateway: 192.168.8.1 Remember: H980 Series 3G Router LAN port factory default parameter: IP address: 192.168.8.
H980 Series 3G Router User Manual The configuration operation is shown as below: Click the “Advanced (V)…”button in Fig. 3.2-5 to enter the interface as below: Fig. 3.2.3-4: Advanced TCP/IP Properties Configuration Click the “Add (A)”button under the “IP address (R)”, and fill in the IP address that you want to add: Fig. 3.2.3-5: Add TCP/IP Address After the configuration is completed, click the “Add”. By now the computer has a route to H980 Series.
H980 Series 3G Router User Manual Note: As shown in Fig. 3.2-3, “Default gateway” depends on whether the configuration computer connects with Internet through original local network configuration. If Internet is accessed through original local network, the default gateway setting does not need to be modified; if H980 Series 3G Router + is used, you need to modify the default gateway and configure it as H980 Series 3G Router’s default LAN IP address 192.168.8.1. 2.
H980 Series 3G Router User Manual And then you can enter user login identity authentication interface as shown below: Fig. 3.2.4-2: User Login Verification User should use default user name and password when log in for the first time: User name: admin Password: admin Input correct user name and password, and enter the WEB configuration interface. 3.3 WEB-based configuration H980 Series 3G Routers can be configured in WEB mode.
H980 Series 3G Router User Manual Drawing 3.3.1-1: System Configuration Window You can select the function and display the configuration window for the function after clicking on the related option on the top left corner of configuration window. Please see the following drawing: Menu Descriptions Drawing 3.3.
H980 Series 3G Router User Manual When you click the “Internet” tab, the following sub-tabs appear on the page: Mobile Network(Embedded Modem) Internet Connection Type Fig. 3.3.2: Internet Configuration Tab 3.3.2.1 Mobile Network configuration In the “Internet” main tab, click the “Mobile Network (Embedded Modem)” sub-tab to set the modem parameters and go to the following configuration interface: Fig. 3.3.2.
H980 Series 3G Router User Manual Note: “Embedded Modem” & “Module Modem” both mean the Modem embedded in H980 Series.
H980 Series 3G Router User Manual Fig. 3.3.2.1-2: PPP Advanced Settings 【The Net Type of Module】DEFAULT means router will obey default option to choose network; AUTO means router will choose available network automatically; other options mean router will use certain network only. Considering the difference of mobile network authorization, the Point to Point Protocol connection should be compatible with different network. Advanced setting is used for the PPP special setting.
H980 Series 3G Router User Manual 【LCP Echo Interval】: Set LCP’s maximum interval time, in second. 【LCP Echo Failure】: Set LCP’s maximum request times. 【MTU】: Set the number of bytes of the maximum transfer unit. 【MRU】: Set the number of bytes of the maximum receive unit. 【local IP】: Set the local IP address. 【Remote IP】: Set the remote terminal’s IP address. 【Other Options】: Users can define their own options here. 3.3.2.
H980 Series 3G Router User Manual 【Secondary DNS】: set the first backup DNS server’s address, which can be empty. 2. DHCP configuration When select “Automatic Configuration—DHCP”, enter the following configuration interface: Fig. 3.3-5: DHCP configuration interface Basically this do not need configuration, router will get IP address by DHCP service. 3. PPPoE configuration Select “PPPoE” and enter the following configuration interface: Fig. 3.
H980 Series 3G Router User Manual 【Password】: set the password of PPPoE service provided by ISP. 【Service Name】: set the service name of PPPoE service provided by ISP. 【Advanced Setting】: configure advanced parameters of dialing protocol. 3.3.2.3 Internet Connection Type configuration In the “Internet” main tab, click the “Internet Connection Type” sub-tab to set the internet connection type. Some pages also have button to link to this page.
H980 Series 3G Router User Manual Fig. 3.3.2.2: Modem configuration Interface 【DNS Customize】: Set whether configure the DNS server address manually: Enable/Disable. 【DNS1】: Set IP address of the primary DNS server. 【DNS2】: Set IP address of the standby DNS server. 【VPN Route Type】: Set whether all the packets will pass through VPN even the access to the Internet. 3. Custom configuration This mode is used for debugging; customers do not need it normally. 3.3.2.
