User's Manual

ManualsBrandsE F Johnson ManualsElectronicsUHF FM Handheld Transceiver Held-to-face

Table Of Contents

SAFETY INFORMATION
IMPORTANT OPERATING INFORMATION
QUICK REFERENCE GUIDE
FEATURES
- General Features
- LTR-Net Features
- LTR Features
- Conventional Features
CONTROLS AND DISPLAY
- Top Panel Controls
- Side Controls
- Display
- Front Panel Keys
BASIC OPERATION
- Power-Up Sequence
- Backlight Operation
- Setting Volume Levels
- System/Group Display Mode
- System and Group Select
- Keypad Disable
- Transceiver Lock
- Low Battery Indication
- Option Switches
- LTR-Net, LTR, and Conventional Operation
GENERAL FEATURES
- Bank Select
- Call Indicator
- Emergency Switch
- Encryption
- Home System/Group Select
- Option Select
- Power Select
- Proceed (Clear-To-Talk) Tone
- Receive-Only Groups
- Stealth Mode
- Time-Out Timer
- Tone Select
STANDARD GROUP CALLS
- General
- Placing a Standard Group Call
- Receiving a Standard Group Call
TELEPHONE CALLS
- General
- Placing Telephone Calls
- Receiving a Telephone Call
- Landside-Originate Telephone Calls
LTR-NET AUXILIARY CALLS
- General
- Placing LTR-Net Auxiliary Calls
- Receiving Auxiliary Calls
OPTION SWITCHES AND MENU MODE
- Option Switches
- Menu Mode
DIAL MODE
- Introduction
- Selecting Dial Mode
- Dialing a Number
- Sending the Number
- Storing Numbers in Memory
- Recalling Numbers From Memory
- Exiting Dial Mode
- Placing Calls Without Selecting Dial Mode
SYSTEM AND GROUP SCANNING
- General
- Scan List Programming
- Scan Delay and Continue Timers
- Transmitting In The Scan Mode
LTR-NET AND LTR FEATURES
- Transmit Inhibit
- Priority Calls
LTR-NET FEATURES
- LTR-Net Standard Calls
- LTR-Net Special Calls
- Busy Queuing
- Roaming
LTR FEATURES
- Standard Group Calls
- Telephone Calls
CONVENTIONAL FEATURES
- Squelch Adjust
- Monitoring Before Transmitting
- Transmit Disable On Busy
- Talk-Around
- Call Guard Squelch
MISCELLANEOUS
- Supervisory Tones
- LTR-Net Special Call Tones
- LTR Telephone Call Tones
- Display Messages
- Menu Mode Messages
- Rechargeable Battery Pack
- Speaking Into Microphone
- Operation At Extended Range
- Licensing
- Transceiver Service
INDEX
TABLE OF CONTENTS

SYSTEM AND GROUP SCANNING

Transmitting In The Scan Mode

General

When messages are received while scanning, programming deter-

mines if the selected system/group does not change, changes permanently

to the new system/group, or changes temporarily. This in turn affects the

system/group on which responses occur. The display always indicates the

system/group on which a call is received, but this may not be the system/

group on which a response occurs. The three programmable configura-

tions operate as follows:

Last Selected - Transmissions always occur on the system/group that

was selected manually by the SYS and GRP keys or automatically by

roaming. Therefore, to respond to a message that is not on the selected

system/group, the selected system/group must be changed using one of

these methods:

• Select the system/group of the call manually using the SYS and GRP

keys.

• Before scanning resumes, exit the scan mode by pressing FCN SCAN.

The system/group of the call then becomes the selected system/group

and it is not necessary to change it manually.

Last Received - The selected system/group changes to the system/group

of a call. Therefore, you can always respond to a call without having to

manually change the system/group. To return to the previously selected

system/group, it must be manually selected using the SYS and GRP keys.

Temporary Last Received - The system/group changes to the system/

group of a call for only the duration of the scan delay period (see

page 44.) Then when the delay expires and scanning resumes (if it is not

disabled), the selected system/group is again displayed. Therefore, you

can respond to a call without changing the selected system/group as long

as you do so before scanning resumes.