5300 ES Series Mobile Radio Operating Manual 700 / 800 MHz Project 25 Conventional and Trunked Analog and Digital Conventional SMARTNET®/SmartZone® 13.
Copyright © 2007-2008 by EFJohnson The EFJohnson logo, PC Configure™, Trunked IP25™, and Call Guard® are trademarks of EFJohnson. All other company and/or product names used in this manual are trademarks and/or registered trademarks of their respective manufacturers. Information in this manual is subject to change without notice.
300 ES Series Mobile Radio Operating Manual March 2008 Table of Contents Safety Information 1 General xi 1-1 General Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Conventional Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 SMARTNET / SmartZone Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents (continued) SMARTNET / SmartZone Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P25 Trunked Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Systems, Channels, and Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents (continued) Monitor Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Busy Channel Lockout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Call Guard Squelch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Call Guard Squelch Enable / Disable . . . . . . .
Table of Contents (continued) Zone Change Parameter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Channel Change Parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Channel Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents (continued) P25 Wide Area Scan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-20 7 Miscellaneous 7-1 Supervisory Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 Error Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents (continued) Encryption Key Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5 Encryption Icon Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5 Clear / Secure Strapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transmit Mode Options. . . . . . . . . . . . . . . . . . . . . . . . . . .
List of Figures Figure 2.1 2.2 2.3 5.1 10.1 March 2008 Page Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Rear Panel Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Front Panel Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 5300 ES Keypad Programming Menu Flowchart . . . . . . . . . . .
List of Figures (continued) Figure viii 5300 ES Series Mobile Radio Operating Manual Page March 2008
List of Tables Table 3.1 3.2 3.3 3.4 4.1 March 2008 Page Initial Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10 RF Test Mode Frequencies (MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11 RF Test Mode Environments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11 Control Top and Keypad Test Mode Display Messages . . . . . . . . . . . . . . . . .
List of Tables (continued) Table x 5300 ES Series Mobile Radio Operating Manual Page March 2008
Safety Information Section0 RF Energy Exposure Awareness and Control Information, and Operational Instructions for FCC Occupational Use Requirements Before using your mobile two-way radio, read this important RF energy awareness and control information and operational instructions to ensure compliance with the FCC’s RF exposure guidelines.
Safety Information Your EFJohnson two-way radio has a RF exposure product label. Also, your EFJohnson user manual, or product manual, or separate safety booklet includes information and operating instructions required to control your RF exposure and to satisfy compliance requirements.
Safety Information Transmit only when people outside the vehicle are at least the recommended minimum lateral distance away, as shown in Table 1, from a properly installed according to installation instructions, externally-mounted antenna. Note The following table lists the recommended minimum lateral distance for bystanders in an uncontrolled environment from transmitting types of antennas (i.e.
Safety Information Approved Accessories This radio has been tested and meets the FCC RF exposure guidelines when used with the EFJohnson accessories supplied or designated for this product. Use of other accessories may not ensure compliance with the FCC’s RF exposure guidelines, and may violate FCC regulations. For a list of EFJohnson approved accessories, refer to the radio service manual or contact the EFJohnson Company as follows.
S E C T I O N 1 General Section1 The availability of many of the following features is controlled by field programming and by what options were ordered. For example, encryption and some operating modes are optional. See the EFJohnson product description and Section 8 for further details. 1.
General • Emergency calls for high priority system access • Priority (standard) and Radio Wide scan modes with user programmable scan lists • User selectable high and low power output • Surveillance mode • Time-out timer • Power up password to prevent unauthorized use. • Programmable and user adjustable tone volume • Programmable minimum volume level • Operates on both wide and narrow band channels 1.
General • Predefined status conditions (up to eight) can be sent to a dispatcher (P25 mode only) • OTAR (Over-The-Air-Rekeying) compatible (P25 channels only). • Keypad programming with password access (Federal Government users only) 1.
General • Emergency alarms to alert a dispatcher of emergency conditions • Emergency calls for high priority system access • Failsoft operation on a predefined conventional channel if trunked system fails • Priority group calls detected while listening to other group calls when scanning • Call Alert™ (send and receive pages) • Predefined status conditions (up to eight) can be sent to a dispatcher • Dynamic regrouping (dispatcher can automatically gather users on a channel to receive a message) • Roaming •
S E C T I O N 2 Controls And Display Section2 2.1 Front Panel Controls Figure 2.1 shows the controls for the 5300 ES Mobile radio. Figure 2.1 Front Panel Controls Programmable Buttons Display Multi-function Indicator Microphone Connection ON-OFF/Volume Select Switch Speaker ON-OFF /Volume - Pressing this control turns power ON and OFF, and rotating it sets the volume level. Select Switch - This switch can be pressed or rotated.