H980 Series 3G Router User Manual 3.3.3 Local network When you click the “Local Network” tab, the following sub-tabs appear on the page: LAN WIFI Basic WIFI Security DHCP Server Static DHCP Fig. 3.3.3: Local Network Configuration Interface 3.3.3.1 LAN configuration In the “Local Network” main tab, click the “LAN” sub-tab to set the LAN port and enter the following configuration interface: Fig. 3.3.3.
H980 Series 3G Router User Manual Fig. 3.3.3.2: Wireless configuration interface 【Wireless Status】: set whether wireless network function is enabled. 【Wireless Mode】: Right now could only work as a AP. 【Wireless Network Mode】: set which protocols will be use, Could select only use 802.11b or 802.11g. 【Wireless Network Name】: set the name of your WIFI network. It must be unique in wireless network. 【wireless channel】: select the wireless channel.
H980 Series 3G Router User Manual 【WEP Shared Key】: set the keyword of WIFI. 3.3.3.4 DHCP server configuration In the “Local Network” main tab, click the “DHCP Server” sub-tab to set the DHCP server parameters and go to the following configuration interface: Fig. 3.3.3.4: DHCP Configuration Interface The configuration parameters include: 【DHCP Server】: Set whether enable the DHCP server function: Enable/Disable. 【IP Address Range】: Set the range of the DHCP dynamic address pool.
H980 Series 3G Router User Manual Fig. 3.3.3.3-1: DHCP Configuration Interface The configuration parameters include: 【Add】: Map the DHCP client’s MAC address with IP. 【Del】: Delete or release the mapping of MAC and IP. 【Refresh】: Refresh the information on the page. If you want to perform IP-MAC mapping, click the “Add” button to go to the following configuration interface: Fig. 3.3.3.3-2: Static mapping Configuration Interface 【MAC Address】: Set the MAC address. 【IP Address】: Set the IP address. 3.3.
H980 Series 3G Router User Manual Fig. 3.3.4: Applications Configuration Tab 3.3.4.1 DDNS configuration The router is designed with DDNS (Dynamic Domain System) function which can make others to search the dynamic IP address by internet domain. In the “Application” main tab, click the “DDNS” sub-tab to set DDNS parameters and go to the following configuration interface: Fig. 3.3.4.
H980 Series 3G Router User Manual Fig. 3.3.4.2-1: Time Operation Interface The configuration parameters include: 【Add】: Add the Timing Operation operated at certain time. 【Refresh】: Refresh the information on the page. 【Edit】: Edit selected Timing Operation. 【Del】: Delete Timing Operation. If you want to add the Timing Operation, click the “Add” button to go to the following configuration interface: Fig. 3.3.4.
H980 Series 3G Router User Manual 【Set Time】: We have five types of time: minute, hour, day, month and week. All you need processing the time is to fill each type with valid value. When setting, for each type of time, you need to split the different value with ",", and you can use "xx-xx" to represent a period of time. For instance, you can input the minute like this: 1, 2, 5, 10-59. Other types are as the same. 3.3.4.
H980 Series 3G Router User Manual Fig. 3.3.4.5: Interface Check 【Interface Inspecting】: Set whether enable the Interface Inspecting. 【Interface Name】: Set which interface will be check. 【Flow Direction】: the way to check data flow. 【Inspect Interval Time】: Set the interval of check. Caution: This function is used for avoid false connection. If enable it, when there is no data flow after a certain time, router will reboot itself. This certain time is 5 times of Inspect Interval Time.
H980 Series 3G Router User Manual Fig. 3.3.5-1: Security Setting Interface The configuration parameters include: 【Firewall Service】: Set whether enable firewall function: Enable/Disable. 【Default Action】: Set the default action of the firewall: “Accept” means the router accepts other packets by default; “Drop” means the router drops other packets by default. 【PING Accept】: Set whether allow PING router from outside. 【Remote HTTP Access】: Set whether enable the remote WEB management function.
H980 Series 3G Router User Manual You can choose filter type here: IP filter rules or MAC filter rules. Select the “IP Filter” to go to the following configuration interface: Fig. 3.3.5-3: Firewall Setting Interface The configuration parameters include: 【ID】: Set the identification of the firewall rule, generally using a name with meanings. 【Protocol】: Select the protocol of the firewall rule.
