Network Video Manager System User Manual V1.7 Thank you for purchasing our products, please contact us at anytime if you have any question or requirement. It’s possible that there might be inaccurate places, inconsistencies between function and operation or print mistakes. We will update the manual according to the technical change, and shall not notify in advance with only renewing the manual contents.
Network Video Manager System -CONTENTChapter 1 Installation for software ................................................................................................................................................ 2 Chapter 2 Setup parameter through software ............................................................................................................................... 3 2.1 LOGGING IN AND INTERFACE .........................................................................................
Network Video Manager System Chapter 1 Installation for software Important Note: Please notice that the video card driver must support the hardware speedup function. NVIDIA GeForce 6200/6600/7400/8600/9500/9600 series etc, ATI Radeon 7000/7200/7500/8500 /9000/9200 /9500/9600 series have already been tested. Double click Setup.exe, will pop up the installation confirmation dialogue box as below: Click “NEXT”, will pop up the dialogue box.
Network Video Manager System Click “Finish”, the client-side software will be installed in default directory. Chapter 2 Setup parameter through software 2.1 Logging in and interface After installation of software, click " " icon on the desktop will pop up the dialogue box, the username and password must be input for logging in. Important Note: The default system super user and password are both "admin". User name and password are case-sensitive.
Network Video Manager System Input the default user name and password, click ‘logging in’ button to enter the real time surveillance interface. IP Address: client software used by the local IP address. Note: Enter the user name and password three times wrong, The user name that is locked into the state, Before unlocking the former will not be allowed to re-use, If you need to unlock the super-user must log on the client in the "System Settings" "user" option in the "unlock" operation. 2.
Network Video Manager System Video Cycle Setting Record ON/OFF Audio ON/OFF Record Icon Video turnoff PTZ three-dimensional positioning ON/OFF Device List Video Information Menu of right mouse Voice Setting PTZ control Stop Play Single full Screen Hide information Snapshot Image quality Image partition Note: Hover the mouse button 1 second, will automatically display the name of the button. 2.2.
Network Video Manager System : Play button, select the host IP in the list, click Play Button to connect images of the selected the host. : Stop button, stop connection to the selected host. : Camera button, click this button to save the current image in single/series mode. Select camera setup will pop up the camera setup interface, see below: : Video quality button, after click, will pop up the image quality adjustment interface, see below. It’s available to adjust bit rate and quality value.
Network Video Manager System : Full screen button for Single video: when clicked, the selected video will be full screen. : Hide Information button: when clicked, the selected information column of video will be hidden. : Volume on-off and adjustment button. : PTZ 3D positioning: When you enable this function, you could use the left mouse button to click on video window and the PTZ will be automatic pointed to the video central.
Network Video Manager System 2.2.2 Device group settings Right-click on the "device list" and select "Add Camera Group", the new device group will be added, as follow: Right-click on the new device group, the new camera group can be added, deleted and renamed operations. As follow: You could click left mouse button to select the device and drag it on camera group. 2.2.
Network Video Manager System ：It is the start, pause, stop, previous screen and next screen button from left to right ：It is the add group, delete group and configuration button from left to right. Right-click on “Cycle list” and choose the “add cycle group” pop-up menu, a new cycle group will be added. As follow: Right-click on the new cycle group, the pop-up menu will be showed the add cycle group, delete cycle group and cycle configuration functions and so on.
Network Video Manager System Display: The screen display has the 1, 4, 8, 9, 16 and 36 channels. For example: when the screen display chooses the NO.4, the each cycle screen will be showing the 4 channels. Choose devices which have needed to cycle in device list, and click the to cycle group.
Network Video Manager System For example as above, there are 5 screens in cycle group and interval time is 10 second. When cycle is starting, each screen which had 4 channels has showing 10 seconds every time. Right-click on the new screen, the pop-up menu will be showed the add screen, delete screen and rename screen. As follow: Click the button to save the cycle configurations. Right-click on the new screen, you could click the “start cycle” in pop-up menu and click quarter to start the cycle.