Controls And Display Multi-function Indicator - This is a two-color LED that indicates the following: Red (constant) - Transmitter keyed (PTT switch pressed). Green (constant) - Busy condition (carrier detected in receive mode). Note This indicator is disabled when the Surveillance mode is programmed (see Section 4.10).
Controls And Display Siren Control (Not Shown) - An optional yellow/orange connector similar to the accessory jack for connecting the optional siren controller. 2.3 Display Figure 2.3 shows the front panel display. Figure 2.
Controls And Display A “P” in the left position indicates that the selected conventional channel is a priority channel (first priority with dual priority). A “2” in the left position indicates that the selected conventional channel is a second priority channel. This rotating clock-like symbol in the right position indicates that scanning is enabled. When beneath Button 1, indicates that the scan list edit or keypad programming mode is selected (see Section 4.13 or Section 5.14).
S E C T I O N 3 General Operation Section3 This section provides general information about the operation of the 5300 ES Mobile radios. The following information is discussed: • Turning Power ON/OFF and Setting the Volume • Passwords • Backlight controls and display viewing • Displaying and Selecting Zones/Channels • Setting Squelch Control • Transmit Disable • Radio Operating Modes • Radio Tune Test Mode 3.
General Operation • Last Zone/Home Channel • Home Zone/Last Channel • Home Zone/Home Channel The Home Zone and Channel are pre programmed. With the “Last Zone”/“Home Channel” configuration, the programmed home channel number of the last active zone is selected. If this channel number is not programmed in the active zone, “UNPROGRAMD” is displayed. If the Radio ID feature is enabled, the radio will display the Radio ID alias in place of the Self Test message during startup.
General Operation 3.2 Power-Up Password The power-up password feature prevents unauthorized use of the radio by requiring that an eight-digit password be entered to make it operational. This feature is enabled or disabled by programming. When it is enabled, “ENTER PSWD” is briefly displayed when power is turned on, the eight-digit numeric password must be entered by pressing and rotating the Select switch. If an incorrect password is entered, “INCORRECT” is displayed and it must be re-entered.
General Operation 3.4.1 Zone / Channel Display The selected zone and channel numbers are displayed by the zone and channel displays shown in the following illustration. In addition, the selected zone identification (alias) is displayed in the alphanumeric display area when the zone select mode is enabled, and the channel alias is displayed when the channel select mode is enabled (see following). Channel alias can be a combination of zone and channel aliases.
General Operation 3.4.3 Direct Channel Select The direct Channel Select feature is available with the Handheld Control Unit (HHC) only, and if the Channel Select option switch parameter is programmed. This feature allows channels to be directly selected using the HHC numeric keys or Up/Down switch. For direct selection purposes, channels are numbered sequentially starting with the lowest zone.
General Operation • When an unprogrammed channel is displayed, the sequential channel number and “UNPROGRAMD” are alternately displayed. • If an invalid channel number is entered using the 0-9 keys, or the Channel Select option switch is pressed with “UNPROGRAMD” displayed, an error tones sounds, “INVALID” is briefly displayed, and the displayed channel does not change. 3.5 Setting Squelch Control This radio does not have a squelch control.
General Operation Conventional channels can be either standard (analog) or Project 25 (digital). With digital operation, the DSP (Digital Signal Processor) converts the audio signal to digital data. Another difference is that analog channels use Call Guard (CTCSS/DCS) squelch control and Project 25 channels use a NAC (Network Access Code) and talk group ID codes.
General Operation Operating features unique to SMARTNET/SmartZone channels are described in Section 6. 3.7.3 P25 Trunked Mode The P25 Trunked operating features are very similar to the SmartZone type just described. Since SmartZone features are also similar to SMARTNET features, all three modes are described in Section 6. Some differences between the P25 Trunking and SmartZone modes are as follows: • Digital signaling is always used with P25 calls.
General Operation The maximum number of channels assignable to a system is limited to 864, depending on the option enabled. Channels may also be limited by available memory space as described in the following information. 3.7.4.2 Channels A channel selects a radio (RF) channel or talk group as follows: Conventional Analog Mode - A channel selects a specific radio channel, Call Guard (CTCSS/DCS) squelch coding, and other parameters unique to that channel.
