Apprentice S 15e RTF with DXe Manual

EN
IMPORTANT: If using the buddy box option for training on a transmitter other
than the included DXe use these settings for a Master and or Slave Transmitter.
Failure to do so will not allow SAFE technology Flight modes to work correctly.
IMPORTANT: If using the buddy box option the transmitter must be confi gured
using the Transmitter Setup and Buddy Box setup charts.
* Refer to your transmitter’s manual for more information about Wireless Buddy
Box Setup.
Optional Transmitter Setup
Buddy Box Setup
Transmitter
Gear/
Ch 5
Aux 1 Flight Mode/ Panic Switch
SAFE Flight Modes
Supported
Panic Recovery
Switch
SAFE Flight Mode
Switch
Throttle, Aileron, Elevator and Rudder are in Normal position.
DX4e (2pos) N
N/A Default 2 pos Trainer ACT / AUX
DX4e (3pos) N
N/A Default 3 pos Trainer Ch 5
DX5e (2pos) N
N/A Default 2 pos Trainer Ch 5
DX5e (3pos) N
N/A Default 3 pos Trainer Ch 5
DXe N
N/A Default 3 pos Trainer Ch 5
DX6i
R N
*(Flap System) Norm  100 Land  100
2 pos Flaps GEAR / F MODE
DX7 NN
*(Flap System) Norm  100, Mid  100, Land  100
(3 pos Aux1 switch–0 & 1 are normal 2 is panic)
2 pos Flap GEAR
DX7s N
R *(Switch Select) Gear to INH, FM to INH, Flap to Gear, Trainer to Aux1 3 pos Trainer Flap
DX8 N
R *(Switch Select) Gear to INH, FM to Gear, Flap to INH, Trainer to Aux 1 3 pos Trainer F MODE
DX6
DX7(G2)
DX8(G2)
DX9
DX18
DX20
N
R *(Channel Input Confi g) Gear is B, Aux1 is switch i 3 pos Bind / i B
DX10t N
R *(Channel Input Confi g) Gear is A, Aux1 is R stick 3 pos R-Tip A
N = Normal R = Reverse
Master Transmitter Setup Slave Transmitter Setup
Master Transmitter Master Setup Slave Transmitter Slave Setup
DX4e, DX5e (2pos) Factory Trainer Settings DX4e, DX5e (2pos) Factory Trainer Settings
DX4e, DX5e (3pos) Factory Trainer Settings DX4e. DX5e (3pos) Factory Trainer Settings
DXe Factory Trainer Settings DXe Factory Trainer Settings
DX6i Factory Trainer Settings DX6i Factory Trainer Settings
DX7 Trainer to Normal DX7 Factory Trainer Settings
DX6*
DX7s
DX7(G2)*
DX8
DX8(G2)*
DX9*
DX10t
DX18
DX20*
Activate Programmable Master and insure
channels Thro - Aux 1 are set to slave
DX6
DX7s
DX7(G2)
DX8
DX8(G2)
DX9
DX10t
DX18
DX20
Factory Trainer Settings
If using any DSMX transmitter other than the included DXe (3 pos gear switch)
the radio will have to be confi gured correctly for the SAFE system to work
properly.
• SAFE Flight mode is selected using Channel 5 signal (high, middle, low)
• Panic mode is selected with Channel 6 signal (high, low)
Refer to your transmitter’s manual for more information about transmitter
setup.
Refer to the Receiver Setup section of this manual to select the SAFE Flight
modes you desire to use on a transmitter with only a 2 position Channel 5
switch.
23