User's Manual
Table Of Contents
- Safety Information
- General
- Controls And Display
- General Operation
- Radio Wide Features
- Conventional Features
- 5.1 Monitoring Before Transmitting
- 5.2 Monitor Mode
- 5.3 Busy Channel Lockout
- 5.4 Call Guard Squelch
- 5.5 Penalty Timer
- 5.6 Conversation Timer
- 5.7 Repeater Talk-Around
- 5.8 Displaying Transmit/Receive Frequency
- 5.9 Emergency Alarm and Call
- 5.10 Conventional Mode Scanning
- 5.11 Standard Conventional Calls
- 5.12 DTMF/ANI Signaling
- 5.13 Single Tone Encoder
- 5.14 MDC1200 Compatibility
- 5.15 Project 25 Mode Features
- 5.16 Keypad Programming
- SMARTNET/SmartZone/P25 Trunked Features
- 6.1 Analog and Digital Operation
- 6.2 Viewing Unit ID
- 6.3 Standard Group Calls
- 6.4 Private (Unit-To-Unit) Calls
- 6.5 Telephone Calls
- 6.6 Call Alert
- 6.7 Messaging
- 6.8 Sending Status Conditions
- 6.9 Emergency Alarm and Call
- 6.10 Failsoft Operation
- 6.11 SMARTNET/SmartZone/P25 Trunked Scanning Features
- 6.12 Dynamic Regrouping
- 6.13 SmartZone and P25 Trunking Unique Features
- 6.13.1 Busy Override
- 6.13.2 Site Trunking
- 6.13.3 Determining Current Site and Searching For a New Site
- 6.13.4 Locking/Unlocking a Site
- 6.13.5 ZoneFail Site Lock
- 6.13.6 P25 Wide Area Scan
- 6.13.7 Normal P25 and SmartZone Control Channel Hunt
- 6.13.8 Talkgroup Steering Via System Access Permissions
- 6.13.9 P25 Wide Area Scan
- Miscellaneous
- Determining Available Options
- 5300 ES Mobile Firmware Versions
- Password Description
- Secure Communication (Encryption)
Draft
December 2006 5300 ES Series Mobile Radio Operating Manual -13
6.11.1 Priority Talk Group Sampling
One talk group in the scan list can be designated a priority talk group by programming or
it can be the selected talk group. When scanning, messages on a non-priority talk group
are interrupted by messages on the priority talk group. Priority scanning must also be
supported at the system level for it to occur as programmed in the radio.
6.11.2 Scan List Editing and Selection
SMARTNET/SmartZone and P25 Trunked scan lists are user programmable if the SCN
ED option switch is programmed. The procedure is described in
Section 4.12.1.
With SMARTNET/SmartZone and P25 trunked operation, each channel (talk group) can
be programmed to select one of the programmed scan lists or so scanning is disabled (No
List). In addition, each channel can be programmed so that scanning is automatically
enabled (Auto Scan) when it is selected.
If the SN LIST option switch is programmed, the list that is selected by all talk and
announcement groups in the current system can be temporarily changed by the user as
follows. Also selectable if desired is “No List” (scanning disabled) or “Programmed”
(default list). The programmed default list is automatically reselected at power up.
Proceed as follows to temporarily change the currently selected scan list:
1 With scanning disabled (the rotating icon is not indicated in the right status display),
press the SN LIST option switch.
2 The currently selected list is displayed as “List x”, with “x” the currently selected list.
To exit without changing the selected list, simply press the SN LIST option switch
again.
3 To select another list, “Programmed”, or “No List”, rotate the Select switch. When the
desired list is displayed, select it and exit this mode by pressing the Scan List option
switch again.
6.12 Dynamic Regrouping
The dynamic regrouping feature allows a dispatcher to change the current talk group or
switch mobiles to a predefined regrouping channel to receive an important message. When
the console issues a regroup order, the radio switches to the preprogrammed regroup talk
group.
If the Cancel Dynamic Regrouping option switch is programmed, it can be pressed to exit
the dynamic regrouping mode.