Network Video Manager System 2.
Network Video Manager System 2.3.1 Conventional option 1. Client-side voice selection: English, Chinese, Russian, German, French, Japanese, Spanish and Portuguese. 2. Open to auto-startup: select YES to setup auto-startup. 3. Recording service auto-startup: select YES to setup auto-startup. 2.3.2 Default Device Users Add the username and password of devices, so the soft client could connect to camera and get the parameters automatically. 2.3.3 Video display and transmission include: 1.
Network Video Manager System 2.3.4 PTZ keyboard This function may through PTZ the keyboard connection computer remote control IP speed dome. Specific connection diagram is as follows: 2.3.5 Communication port settings Communication Port Settings to set alarm center listen port, register service listen port and broadcast service listen port. Alarm center to listen the default port 30004, Register services to listen the default port 30005, Broadcast service to listen the default port 30003. 2.3.
Network Video Manager System Active Search: First configure the IP range; the soft client will take the initiative to search for Network devices within the IP range. 2.3.7 Concentrate Record 2.3.7.1 Record Manager Click the "Record Manager" into the record management interface, as follow: Add the record device.
Network Video Manager System Choose record devices in the device list, add click the please click the button. If you want to configure the record parameters, button, the pop-up window will be showed as follow: Configure parameters of the record rule and stream. Disk group: The default is divided into 8 groups of disk group, the videos are recorded to a different disk group. 2.3.7.
Network Video Manager System The store path is including the local path and NAS path. Local path: Click the button, Pop-up Record Directory Add window, select the local hard disk type, as shown below: Click on the "Browse" button to eject the browse folder interface, select the video that you want to save the path after the click OK.
Network Video Manager System NAS path: Click the button, Pop-up Record Directory Add window, select the NAS disk type, as shown below: Set the correct IP address of the NAS, path, username and password, click the Click button. button to save the store configuration and return the record manager interface, then click button to start the concentrate record. 2.3.8 Permissions settings 2.3.8.1 Permission group settings Permissions group can add, delete and modify user rights group.
Network Video Manager System Need to add permissions group click the "Add" button, pop-up window as follows: Fill in the required group name and description, and click OK: Click new group permissions, and then in the distribution of the basic rights need to check before, click the "Save" button; complete the group permissions to add.
Network Video Manager System 2.3.8.2 User Settings Users can add, delete and modify the user's user name and password. And can unlock the user has been locked. Only super-administrator (default username is admin) can unlock locked users.
Network Video Manager System 2.3.9 System log Select "System Log", in the query needed to enter query conditions, click on "Search" button; you can query the system log: System log types include five options: all types, real-time video, voice intercom, log on to the system and setting of equipment parameters。 The query system log is the client local database log records. 2.
Network Video Manager System 2.4.1 Device manager Click device button to enter the interface as shown in figure: Input information such as IP address and name, etc, click “add” button, then “save” button, the added host will be shown in the host list of “real-time surveillance”, double click to connect the host. If you need the router port mapping, you could choose "Enable router mapping".
Network Video Manager System router's WAN address. The control mapping port and TCP A/V mapping port will be added the entrance port within the router can be set up. 2.4.2 Device setup Click the host in the from the Device Setup interface, to connect the host to configure its parameters。Include: device information, configure the device user name and password login, equipment hardware, alarm configuration, local recording, CMS configuration, network services and restart the equipment. 2.4.2.
Network Video Manager System microphone option, PTZ parameters, RS485 parameters and disk format. 1. The local network parameters Can set the network IP camera address, subnet mask, gateway, DNS and other network parameters, If it is used in local area network You are cautioned not to set up the internal LAN IP address and computer IP address conflict .If you want to modify equipment IP protocol, the client must restart the selection of the corresponding IP protocol registry.
