NETWORK VIDEO RECORDER Plug In Auto Detect Rercord 01.BSM.15.0009501 Product Made in China under ISO9001 & ISO1400 standards Manual Printed in China v1.0 NVR Software Guide for setup and configuration.
Contents About this document About this document .................................................................................................. 2 Purpose This document is for Network Video Recorders, including the product features, hardware installation, network access, network configuration, daily maintenance, and troubleshooting. Contents ........................................................................................................................ 3 1 Preface ............................
9.5 Alarm Search ................................................................................................................ 55 9.6 NVR setup .................................................................................................................... 55 9.7 Network Camera setup ................................................................................................. 56 1 Preface 10 NVMS Access NVR ........................................................................................
1.3 Check the installation environment 2 Specification Installation environment Before installing the device, checking the environment according to the Table 1-1 Installation environment check items Check item standard Moisture-resistant The relative environment humidity must be in the range from 5% to 95%. If the humidity is higher than 95%, a dehumidifier must be installed, such as an air conditioner with the dehumidification function or a dedicated. Dehumidifier.
Recording time D1: stream 2 Mbit / s 2M x 3600s / 8 = 900MB / H (1 hour using 900MB of disk space) 720P: stream 4Mbit / s, 4M x 3600s / 8 = 1.8GB / H 1080P: Maximum stream 6Mbit / s, 6M x 3600s / 8 = 2.7GB / H 2 2T Hard Drive: 4 x 1080P can be kept for 15 days; 6 x 720P can be kept for 15 days; 12-channel D1 can be kept for 15 days 3 Operation instruction 3.1 Front panel description Figure 3-1 shows the front panel of the Network Video recorders. Table 3-1 shows the description of front panel.
3.2 Rear panel description 3.3 First boot Figure 3-2 shows the rear panel of the Network Video recorders. Table 3-2 shows the interface of rear panel. Figure 3-2 Rear panel Make sure that the right of access to power NVR. Ensure correct display HDMI or VGA interface connection. If the front panel of the power indicator lamp does not flash please plug in the power cable .Enable the power switch, NVR start running.
3.4 Shutdown If the equipment is not load, long press the PWR button on the front panel for more than three seconds, the device will shut down, solid red becomes red flashing power indicator panel after a successfully shut down. Shutdown process, the system prompts are off, do not cut off the power。 Equipment running directly through the rear panel power off switch, cut off the power or unplug the power cord should be avoided.
Figure 3-6 Camera dedicated network Back to Login interface ----END 3.6 Add Network cameras This NVR allow to connect maximum12 pcs network cameras. Recording baud rate totally is 24Mbps and live video total baud rate is 12bps. NVR maximum support to connect 12 pcs D1 resolution with average bard rate is 2Mbps network camera, If total baud rate more than 24Mbps it may cause NVR to lose video and not run stable.
Figure 3-1 Login screen Figure 3-2 NVR login interface Enter a user name and password into the login screen to enter the main page. Step 2 Click Login. Super user: admin, super user password: admin. User names and passwords are case-sensitive. Please modify the password after the first login. After three tries the user will be locked, and will no longer be able to continue to log in until the administrator can unlock the user, how to unlock Check Network Video Recorder User's Manual " management.
4 Quick configuration When the manual mode is selected, click Button for time synchronization. Select automatic synchronization mode, time synchronization automatically by NVR, this means all cameras will have internal times set to match NVR time. Area 2：NVR network configuration。 NVR default factory IP address: network 1:192.168.0.120, network 2: 192.168.1.120. The basic network configuration can configure the IP address, subnet mask, default gateway, DNS address and other parameters.
Figure 4-4 Device Discovery Tips Area 3：Hard disk management。 Format the hard disk will cause video loss, please use this feature with caution。 Power unit off to remove the hard drive, use the software to control this process as below otherwise it may cause damage to the hard disk recordings. Hard disk management for hard disk management NVR： Format hard disk. Click the Format button, pop-up prompts, choose to format. Capacity.
Figure 4-6 stream quick configurations Click the button ，Pop-up camera selection screen shown in Figure 4-4, the interface device selection, choose the camera finished, click Apply determine the choice. , Need to remove the management camera in the camera list, click the check box Select the camera, the camera button and then click Delete to remove. Area 6：Manage cameras certification account.
