User's Manual

ManualsBrandsE F Johnson ManualsElectronicsUHF FM Handheld Transceiver Held-to-face

Table Of Contents

SAFETY INFORMATION
IMPORTANT OPERATING INFORMATION
QUICK REFERENCE GUIDE
FEATURES
- General Features
- LTR-Net Features
- LTR Features
- Conventional Features
CONTROLS AND DISPLAY
- Top Panel Controls
- Side Controls
- Display
- Front Panel Keys
BASIC OPERATION
- Power-Up Sequence
- Backlight Operation
- Setting Volume Levels
- System/Group Display Mode
- System and Group Select
- Keypad Disable
- Transceiver Lock
- Low Battery Indication
- Option Switches
- LTR-Net, LTR, and Conventional Operation
GENERAL FEATURES
- Bank Select
- Call Indicator
- Emergency Switch
- Encryption
- Home System/Group Select
- Option Select
- Power Select
- Proceed (Clear-To-Talk) Tone
- Receive-Only Groups
- Stealth Mode
- Time-Out Timer
- Tone Select
STANDARD GROUP CALLS
- General
- Placing a Standard Group Call
- Receiving a Standard Group Call
TELEPHONE CALLS
- General
- Placing Telephone Calls
- Receiving a Telephone Call
- Landside-Originate Telephone Calls
LTR-NET AUXILIARY CALLS
- General
- Placing LTR-Net Auxiliary Calls
- Receiving Auxiliary Calls
OPTION SWITCHES AND MENU MODE
- Option Switches
- Menu Mode
DIAL MODE
- Introduction
- Selecting Dial Mode
- Dialing a Number
- Sending the Number
- Storing Numbers in Memory
- Recalling Numbers From Memory
- Exiting Dial Mode
- Placing Calls Without Selecting Dial Mode
SYSTEM AND GROUP SCANNING
- General
- Scan List Programming
- Scan Delay and Continue Timers
- Transmitting In The Scan Mode
LTR-NET AND LTR FEATURES
- Transmit Inhibit
- Priority Calls
LTR-NET FEATURES
- LTR-Net Standard Calls
- LTR-Net Special Calls
- Busy Queuing
- Roaming
LTR FEATURES
- Standard Group Calls
- Telephone Calls
CONVENTIONAL FEATURES
- Squelch Adjust
- Monitoring Before Transmitting
- Transmit Disable On Busy
- Talk-Around
- Call Guard Squelch
MISCELLANEOUS
- Supervisory Tones
- LTR-Net Special Call Tones
- LTR Telephone Call Tones
- Display Messages
- Menu Mode Messages
- Rechargeable Battery Pack
- Speaking Into Microphone
- Operation At Extended Range
- Licensing
- Transceiver Service
INDEX
TABLE OF CONTENTS

GENERAL FEATURES

Home System/Group Select

To select the preprogrammed Home system/group, simply press the

FCN HOME. The Home system/group is then displayed and it becomes

the selected system/group. If no home system/group has been

programmed, this function is not available. A different home system/

group can be programmed for each bank.

Option Select

The Auxiliary option switch or OPTION menu parameter can be

used to control an accessory that may have been installed by your system

operator. The enabled condition is indicated by in the display.

Power Select

High and low transmit power output is selectable if the “TX

POWER” menu parameter is available. Select either “LO POWER” or

“HI POWER” as described on page 36. When low power output is

selected manually or automatically, “

L” is indicated in the display (see

page 13). Turning power off and then on again does not change the

selected power output level. Selecting low power may increase battery

life and decrease range, and selecting high power may cause the opposite

to occur. The low power mode is automatically selected during a low

battery condition (see page 23).

Proceed (Clear-To-Talk) Tone

This is a short tone that sounds shortly after the PTT switch is

pressed to indicate that the radio system has been accessed and speaking

can begin. This tone can be programmed to be a single or distinctive (3-

beep) tone. With encrypted calls, a special double beep sounds.

This tone always sounds with LTR-Net and LTR standard calls if

tones are enabled by the TONES menu parameter (see “Tone Select” on

page 29) or system operator programming. It can also be programmed to