User manual

ManualsBrandsE-Lins ManualsComputer equipmentH980 Series

TS2000: Tripod Turnstile

TS2011: Tripod Turnstile with Controller and RFID Reader

TS2022: Tripod Turnstile with Controller and Fingerprint Reader with RFID function

Please read this document carefully before installation and using the device.

1. Technical Specifications

Input Voltage

AC 220V / 110V,

50Hz / 60Hz

Max. Tolerance of Arms

Center: 80 kg

End: 40 kg

Rated Power

60 W

Ingress Protection Degree

IP54

Operating Environment

Indoor and Outdoor

Arm Length (mm)

500

Operating Temperature

-28ºC ~ 60ºC

Net Weight

46kg

Operating Humidity

5% ~ 85%

Gross Weight

54kg

Flow Rate

25~48 passages / minute

Dimension(mm) Figure 1

L = 1110, W = 260, H = 980

Input Control Signal

Dry contact

Package Size (mm)

L = 1200, W = 380, H = 1080

1110

500

260

980

1110

260

500

740

Figure 1

2. Arm Installation and Equipment Testing

2.1 Arm Installation Method

Installation procedure

1. Open the glue and apply in the square openings of

the arms as well as the four countersunk screws, as

shown in figure 2-1. (This is to prevent screws from

getting loose due to vibration after being used for a

long time.)

Figure 2-1

This opening shall be

applied with glue evenly.

TS2000 Series Vertical Tripod Turnstile User Manual

Version: 1.0 Time: 2014-3

Summary of content (10 pages)

PAGE 1
TS2000 Series Vertical Tripod Turnstile User Manual Version: 1.0 TS2000: TS2011: TS2022: Time: 2014-3 Tripod Turnstile Tripod Turnstile with Controller and RFID Reader Tripod Turnstile with Controller and Fingerprint Reader with RFID function Please read this document carefully before installation and using the device. 1. Technical Specifications Input Voltage AC 220V / 110V, 50Hz / 60Hz Max.
PAGE 2
. Insert the arms to the connection points, and use the Hex key to fasten the four countersunk screws on each arm, as shown in figure 2-2. Tighten the four screws on each arm in clockwise direction. Figure 2-2 2.2 Power-on Test Before the Installation of Device 1. Please make sure that the power requirements are strictly met to avoid permanent damage to the unit. You could change the input voltage 110V or 220V through the DIP switch, as shown in figure 2-3.
PAGE 3
Note: 1. When installing the tripod turnstile against the wall, please reserve at least 100 mm space in order to open the cover for adjustment and maintenance. 2. The space at the end of the arm shall not be greater than 80 mm (see figure 3-1). 3. Setting a warning line for card swiping (see figure 3-2). A warning line is suggested to prompt users to swipe cards in a distance, which would greatly reduce the probability of equipment failure caused by improper operations.
PAGE 4
. Cable Diagram 4.1 Function Description of the Turnstile Control Board If you are using TS2011 or TS2022, all the connections between access control and turnstile control board are done in factory. Just plug in communication cable to access controller and do the setting. If you are using TS2000, you need to connect access control system to the turnstile control board, please check the content in this chapter carefully.
PAGE 5
4.3 Parameter Configuration Function description of the DIP switch Down position indicates value 1. Up position indicates value 0. Figure 4-3 Pin 1 Function Setting 2 3 4 Opening Duration 5 6 Direction Indicator Memory Function 4.3.1 Setting the Turnstile Opening Duration Opening duration refers to the period of time from opening to closing once the turnstile receives an open signal. In the DIP switch, number 1, 2, and 3 are used for duration setting.
PAGE 6
4. It is recommended that a warning sign is placed at a conspicuous position, and prompt: "Please swipe your card outside the warning line and pass in order. Thank you!” The maximum tolerance of the tripod turnstile's arms Please note that the maximum stress tolerance at the center of the arm is 80kg and at the ends of the arm is 40kg (See figure 5-1).
PAGE 7
6. Troubleshooting Symptom The indicator is not lighted when the equipment is powered on. The arms of the tripod turnstile cannot be lifted manually after the equipment is powered on. The tripod turnstile does not open after authentication. The passing is not smooth after the turnstile is opened, it encounters resistance when pushing the arms, and the arms cannot return to the home position after they rotate. The arms drop during the use. Troubleshooting It may be caused by the power supply or circuit.
PAGE 8
Normal status of the drop-arm electromagnet after being powered off Normal status (closed) of the drop-arm electromagnet after being powered on Figure 6-3 Attachment 1- Default Factory Settings No. Function Default 1 Lock Driving Duration 5s 2 Door Sensor None 3 Verification Interval 1s 4 Controller Communication TCP/IP: 192.168.1.
PAGE 9
Attachment 2- Connection Diagram Overview 9
PAGE 10