Decoding ability 5 Live video This system decoding ability is 6 channels D1 or 1 channel 720p or 1 channel 1080p. If it is over loaded, then it will print out”Decoding ability not enough” on the screen showing area. Intelligent adaptive mechanism of stream frame rates This system provides the intelligent adaptive mechanism of stream frame rates.
Items Name Figure 5-2 PTZ Control menu Content display the layout list, alarm list and alarm information. ：Play live video button. ：Close live video button. ：Mark tag button, you can mark the tag during the live video, it will helps to track the video fragment in recording playback. ：Click this button will call , we can select which one want to display according to the requirement. PTZ Control menu only can be cooperate with IPS Dome and Ext PTZ platform.
You can select the date period at the calendar. Click icon 6 Playback 、 to switch month, 、 to switch year. Means selected date. When it is green marked click means this day have recording files, otherwise there is none recording in that day. Step 3 Recording show. After selected the device and date, at the bottom area of the live video area it will display the recording status. The scale on the time axis showing the recording time period, blue marked means the current playback video time.
Figure 6-3 Backup path browser 4. Double click go into the network disc path list, select the backup path, click ok button save and exit. Step 2 Step 3 USB Storage device 1. Insert U disk or removable HDD to the USB interface. 2. NVR will detect the USB storage device automatically, after detected successfully, it will showing USB storage device. 3. Right click menu to select unmounts or formatting options on the U disk. 4.
Figure 6-6 File search 7 Alarm searching In alarm searching interface we can search the alarm recording. Operation steps Step 2 button enter into the alarm management interface like Click Figure 7-1 showing. You can select the camera which you want to search the alarm information from left list. Step 3 Means this camera have alarm information. We can select the alarm type at the Type drop-down menu. Step 1 Figure 7-1 Alarm searching interface. Step 4 Date selections.
After we selected the device and date, we can try to play the alarm recording files below type area. Step 6 Alarm triggers recording play. Select the alarm trigger recording files, click Step 7 8 Setup button to start playing. Alarm recording backup Select the recorded files and click backup button to make backup files. Setup includes NVR setup and camera setup. NVR setup for NVR configure and camera setup for cameras configure. 8.
Hardware Version Channel Qty Disk Qty Figure 8-3 Add IP section. Only Device Name can be edit, other parameters can’t be edit. When device update the device info will auto update as well and will keep same step with the software version. 8.1.2 Device Management User and search, add, delete cameras through device management.
Step 3 Click Figure 8-6 System warning information. button to call the interface as Figure 8-5. Figure 8-5 Add camera management Warning information searching steps. Step 1 Select the warning type (Disk Alarm, Record Alarm, All). Step 2 Input searching Begin Time and End Time. Step 3 Click searching button , then the searching result will be displayed below. ---- End 8.1.4 Network You can check the Camera DHCP IP address, configure IP address, subnet mask, gateway address, First NDS, backup NDS.
Figure 8-7 Network interface Edit current layout Create New layout The steps to create new layout below: Step 1 NVR Setup> Live Video Layout Enter the live video layout like Figure 8-8. Figure 8-8 Live video layout Step 2 Configure the network parameters, reference the Table 8-1. Table 8-1 Network parameters Step 3 Items Introduction How to configure Get IP address automatic ally It will get the IP address from DHCP server automatically. Switch DHCP to on by this button .
Step 3 Step 4 Input the New layout name Configure the New layout position, you can select the Shared layout or my layout. Step 3 Step 4 Call the record policy configuration interface like Figure 8-11. Shared layout means the layout for all the users. May layout means the layout for current login user only. Shared layout only can be created by authorized users. Step 5 Step 6 Please select “√” on the cameras which you want to record, and also select the corresponding streams parameters.
Figure 8-12 Schedule record configuration 8.1.7 Storage policy In storage policy interface, you can do the following operates: Check the current HDD status. Check the HDD information details; include HDD capacity, free space. Unload and Format operates. Firstly using HDD need to format first otherwise the recording file cannot be written into the HDD. Select System configuration>Record>Storage Configuration. Enter the Storage Configuration, like Figure 8-13 showing.
