User's Manual
Table Of Contents
- Safety Information
- General
- Controls And Display
- General Operation
- Radio Wide Features
- Conventional Features
- 5.1 Monitoring Before Transmitting
- 5.2 Monitor Mode
- 5.3 Busy Channel Lockout
- 5.4 Call Guard Squelch
- 5.5 Penalty Timer
- 5.6 Conversation Timer
- 5.7 Repeater Talk-Around
- 5.8 Displaying Transmit/Receive Frequency
- 5.9 Emergency Alarm and Call
- 5.10 Conventional Mode Scanning
- 5.11 Standard Conventional Calls
- 5.12 DTMF/ANI Signaling
- 5.13 Single Tone Encoder
- 5.14 MDC1200 Compatibility
- 5.15 Project 25 Mode Features
- 5.16 Keypad Programming
- SMARTNET/SmartZone/P25 Trunked Features
- 6.1 Analog and Digital Operation
- 6.2 Viewing Unit ID
- 6.3 Standard Group Calls
- 6.4 Private (Unit-To-Unit) Calls
- 6.5 Telephone Calls
- 6.6 Call Alert
- 6.7 Messaging
- 6.8 Sending Status Conditions
- 6.9 Emergency Alarm and Call
- 6.10 Failsoft Operation
- 6.11 SMARTNET/SmartZone/P25 Trunked Scanning Features
- 6.12 Dynamic Regrouping
- 6.13 SmartZone and P25 Trunking Unique Features
- 6.13.1 Busy Override
- 6.13.2 Site Trunking
- 6.13.3 Determining Current Site and Searching For a New Site
- 6.13.4 Locking/Unlocking a Site
- 6.13.5 ZoneFail Site Lock
- 6.13.6 P25 Wide Area Scan
- 6.13.7 Normal P25 and SmartZone Control Channel Hunt
- 6.13.8 Talkgroup Steering Via System Access Permissions
- 6.13.9 P25 Wide Area Scan
- Miscellaneous
- Determining Available Options
- 5300 ES Mobile Firmware Versions
- Password Description
- Secure Communication (Encryption)
Draft
December 2006 5300 ES Series Mobile Radio Operating Manual -5
Proceed as follows to select channels using this mode:
1 Enable the direct Channel Select mode by pressing the Channel Select option switch.
The alias and sequential number of the current channel are alternately displayed.
2 Select the desired channel using the Up/Down keys or directly enter it using the 0-9
keys. If using the 0-9 keys, the radio attempts to display the entered number after the
third digit is entered or approximately two seconds after the last key is pressed.
3 To exit this mode and select the entered channel, press the Channel Select switch again.
This mode is also exited automatically without changing the channel after
approximately one minute of no activity.
Note The Channel Select function should probably not be assigned to a number key because
pressing that key to select a channel then exits the select mode.
Other features of this mode are as follows:
• When using the Up/Down keys, wrap-around to the lowest zone/channel occurs after
the last channel in the highest programmed zone is displayed and vice versa. For
example, if Zone 1/Channel 5 is the highest programmed channel, wrap-around occurs
after Zone 1/Channel 16 is displayed.
• When an unprogrammed channel is displayed, the sequential channel number and
“Unprogramd” are alternately displayed.
• If an invalid channel number is entered using the 0-9 keys, or the Channel Select option
switch is pressed with “Unprogramd” displayed, an error tones sounds, “Invalid” is
briefly displayed, and the displayed channel does not change.
3.5 Setting Squelch Control
This radio does not have a squelch control. The squelch level is preset and usually does
not require readjustment. However, if the squelch level needs to be changed on a
conventional analog channel, it can be changed using keypad programming if available
(see Section 5.17 on page 36).
3.6 Transmit Disable
Transmitting can be disabled on each conventional, SMARTNET, SmartZone, and P25
Trunked channel so that the channel is monitor-only. When transmitting is attempted on a
receive-only channel, “Rx Only” is displayed and an error tone sounds.