User's Manual
Table Of Contents
- Safety Information
- General
- Controls And Display
- General Operation
- Radio Wide Features
- Conventional Features
- 5.1 Monitoring Before Transmitting
- 5.2 Monitor Mode
- 5.3 Busy Channel Lockout
- 5.4 Call Guard Squelch
- 5.5 Penalty Timer
- 5.6 Conversation Timer
- 5.7 Repeater Talk-Around
- 5.8 Displaying Transmit/Receive Frequency
- 5.9 Emergency Alarm and Call
- 5.10 Conventional Mode Scanning
- 5.11 Standard Conventional Calls
- 5.12 DTMF/ANI Signaling
- 5.13 Single Tone Encoder
- 5.14 MDC1200 Compatibility
- 5.15 Project 25 Mode Features
- 5.16 Keypad Programming
- SMARTNET/SmartZone/P25 Trunked Features
- 6.1 Analog and Digital Operation
- 6.2 Viewing Unit ID
- 6.3 Standard Group Calls
- 6.4 Private (Unit-To-Unit) Calls
- 6.5 Telephone Calls
- 6.6 Call Alert
- 6.7 Messaging
- 6.8 Sending Status Conditions
- 6.9 Emergency Alarm and Call
- 6.10 Failsoft Operation
- 6.11 SMARTNET/SmartZone/P25 Trunked Scanning Features
- 6.12 Dynamic Regrouping
- 6.13 SmartZone and P25 Trunking Unique Features
- 6.13.1 Busy Override
- 6.13.2 Site Trunking
- 6.13.3 Determining Current Site and Searching For a New Site
- 6.13.4 Locking/Unlocking a Site
- 6.13.5 ZoneFail Site Lock
- 6.13.6 P25 Wide Area Scan
- 6.13.7 Normal P25 and SmartZone Control Channel Hunt
- 6.13.8 Talkgroup Steering Via System Access Permissions
- 6.13.9 P25 Wide Area Scan
- Miscellaneous
- Determining Available Options
- 5300 ES Mobile Firmware Versions
- Password Description
- Secure Communication (Encryption)
Draft
-18 5300 ES Series Mobile Radio Operating Manual December 2006
2 To clear or ignore the page, press any option switch. If the PTT switch is pressed, a
group call is placed on the selected channel.
3 To answer the page as a unit call (see Section 5.15.5), press the CALL (Private/Unit)
option switch and the alias of the mobile paging you is displayed. Press the PTT switch
and respond. One of the following conditions then occur:
• If the mobile being called is on the air, ringing is heard until the called party answers
or for 20 seconds, whichever occurs first. If no answer occurs within 20 seconds, a
continuous tone sounds and “NO ANS” is displayed.
• If the mobile being called is not on the air, a continuous tone is heard instead of
ringing and “NO ACK” is displayed.
4 When the call is finished or if it could not be completed for some reason, end it by
pressing the Unit Call option switch or the F1 (Exit) key.
To Initiate a Page:
1 With a P25 conventional channel selected, momentarily press the ALERT (Call Alert)
option switch. The alias of the last ID called is displayed.
2 If required, rotate the Select switch to display the desired mobile. The alias of each
number is displayed.
3 Press the PTT switch and one of the following occur:
• If five beeps sound, the system received the page and the paged mobile is on the air
and received it. The page mode is automatically exited.
• If the system received the page but the called mobile is not on the air, a single beep
sounds and “NO ACK” is displayed six seconds after the PTT switch is pressed. Auto
exit then occurs.
5.15.8 Messaging
The messaging feature allows preprogrammed messages to be sent to a dispatcher on P25
channels. Up to 16 messages can be preprogrammed, and they are identified by an alias. If
a MSG (Message) option switch is programmed, messages are sent as follows:
1 Momentarily press the MSG option switch. The alias of the last message sent is
displayed.
2 If required, rotate the Select switch to display the desired message. Then send the
message by momentarily pressing the PTT or Select switch. One of the following
events then occurs:
• If five beeps sound and “ACK RECVD” is displayed, the message was received and
automatically acknowledged by the system.