Owner's manual

-3-
advance to the first selection again.
Programming Menu 3 – Timing
The default setting is 15 degrees. As a general rule, lower pole count
motors use lower timing and higher pole count motors use higher timing.
Please refer to your motor instructions and specifications for an indication
of the number of poles.
LOW TIMING ADVANCE
TimingDegrees–5&10
MotorPoles–2to4
ExpectedPerformance–Goodbalanceofpowerandefciency
MotorPoles–6ormore
ExpectedPerformance–Bestefciencyandruntime(lowestpower)
STANDARD TIMING ADVANCE
TimingDegrees–15&20
MotorPoles–6to12
ExpectedPerformance–Goodbalanceofpowerandefciency
MotorPoles–14ormore
ExpectedPerformance–Bestefciencyandruntime(lowestpower)
HIGH TIMING ADVANCE
TimingDegrees–25
MotorPoles–12
ExpectedPerformance–Highestpower,lessefciency
MotorPoles–14ormore
ExpectedPerformance–Goodbalanceofpowerandefciency
1.Movethesticktocenter(between1.4and1.6ms)for5seconds,and
the controller will beep 3 times, indicating you are now in Menu 3.
2.Movethethrottlesticktofullthrottle(>1.7ms)positiontomake
changes to the Timing programming.
 a.Toselect5Degrees–Youwillhear1shortbeep.Move
  thethrottlesticktocenter(between1.4and1.6ms).The
  controllerwillbeep2times,indicatingyouhavesetthe
program selection or leave in full throttle for 5 seconds to
advance to the next selection.
 b.Toselect10Degrees–Youwillhear2shortbeeps.
  Movethethrottlesticktocenter(between1.4and
  1.6ms).Thecontrollerwillbeep2times,indicatingyou
have set the program selection or leave in full throttle for
5 seconds to advance to the next selection.
 c.Toselect15Degrees–Youwillhear3shortbeeps.
  Movethethrottlesticktocenter(between1.4and
  1.6ms).Thecontrollerwillbeep2times,indicatingyou
have set the program selection or leave in full throttle for
5 seconds to advance to the next selection.
 d.Toselect20Degrees–Youwillhear4shortbeeps.
  Movethethrottlesticktocenter(between1.4and
  1.6ms).Thecontrollerwillbeep2times,indicatingyou
have set the program selection or leave in full throttle for
5 seconds to advance to the next selection.
 e.Toselect25Degrees–Youwillhear5shortbeeps.
  Movethethrottlesticktocenter(between1.4and
  1.6ms).Thecontrollerwillbeep2times,indicatingyou
have set the program selection or leave in full throttle for
5 seconds to advance to the first selection again.
Programming Menu 4 – Throttle Input Range (PWM)
Thedefaultsettingis1.2msto1.8msandshouldworkwithmostradio
systems. This option allows for proper throttle input with many different
radiosystems.However,someradioshaveawideroutputrange,andmay
giveamorelinearresponsewiththe1.1msto1.9msrange.Ifyoufeel
there is too much “dead” area in the stick movement near full throttle, try
adjusting the end points in your radio, or change to the wider input range.
Be aware that if these settings are not correct, it may be impossible to
arm the controller.
1.Movethesticktocenter(between1.4and1.6ms)for5seconds,and
 thecontrollerwillbeep4times,indicatingyouarenowinMenu4.
2.Movethethrottlesticktofullthrottle(>1.7ms)positiontomake
 changestotheThrottleInputRangeprogramming.
 a.Toselect1.2msto1.8ms–Youwillhear1shortbeep.
  Movethethrottlesticktocenter(between1.4and
  1.6ms).Thecontrollerwillbeep2times,indicatingyou
have set the program selection or leave in full throttle for
5 seconds to advance to the next selection.
 b.Toselect1.1msto1.9ms–Youwillhear2shortbeeps.
  Movethethrottlesticktocenter(between1.4and
  1.6ms).Thecontrollerwillbeep2times,indicatingyou
have set the program selection or leave in full throttle for
5 seconds to advance to the first selection again.