Network Video Manager System Note: IPv6 addresses do not need to set the subnet mask. 2. Device Port Control port: The default is 30001, including the parameters of reading and writing, PTZ control and so on through this port to control; TCP audio and video port: The default is 30002, for the TCP protocol under the audio and video transmission which needs of the port number. Http Port: Default is 80, for Web access to use the port number.
Network Video Manager System 4. Date and Time Select the method to use for setting the time: one is to set the time according to the clock on your computer; another is to manually enter the time and date. 5. Camera settings Camera Name: Options need to set up its camera, you can set the camera in both Chinese and English names. Name of the success of the camera settings will be displayed in real-time monitoring--Device list. Signal system: PAL or NTSC.
Network Video Manager System 7. Microphone settings In microphone: Equipment for IP Camera with built-in microphone near the camera. Out microphone:IP Camera equipment to the Audio In interface panel by the external microphone access. 8. PTZ settings IP Camera equipment can be used in front-end to configure the device PTZ corresponding PTZ parameters. Including PTZ Protocol, PTZ Address, Serial Port, Baud Rate, Data Bits, Stop Bits and Parity Verification. 9.
Network Video Manager System 1. Alarm I/O Parameter Configuration Alarm input: Select the alarm input configuration ID, the alarm can be configured in both Chinese and English entered the name and the effective level. Effective level include: high and low two options. When you select high effective input port when access to high level alarm that is triggered by alarm signals, When you select low effective input port when the alarm signal that is triggered off high alert.
Network Video Manager System 2. Disk Alert Configuration Disk Alert configuration including: disk error alarm and disk full alarm. Disk alarm will be recorded in the alarm log. 3.I / O alarm linkage configuration Note: Before the opening of the record, we must first configure the "Local Record""Record Policy" parameter. Options need to configure the alarm I/O of the ID number, can be configured in the Alarm I/O trigger the alarm when the linkage.
Network Video Manager System Select "Enable PTZ", Click "PTZ alarm settings" can be set to trigger alarms when the PTZ preset position and name. 4. Motion Detection Alarm Configuration interaction Note: Before the opening of the record, we must first configure the "Local Record""Record Policy" parameter. Options need to configure the camera ID number, can be configured to detect movement of the camera to trigger the alarm when the linkage.
Network Video Manager System Require the deployment of the week, and set the beginning and ending days of deployment time, click the "Add" button, click "OK" button. Click on "Detection of regional Configuration": Area Motion: Press and hold the left mouse button on the video in order to facilitate the sliding region configured to detect regions, when the need to remove the detection region can click the right mouse button. The most mobile region can not detect more than eight.
Network Video Manager System Need to set up the camera to choose ID, you can set the camera to record the quality of SD cards, including: resolution, frame rate, bit-stream parameters. Schedule Record: Including 7X24-hour record and schedule record.
Network Video Manager System Days to keep video: Retain the largest number of days for 9999 days. Stream: Recording selected video stream ID. 2. Record Directory Set the device to the video directory, default including the SD card and NAS in two directories.
Network Video Manager System Set the correct IP address of the NAS, path, username and password, Click enabled, you can record video directly to a device on the NAS. 2.4.2.6 CMS Configure CMS configuration includes alarm center, register center, FTP, and SMTP parameter settings. 1.
Network Video Manager System Alarm Center: When a warning alarm triggered when uploaded to a designated alarm center. Alarm Centre will pop up with an icon of a warning light in the in the lower right corner of the screen , click , the alerts information pop-up window will be showing current alarm information, the alarm log can also be searched through Alarm Manager. 2. Register Center Registration center: IP Camera device to set the address registration center to register. 3.
Network Video Manager System 4. SMTP After SMTP is enabled, when triggered by motion detection, alarm and I / O alarm will be automatically sent JPG pictures and alarm information to the recipient's mailbox. 2.4.2.