H980 Series 3G Router User Manual Fig. 3.3.5-4: Firewall Setting Interface 【MAC Address】: Set the MAC address. 【Action】: Select the actions to this rule of the firewall: Accept, Drop, Reject. 【Status】: Set whether enable this filter rule: Enable/Disable. 3.3.6 VPN If you click the VPN tab, the following sub-tabs appear on the page: L2TP PPTP GRE IPsec Fig. 3.3.6: VPN Setting Interface 3.3.6.1 L2TP configuration Fig. 3.3.6.1-1: L2TP Setting Interface 【Edit】: Edit the L2TP setting.
H980 Series 3G Router User Manual Fig. 3.3.6.1-2: L2TP Setting Interface L2TP configuration parameters include: 【Name】: Set a name for this L2TP connect. 【Status】: Set whether enable this L2TP: Enable/Disable. 【Server IP or Domain】: Input Server IP or Domain of the VPN service provider. 【User Name】: Set the user name provided by the VPN SP. 【Password】: Set the password provided by the VPN SP. 【PPP Configures】: Please see Chapter 3.3.2.1 as a reference. 3.3.6.2 PPTP configuration Fig. 3.3.6.
H980 Series 3G Router User Manual 【View】: View the status of PPTP, including Received Packets (TX), Received Errors Packets, Received Drops Packets, Received Bytes (RX), Send Packets (STX), Send Errors Packets, Send Drops Packet, and Send Bytes (SRX). 【VPN Route Type】: Link to the sub-page: Internet Connection Type. Click the “Add” tab; the following sub-tabs appear on the page: Fig. 3.3.6.2-2: PPTP Setting Interface PPTP configuration parameters include: 【Name】: Set a name for this PPTP connect.
H980 Series 3G Router User Manual 3.3.6.3 GRE configuration Fig. 3.3.6.3-1: GRE Setting Interface 【Edit】: Edit the PPTP setting. 【Del】: Delete the PPTP setting. 【View】: View the status of PPTP, including Received Packets (TX), Received Errors Packets, Received Drops Packets, Received Bytes (RX), Send Packets (STX), Send Errors Packets, Send Drops Packet, and Send Bytes (SRX). 【VPN Route Type】: Link to the sub-page: Internet Connection Type.
H980 Series 3G Router User Manual 3.3.6.4 IPsec configuration Fig. 3.3.6.4-1: IPsec Setting Interface 【Edit】: Edit the PPTP setting. 【Del】: Delete the PPTP setting. 【View】: View the status of PPTP, including Received Packets (TX), Received Errors Packets, Received Drops Packets, Received Bytes (RX), Send Packets (STX), Send Errors Packets, Send Drops Packet, and Send Bytes (SRX). Click “Add”, and enter link GRE tunneling configuration interface. Fig. 3.3.6.
H980 Series 3G Router User Manual circumstance to constitution Interface, Local Subnet, Peer Subnet, the Encrypt Type, Authorization, the related parameter of Password etc., be you usage static state ip address, Local ID and Peer ID don't fill. 3.3.7 Forward When you click the “Forward” tab, the following sub-tabs appear on the page: NAT & DMZ Static Route Fig. 3.3.7: Forward Tab 3.3.7.
H980 Series 3G Router User Manual Fig. 3.3.7.1-2: NAT&DMZ Setting Interface 【Select】: Select which data forward rule to be added. 1. Route mode setting Select the “Route Mode” option to go to the following configuration interface: Fig. 3.3.7.1-3: NAT&DMZ Setting Interface Route Mode configuration parameters include: 【Interface】:On selected interface, the source IP of packets pass through H980 Series would not be replaced to H980 Series’s IP, the destination machine can see the source IP directly.
H980 Series 3G Router User Manual Fig. 3.3.7.1-4: DMZ Setting Interface DMZ configuration parameters include: 【Outside Interface】: Set the interface on which the DMZ function acts. 【Inside Address】: Set the IP address of the host assigned by DMZ record. 3. NAT setting To configure the NAT function, you need to go to the following configuration interface: Fig. 3.3.7.1-5: NAT Setting Interface NAT configuration parameters include: 【Name】: Set the name mapped by NAT port.