Backup Alarm search System Management Shutdown Record service Set shared layout Accounts>Group 2. Click yes to return to the original interface. 3. Click Apply to finish the operation. Step 1 System default privilege group is Administrators, which cannot be deleted and modified. User setting You can add and delete users, the users which have the privilege of system configuration can unlock the system which may be locked by serial login with incorrect password.
5. Click Apply to finish the user adding configuration. Delete user. 1. Click delete to call the delete user interface. 2. Click yes to return the previous interface. 3. Click Apply to finish the user operates. 9 Unlock the locked user When login to the system, if the user input the wrong password more than 3 times, then the system will lock the user, but only the administrator can unlock the users.
Super user: admin, super user password: admin. User names and passwords are case-sensitive. Please modify the password after the first login.
Figure 9-6 set user video ability Figure 9-7 Live video If other users set to be maximum ability the interface will back to Figure 9-6 and can’t set the ability anymore. If setting failed a failed message will be display. 9.3 Live Video After login the Web, we can see the live video by select the cameras show in Figure 9-7. 9.4 Playback You can play back the video by Playback interface. Operation Steps Step 1 Click Playback to enter the playback interface show in Figure 9-8 .
: Play, Stop, Fast forward, Rewind Figure 9-8 Playback 9.5 Alarm Search Click the Alarm Search inter the alarm management interface show in Figure 9-9. Figure 9-9 Alarm search ---- End Step 1 Step 2 Step 3 Choose the device on the left that need to see the alarm information. Choose the alarm type by the bar Type. Choose the date. Means the Check the date on calendar. 、 change month, 、 change year. date chosen. If the date with Red color means this day exist Alarm video recorded, or will not.
(Detail setting please refer to 8.1 NVR setup) Figure 9-10 NVR setup interface 10 NVMS Access NVR Operation condition You have installed NVMS already. The NVMS client installation method please see "video network management system manual” 10.1 Start and Run If you have installed NVMS please run it by this icon to the Login interface. 10.2 Login When the Login interfaces, enter default user name: admin. Password: admin show in Figure 10-1. 9.
10.3 System main interface After enter the correct user name and password: click Login to system main interface show in Figure 10-2. Figure 10-2 main interface Only Device Name can be edit ,other parameters can’t be edit When device update the device info will auto update as well and will keep same step with the software version. Operation Steps Step 1 select Device manager->NVR management->Device Info The NVR information will show as Figure 10-3. Figure 10-3 Device info interface 10.
Figure 10-4 Login interface Step 2 Change the NVR date and time Click the Set button behind the Current Computer Time to sync the time from PC to device. Set the Computer current time to be NVR time. Set manually to change time. Click Set the date. Input the time after the date. button to call the date ActiveX. ---- End 10.4.4 Device Management Add / Delete the IP cameras to NVR through the Device management.
Figure 10-8 record policy Select the devices which you want to delete, click delete then can delete the cameras which you added Step 5 Click Apply to call the “configure successfully interface”, click OK to save the configuration. Figure 10-7 Add device Step 2 Select the device and click Configure. After promote the Record Policy Setting then can set the Schedule record, Alarm Record, audio record etc. ---- End Step 3 Set the policy which you need.
Figure 10-9 Record Storage Step 3 Select Enable. Step 4 Select the DiskGroupID. Step 5 Input the UsableSpace. Step 6 Click Modify to save the configuration and exit the interface. Step 7 Select the file system. Step 8 Click DiskFormat to format the disk. It will ask you all the information which has been saved in Disk will be cleared, if yes, then it will start to format. ---- End 10.4.6 NVR Monitor NVR Bear panel has a VGA output and a HDMI output interface.
10.5 Playback 10.5.2 Backup Enter the Backup interface, select the video that need to backup by mouse drag on the time axis and right click mouse->Backup to start the video backup. NVMS can remote playback the NVR recording video. 10.5.1 Video Search and playback Blue file on time axis is the video chosen for backup. Press Ctrl to select more part video. In the main interface, click Playback enter the interface, and click the NVR Icon” ” enter NVR Playback show in Figure 10-12.
