User's Manual
Table Of Contents
- Safety Information
- General
- Controls And Display
- General Operation
- Radio Wide Features
- Conventional Features
- 5.1 Monitoring Before Transmitting
- 5.2 Monitor Mode
- 5.3 Busy Channel Lockout
- 5.4 Call Guard Squelch
- 5.5 Penalty Timer
- 5.6 Conversation Timer
- 5.7 Repeater Talk-Around
- 5.8 Displaying Transmit/Receive Frequency
- 5.9 Emergency Alarm and Call
- 5.10 Conventional Mode Scanning
- 5.11 Standard Conventional Calls
- 5.12 DTMF/ANI Signaling
- 5.13 Single Tone Encoder
- 5.14 MDC1200 Compatibility
- 5.15 Project 25 Mode Features
- 5.16 Keypad Programming
- SMARTNET/SmartZone/P25 Trunked Features
- 6.1 Analog and Digital Operation
- 6.2 Viewing Unit ID
- 6.3 Standard Group Calls
- 6.4 Private (Unit-To-Unit) Calls
- 6.5 Telephone Calls
- 6.6 Call Alert
- 6.7 Messaging
- 6.8 Sending Status Conditions
- 6.9 Emergency Alarm and Call
- 6.10 Failsoft Operation
- 6.11 SMARTNET/SmartZone/P25 Trunked Scanning Features
- 6.12 Dynamic Regrouping
- 6.13 SmartZone and P25 Trunking Unique Features
- 6.13.1 Busy Override
- 6.13.2 Site Trunking
- 6.13.3 Determining Current Site and Searching For a New Site
- 6.13.4 Locking/Unlocking a Site
- 6.13.5 ZoneFail Site Lock
- 6.13.6 P25 Wide Area Scan
- 6.13.7 Normal P25 and SmartZone Control Channel Hunt
- 6.13.8 Talkgroup Steering Via System Access Permissions
- 6.13.9 P25 Wide Area Scan
- Miscellaneous
- Determining Available Options
- 5300 ES Mobile Firmware Versions
- Password Description
- Secure Communication (Encryption)
Draft
December 2006 5300 ES Series Mobile Radio Operating Manual -3
10.2 Password Description
10.2.1 User (Power-On) Passwords
When a User Password is enabled, it must be entered each time radio power is turned on.
Up to four different User Passwords (User 1/User 2/User 3/User 4) can be programmed.
Currently, the same radio features are enabled for each. Entering any User Password at
power up enables normal radio operation.
10.2.2 Download/Upload Passwords
Separate Download (write) and Upload (read) passwords can be programmed to prevent
unauthorized downloading or uploading of radio programming parameters. When one or
both of these passwords are used, the proper password must be entered to perform the
operation. A “User” password is not required to upload or download parameters.
10.2.3 Master Password
The Master Password overrides all the preceding passwords. It can be used by a system
administrator as a “pass key” to a password controlled function or to change a lost or
inadvertently changed password. Master passwords are set up and changed the same as the
other passwords. It does not override the following Zone Password.
10.3 Zone Password
Note The programming and usage of this password has not changed. It is independent from the
preceding passwords, and programmed in the Zone > Edit Zones and Channels screen.
A zone password can be programmed with the 5300 ES mobile. It prevents unauthorized
reprogramming of zones by keypad programming. When this password is used, it must be
entered before system or channel parameters in that zone can be changed. The zone
password is programmed in the Edit Zones and Channels screen. This screen is displayed
by clicking the Edit Zone button on the Zone screen.
A different password can be programmed for each zone. When a password protected zone
is selected, “PASSWORD” is flashed the first time an attempt is made to select a system
or channel parameter in that zone. Each digit of the password is then entered as previously
described. The password is always eight digits long, and after the eighth digit is entered,
system and channel parameters for that zone can be reprogrammed normally.