H980 Series 3G Router User Manual 3.3.7.2 Static route configuration In the “Forward” main tab, click the “Static Route” sub-tab to set the static route parameters and go to the following configuration interface: Fig. 3.3.7.2-1: Static Route Configuration Interface The configuration parameters include: 【View Route Table】: View the current system’s route table. 【Add】: Add new static routes. 【Refresh】: Refresh the information on the page.
H980 Series 3G Router User Manual 【Gateway】: Configure the next IP address of this static route, namely the port address of the neighboring router. 【Interface】: Specify the interface on which the static route acts. 3.3.8 System tools When you click the “System Tools” tab, the following sub-tabs appear on the page: Local Log System Log Clock Account Backup Firmware Upgrade System Reboot Fig. 3.3.8: System Tools Tab 3.3.8.
H980 Series 3G Router User Manual 【Show】: Display log in the Log Table. 【Clear】: Clear the log in the Log Table. Log display: 【Log Table】: Display the system log information in the table. 3.3.8.2 System Log function In the “System Tools” main tab, click the “System Log” sub-tab to set the log function and go to the following configuration interface: Fig. 3.3.8.
H980 Series 3G Router User Manual Select the Manual to set the time manually. Select the NTP to go to the following configuration interface: Fig. 3.3.8.3: Clock Configuration Interface The system clock configuration parameters include: 【NTP Server IP】: Set the domain or IP address of the NTP server. 【NTP Synch. Interval】: Set the interval of the router making NTP synchronization in successive two times. 【Time Zone】: Set the time zone. 3.3.8.
H980 Series 3G Router User Manual 3.3.8.5 Backup In the “System Tools” main tab, click the “Backup” sub-tab to set the backup function. The configuration interface consists of two parts: the first part is parameters backup, namely send the parameters configuration information from the router to PC; the second part is parameters restoration, namely send the parameters configuration information from PC to the router. 1. Backup configuration See the figure below: Fig. 3.3.8.
H980 Series 3G Router User Manual 【Restore】: Import the parameters. 【Cancel】: Cancel the information in the address input box. 3.3.8.6 Firmware upgrade In the “System Tools” main tab, click the “Firmware Upgrade” sub-tab to use the software upgrade function and go to the following interface: Fig. 3.3.8.6: Upgrade Management Interface The upgrade configuration parameters include: 【Select】: Select the location of the upgrade software. 【upgrade】: Start firmware upgrade.
H980 Series 3G Router User Manual 【Reboot】: Reboot the system. After reboot the router, please reboot the browser. 3.3.9 Status display When you click the “Status” tab, the following sub-tabs appear on the page: Base Information LAN WAN Embedded Modem Route Table DHCP Client Fig. 3.3.9: Status Information Tab Tab description: 【Base Information】: Display the system information. 【LAN】: Display LAN port’s running information. 【WAN】: Display WAN port’s running information.
H980 Series 3G Router User Manual Chapter 4 Frequently Asked Questions (FAQ) 4.1 Fault analysis Fault 1: All indicators are off. Check whether the cables are connected correctly. Meanwhile, check whether the power supply complies with the requirements. H980 Series 3G Router’s label indicates the detailed requirements regarding the power supply voltage. Check whether the power supply voltage is identical with that specified in the label.
H980 Series 3G Router User Manual C:\>ipconfig Windows IP Configuration Ethernet adapter local connection: Connection-specific DNS Suffix. . . . : IP Address . . . . . . . . . . . . . . . . . . . : 192.168.8.48 Subnet Mask . . . . . . . . . . . . . . . . . : 255.255.255.0 IP Address . . . . . . . . . . . . . . . . . . : 192.168.0.48 Subnet Mask . . . . . . . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . . . . . . : 192.168.0.
H980 Series 3G Router User Manual Appendix: Software Upgrade Description Upgrade tool description and operating instructions H980 Series 3G Router is designed with the platform technology, whose software can be upgraded with the development of the communication and network technology. WEB upgrade: H980 Series 3G Router supports the function of upgrading the firmware directly by importing the upgrade file via the WEB configuration interface.