Network Video Manager System 1. NTP NTP: Network Time Protocol。Host can automatically adjust the clock of the computer and connect sync. Click "Apply" button and then automatically adjust the time, In addition, 12 o'clock everyday, the automatic adjustment of service start。 2. PPPoE PPPoE: Network Camera support agreement based on the PPPoE WAN access.
Network Video Manager System Upgrade cycle: unit is minutes; the upgrade process for each time interval to upgrade the server asked whether there is a need to upgrade the new version. Specific steps to upgrade please refer to "Chapter III." 2.4.2.8 Device to restart IP CAMERA to use remote control equipment, to resume operation. 2.4.2.
Network Video Manager System ：It is the play, pause, stop, previous frame, next frame, 1/2 speed, 1/4 speed, 1/8 speed 1/16 speed and fast speed button from left to right. ：It is the zoom in, zoom out, default, 10 seconds zoom in, 30 seconds zoom in, 1 minute zoom in, 5 minutes zoom in and 10 minutes zoom in button. These buttons could control the scale of time line. Choose cameras which you want to playback in device list and input searching time between beginning and end time.
Network Video Manager System 2.6 Alarm Manager Click on the top of button, Access to the Alarm Manager interface, choose “Alarm Search”, in the query, the input conditions required to query, click “Query” button, Can query the police log. Alarm types include four options: all types, I/O alarm, motion detection alarm and disk alarm.
Network Video Manager System Chapter 3 Remote equipment maintenance and upgrade First of all, please download the upgrade package to upgrade. The directory where the package was putted in can not contain spaces, so it must not be on the table. After the download is complete, open the "UpdateTool" directory, double-click "UpdateTool.exe", and begin the upgrade operation. 3.1 Server Configuration 3.1.
Network Video Manager System b. Choose the path of the upgrade package from the “Browse”. Please note that the path of upgrade package has not included space. c. Click “Upload” and the upgrade package will be uploaded to the product root directory. 3.3 Update Device 3.3.1 Function Description Configuration upgrade version and scope. 3.3.2 Configuration Method a.
Network Video Manager System b. Please select the model and version from each list which you want to update devices to. The default value of model is IPC8180. c. You could add and select Network video Device barcodes which you want to update. If you want to update all of devices in the LAN, you only select the “all” item directly. Note: The barcode number usually be marked on the shell of device. d. Click the “Update” to upgrade device. e.
Network Video Manager System Note: All “update service” parameters of Network Video Devices must be as same as the “Server IP” in the update tool. You could setup it according to “3.4” chapter. 3.4 Configuration front-end products to upgrade the server parameters 3.4.
Network Video Manager System c. Select bar “Network Service”, and then click “Update”. d. Fill in the IP address and port of the Upgrade the server on the right (must be configured the same as in step 1).
Network Video Manager System e. Configuration upgrades time, in minutes. Upgrade procedure for each interval that is long time to upgrade the server asked whether there is need to upgrade the new version. f. Click "OK" the application of the revised configuration. After the entire configuration, wait a few minutes, the front-end device will automatically upgrade. 3.5 Notes a. Upgrade tool (UpdateTool.exe), updateserver (updateserver.exe) and serverParameter.ini, Must be located in the same directory. b.
Network Video Manager System maintenance", IP Camera manually add devices such as IP address information, the save operation, can be a normal visit to IP camera equipment. 7.
Network Video Manager System want to visit the IP Camera Host IP address, click the enter key (ENTER), the login dialog box enter the correct user name and password to access the IP Camera equipment .IP Camera equipment default user name and password are admin, case-sensitive. 8. IP Camera equipment how to WAN connectivity and access? IP Camera equipment can be PPPoE dial-up to connect to the WAN network, to support the DDNS to visit.
Network Video Manager System 12. Which external devices can work together with IP Camera? IP Camera can be used in conjunction with the keyboard; can access a wide range of control decoders, alarm input and output devices, alarm host, access control systems.
