User's Manual
Table Of Contents
- Radio Overview
- Controls & Display
- General Operation
- 3.1 Basic Operation
- 3.1.1 Turning Power ON and Setting Volume
- 3.1.2 Persistent Settings
- 3.1.3 Power-Up Password
- 3.1.4 Speaking into the Microphone
- 3.1.5 Display Backlight Control
- 3.1.6 Display Viewing Angle & Contrast Adjust (Standard Control Head Only)
- 3.1.7 Zone / Channel Display and Select
- 3.1.8 Setting Squelch Control
- 3.1.9 Zone Edit
- 3.1.10 Transmit Disable
- 3.1.11 Operation At Extended Range
- 3.1.12 Preventing Vehicle Battery Discharge
- 3.1.13 Cleaning the Control Head
- 3.1.14 Radio Service
- 3.2 Single Touch
- 3.2.1 Single Touch Buttons
- 3.2.2 Detailed Single Touch Operation
- 3.2.2.1 Conventional Unit Call
- 3.2.2.2 Conventional Call Alert
- 3.2.2.3 Conventional Status
- 3.2.2.4 Conventional Message
- 3.2.2.5 P25 Unit Call
- 3.2.2.6 P25 Call Alert
- 3.2.2.7 P25 Status
- 3.2.2.8 P25 Interconnect
- 3.2.2.9 SNSZ Unit Call
- 3.2.2.10 SNSZ Call Alert
- 3.2.2.11 SNSZ Status
- 3.2.2.12 SNSZ Message:
- 3.2.2.13 SNSZ Interconnect:
- 3.3 Radio Inhibit
- 3.4 Setting Squelch
- 3.5 Operating Modes
- 3.1 Basic Operation
- Radio Wide Features
- 4.1 Option Buttons
- 4.2 Menu Mode
- 4.3 Time-Out Timer
- 4.4 Home Channel Select
- 4.5 Power Output Select
- 4.6 Alert Tone Select
- 4.7 Ignition Power Down Duration
- 4.8 Horn Alert
- 4.9 Microphone Off-Hook Detect
- 4.10 Surveillance Mode
- 4.11 Public Address
- 4.12 Scanning
- 4.13 Scan Lists
- 4.14 Over the Air Programming
- 4.15 Over the Internet Programming
- 4.16 Auto / Unmute
- 4.17 Location Services
- 4.18 Emergency Alarm Receive Indicator
- 4.19 Kiosk Mode
- 4.20 Analog Noise Reduction
- Conventional Mode Features
- 5.1 Monitoring Before Transmitting
- 5.2 Monitor Mode
- 5.3 Busy Channel Lockout
- 5.4 Call Guard Squelch
- 5.5 Penalty Timer
- 5.6 Conversation Timer
- 5.7 Repeater Talk-Around
- 5.8 Displaying Transmit / Receive Frequency
- 5.9 Emergency Alarm and Call
- 5.10 Conventional Mode Channel Scanning
- 5.11 Standard Conventional Calls
- 5.12 DTMF / ANI Signaling
- 5.13 Project 25 Mode Features
- 5.13.1 Digital Unit ID
- 5.13.2 Talkgroup ID
- 5.13.3 Network Access Code (NAC)
- 5.13.4 EFJohnson System Out-of-Range Indicator
- 5.13.5 EFJohnson System Automatic Registration
- 5.13.6 P25 Group Calls
- 5.13.7 P25 Unit Calls
- 5.13.8 P25 Conventional Telephone Calls
- 5.13.9 Call Alert
- 5.13.10 Call History
- 5.13.11 Messaging
- 5.13.12 Status Messaging
- 5.13.13 P25 Packet Data
- 5.14 Keypad Programming
- 5.15 Text Messaging
- SMARTNET / SmartZone / P25 Trunked Features
- 6.1 Analog and Digital Operation
- 6.2 Viewing Unit ID
- 6.3 Standard Group Calls
- 6.4 Unit Calls
- 6.5 Telephone Calls
- 6.6 Call Alert
- 6.7 Messaging
- 6.8 Sending Status Conditions
- 6.9 Emergency Alarm and Call
- 6.10 Failsoft Operation
- 6.11 SMARTNET / SmartZone / P25 Trunking Scanning Features
- 6.12 Dynamic Regrouping
- 6.13 P25 Radio Unit Monitor
- 6.14 SmartZone and P25 Trunking Unique Features
- 6.14.1 Busy Override
- 6.14.2 Site Trunking
- 6.14.3 Determining Current Site and Searching for a New Site
- 6.14.4 Locking / Unlocking a Site
- 6.14.5 Auto Site Search
- 6.14.6 P25 Wide Area Scan
- 6.14.7 Normal P25 and SmartZone Control Channel Hunt
- 6.14.8 Talkgroup Steering through System Access Permissions
- 6.14.9 Radio Information
- 6.14.10 Current Software version in the radio
- 6.15 P25 Trunking System Single Touch
- 6.16 P25 Messaging
- Secure Communication (Encryption)
- Data Features
- Tones & Error Messages
- Service Information
Draft 02 - Sep 1 2015
6-12 Viking Mobile Radio Operating Manual
SMARTNET / SmartZone / P25 Trunked Features
6.7 Messaging
The messaging feature allows preprogrammed messages to be sent to your dispatcher. Up
to 255 messages can be preprogrammed, and they are identified by an alias. Messages are
sent as follows:
1 Momentarily press the Message option switch, soft button (Lightning Control Head
only), or select the menu parameter. The alias of the last message sent is displayed.
2 If required, rotate the Select switch to display the desired message. Then send the
message by momentarily pressing the PTT or Select switch. A single beep sounds when
the Select switch is pressed (if that option is selected). One of the following then
occurs:
- If five beeps sound and “ACK RECVD” (Standard Control Head) or “Ack Received”
(Lightning Control Head) is displayed, the message was received and automatically
acknowledged by the system.
- If after five tries the message is not acknowledged, a tone sounds and “NO ACK”
(Standard Control Head) or “No Acknowledge” (Lightning Control Head) is
displayed.
Note Only the message number assigned to the alias is sent– not the actual text of the alias. For
example, If MSG 1 is assigned to alias “In Service”, “MSG 1” is sent– not “In Service”.
6.7.1 P25 Messaging
There is a two menu design with this feature which allows the user to select a Unit ID and
then a Message. To exit the menu, the Message button on the radio or the back button can
be pressed. However, if the user is in the second menu (selecting the Message to send), the
back button will take them back to the menu that allows them to select a Unit ID. From
there, one more press of the back button exits the menu.
A P25 Message Alias list may be programmed for this feature. Also a new menu button,
soft button (Lightning Control Head only), and an alias for Message may be programmed.
Sending a Message
To send Messages from one radio to another, the user must select a Unit ID and a
Message. The Unit ID can either be selected from the Unit Call list programmed, or may
be entered by the user. To select a Unit ID from the Unit Call list, press the button or soft
button assigned to Message on the radio or select “ID List” from the Message menu. To
enter a Unit ID, press and hold the button or soft button assigned to Message on the radio
or select “Enter ID” from the Message menu. Once the Unit ID has been selected, the radio
takes the user to a list which displays the Messages that have been programmed in the
Message List. A selection (which attempts to send the Message from this point) can be