Programming Menu 5 – Start-Up Rate
Thedefaultsettingis0.25seconds.Thestart-uprateisthetimeittakes
to reach maximum motor speed. Changing the setting to 1 second can be
useful with power-fragile gear boxes.
1.Movethesticktocenter(between1.4and1.6ms)for5seconds,and
the controller will beep 5 times, indicating you are now in Menu 3.
2.Movethethrottlesticktofullthrottle(>1.7ms)positiontomake
 changestotheStart-upRateprogramming.
 a.Toselect.25second–Youwillhear1shortbeep.Move
  thethrottlesticktocenter(between1.4and1.6ms).The
  controllerwillbeep2times,indicatingyouhavesetthe
program selection or leave in full throttle for 5 seconds to
advance to the next selection.
 b.Toselect1second–Youwillhear2shortbeeps.Move
  thethrottlesticktocenter(between1.4and1.6ms).The
  controllerwillbeep2times,indicatingyouhavesetthe
program selection or leave in full throttle for 5 seconds to
advance to the first selection again.
Programming Menu 6 – PWM Switching Frequency
Thedefaultsettingis8kHz,whichshouldbeacceptableformostmotors.
If you have a low or very low inductance motor and know you need to use
ahigherPWMFrequency(refertothemanualincludedwiththemotor),
thenyoucanchangethesetting.Otherwise,werecommendleavingthe
default setting.
1.Movethesticktocenter(between1.4and1.6ms)for5seconds,and
the controller will beep 6 times, indicating you are now in Menu 6.
2.Movethethrottlesticktofullthrottle(>1.7ms)positiontomake
 changestothePWMSwitchingFrequencyprogramming.
 a.Toselect8kHzPWMFrequency–Youwillhear1shortbeep.
  Movethethrottlesticktocenter(between1.4and1.6ms).
  Thecontrollerwillbeep2times,indicatingyouhavesetthe
program selection or leave in full throttle for 5 seconds to
advance to the next selection.
 b.Toselect16kHzPWMFrequency–Youwillhear2short
  beeps.Movethethrottlesticktocenter(between1.4and
  1.6ms).Thecontrollerwillbeep2times,indicatingyou
have set the program selection or leave in full throttle for 5
seconds to advance to the next selection.
 c.Toselect32kHzPWMFrequency–Youwillhear3short
  beeps.Movethethrottlesticktocenter(between1.4and
  1.6ms).Thecontrollerwillbeep2times,indicatingyou
have set the program selection or leave in full throttle for 5
seconds to advance to the first selection again.
Programming Menu 7 – Operating Mode
ThedefaultsettingissettoNormal(airplane)Mode,whichislimitedto
astart-uprateof0.25or1second.Alternatively,theHeliModecanbe
selected which reduces the start-up rate to 5-seconds for the first start-up
andanystart-upafterthemotor/ESChasbeenstoppedformorethan5
seconds. This helps to prevent damaging the motor, gears or any other
components from an abrupt start-up when none of the parts are moving.
Anytimethemotor/ESChasbeenstoppedforlessthan5secondsinHeli
Mode, the start-up will be immediate. This allows power to be applied im-
mediately, such as when aborting an auto-rotation attempt or for any other
reason,tohelppreventacrash.Remember,youmustwaitmorethan5
secondsafterstoppingthemotor/ESCinorderforthe5secondstart-upto
occur again.
1.Movethesticktocenter(between1.4and1.6ms)for5seconds,and
the controller will beep 7 times, indicating you are now in Menu 7.
2.Movethethrottlesticktofullthrottle(>1.7ms)positiontomake
 changestotheOperatingModeprogramming.
 a.ToselectNormalMode–Youwillhear1short
  beep.Movethethrottlesticktocenter(between1.4and
  1.6ms).Thecontrollerwillbeep2times,indicatingyou
have set the program selection or leave in full throttle for
5 seconds to advance to the next selection.
 b.ToselectHeliMode–Youwillhear2
short beeps. Move the throttle stick to center (between