User's Manual
Table Of Contents
- Features
- Controls and Display
- General Operation
- Radio-wide Features
- 4.1 Viewing Radio Information
- 4.2 Option Keys / Buttons
- 4.3 Feature Enable / Disable
- 4.4 Menu Mode
- 4.5 Function Recall
- 4.6 Time-Out Timer
- 4.7 Home Channel Select
- 4.8 Power Output Select
- 4.9 Alert Tone Select
- 4.10 Surveillance Mode
- 4.11 Scanning
- 4.12 Global Positioning System (GPS)
- 4.13 Radio Service
- 4.14 Fire Ground Mode
- Conventional Mode Features
- 5.1 Monitoring Before Transmitting
- 5.2 Monitor Mode
- 5.3 Busy Channel Lockout
- 5.4 Call Guard Squelch
- 5.5 Penalty Timer
- 5.6 Conversation Timer
- 5.7 Repeater Talkaround
- 5.8 Displaying Transmit / Receive Frequency
- 5.9 Emergency Alarm and Call
- 5.10 Conventional Mode Scanning
- 5.11 Standard Conventional Calls
- 5.12 ANI Signaling Options
- 5.13 Project 25 Mode Features
- 5.13.1 Digital Unit ID
- 5.13.2 Talkgroup ID
- 5.13.3 Network Access Code
- 5.13.4 Out of Range (EFJohnson Conventional) Indication
- 5.13.5 Automatic (EFJohnson Conventional) Registration
- 5.13.6 P25 Group Calls
- 5.13.7 Talkgroup Scan
- 5.13.8 P25 Unit Calls
- 5.13.9 P25 Conventional Telephone Calls
- 5.13.10 Call Alert
- 5.13.11 Call History
- 5.13.12 Messaging
- 5.13.13 Status Messaging
- 5.13.14 P25 Packet Data
- 5.14 Keypad Programming
- 5.15 Text Messaging
- 5.16 Fire Ground Mode
- SmartNet / SmartZone / P25 Trunked Features
- 6.1 Analog and Digital Operation
- 6.2 Standard Group Calls
- 6.3 Private (Unit-To-Unit) Calls
- 6.4 Telephone Calls
- 6.5 Call Alert
- 6.6 Messaging
- 6.7 Sending Status Conditions
- 6.8 Emergency Alarm and Call
- 6.9 Failsoft Operation
- 6.10 SmartNet / SmartZone / P25 Trunked Scanning Features
- 6.11 Dynamic Regrouping
- 6.12 SmartZone and P25 Trunking Unique Features
- 6.13 Zone Password
- Messages
- Secure Communication (Encryption)
- Data Features
- Service Information
2-2 Viking Portable 600 Radio Operating Manual
Controls and Display
Note The appearance of the 51FIRE Viking III radios are identical to the Viking VP600 Model
III radios except for the yellow casing for the 51FIRE radios.
Microphone - The microphone is located behind the small opening shown in Figure 2.1.
For best results, hold the radio 2-3 inches from you mouth and speak at a normal
conversational level. Do not shout since it distorts your voice and does not increase range.
Make sure that the PTT (push-to-talk) switch is pressed before you begin to speak and
released as soon as the message is complete.
Display - This is a graphical LCD (Liquid Crystal Display). The display backlight can be
programmed to turn on when any key/button is pressed (or pressed and held, depending
upon programming), or when the Backlight option button is pressed or menu parameter
selected (see Section 3.5, "Backlight").
Up/Down Buttons- Select zones when multiple zones are programmed (see Section 3.3,
"Zone and Channel Select"). Pressing the up button selects the next higher number and
pressing the down button selects the next lower number. These buttons also provide up/
down select in the menu mode and in other modes when up/down select is required.
<F1> - In menu mode (see Section 4.4, "Menu Mode"), functions as a step back and exit
button. If menu mode is not used, it is a programmable option button.
<F2> - Selects the menu mode when that mode is enabled by programming. Also
functions as an Enter or Select button in the menu and other modes. If menu mode is not
used, it is a programmable option button.
<F3>, <F4> - Programmable option buttons. Function Button and Clear/Cancel <F3>
exit the feature without saving. Menu/Select (F4) exits the feature and saves changes.
DTMF Keypad - The full keypad DTMF models include the 12 keys required to dial
telephone and unit ID numbers.
Speaker - The radio speaker is located near the bottom of the front panel. When a speaker/
microphone is used, it is automatically detected when the Opt Sel 1 line of the accessory
connector is pulled low. The logic then automatically disables the internal speaker.
Preliminary Draft 3/9/12