General Operation The radio cycles through several informational displays, which are described in Table 3.1. Table 3.1 Initial Messages 5300 ES Description SERVICE Test Tune Mode initial message FIRMWARE Firmware display message V X.Y.Z Firmware version number DSP DSP display message V X.Y.Z DSP version number SEM SEM display message V X.Y SEM version number FILE FORM. File format display message V X.Y File format version number BOOTLOAD Bootload display message V X.
General Operation Refer to Table 2 for the test channels. Table 3.2 RF Test Mode Frequencies (MHz) Test Channel VHF Rx VHF Tx UHF Rx UHF Tx 700/800 MHz Rx 700/800 MHz Tx 136.075 136.025 380.075 380.025 764.0625 764.0125 142.075 142.125 390.075 390.025 769.0625 769.0125 154.275 154.225 400.075 400.025 775.9375 775.9875 160.175 160.125 411.075 411.025 851.0625 794.0125 168.125 168.075 424.975 424.925 860.0625 809.0125 173.925 173.975 425.075 425.025 869.9375 823.
General Operation 3.8.2 Control Top and Keypad Test Mode Once Control Top and Keypad Test Mode is selected from the menu, all icons are displayed and the LED lights red. Upon release of the emergency button, the radio is in Control Top and Keypad Mode. In this mode, all of the buttons and knobs on the radio can be tested to determine if they are operating correctly. Performing any event emits a tone and an appropriate display.
S E C T I O N 4 Radio Wide Features Section4 This section describes Radio Wide features including: • Option Switches • Time-Out Timer • Home Zone-Channel Select • Power Output Select • Alert Tone Select • Power Turn-Off Delay • Horn Alert • Microphone Off-Hook Detect • Surveillance Mode • Public Address • Scanning • Scan Lists 4.
Radio Wide Features Table 4.
Radio Wide Features Table 4.1 Programmable Option Switch and Menu Mode Functions Programmable Functions 4.
Radio Wide Features 4.3 Time-Out Timer The time-out timer disables the transmitter if it is keyed for longer than the programmed time. It can be programmed on each channel for times of 15 seconds to 3 minutes, 45 seconds or it can be disabled. If the transmitter is keyed continuously for longer than the programmed time, the transmitter is disabled, a continuous tone sounds, and “TX TIMEOUT” is displayed. Five seconds before time-out occurs, a warning beep sounds to indicate that time-out is approaching.
Radio Wide Features Pressing the TX PWR switch toggles the power setting. The new level is flashed in the display when this switch is pressed as “HI POWER” or “LOW POWER”. If selectable power is not permitted on the current channel or system, the fixed power level is flashed and no power change occurs. The selected power level is permanent until it is manually changed again. The power levels are set at the factory or when the radio is tuned using the PCTune™ software. 4.
Radio Wide Features 4.8 Horn Alert The horn alert feature sounds an external alert such as the vehicle horn when certain calls are received. It is available if a Horn option switch is programmed and the proper connection has been made to the external alert. The horn alert output is pin 4 of the accessory cable, and an external driver circuit of some type is usually required. Refer to the Installation section of the 5300 ES Service Manual for more information on how to install this feature.
Radio Wide Features 4.10 Surveillance Mode If the Surveillance mode is programmed, the backlight, all alert tones, and front panel LED indicator can be disabled individually or totally, based on programming. The transmit/receive LED indicator, display and keypad backlight, and all alert tones can be disabled. When setting is enabled, the radio will power up in Surveillance mode with the selected options active.
Radio Wide Features There are two scan modes available: Priority (standard) and Radio Wide. The operation of the priority type is unique to the system type programmed on the selected channel, and the operation of the Radio Wide type is the same regardless of the system type programmed on the selected channel. Only one type of scanning can be enabled at a time. For example, if priority scanning is enabled and Radio Wide Scan is enabled, priority scanning is automatically disabled and vice versa.
Radio Wide Features Note Use radio wide scanning only if two different types of channels need to be scanned at the same time such as conventional and SMARTNET/SmartZone. Otherwise, use the more efficient priority scanning because there is less chance of missed calls. • To turn radio wide scanning on, press the RWS option switch and “RW SCN ON” is briefly displayed. In addition, is displayed along with an R in the left Status position.
Radio Wide Features 4.12.5 Nuisance Channel Delete With priority scanning, channels can be temporarily deleted from the scan list, for example, if messages become annoying. This feature is not available with radio wide scanning. Channels can also be permanently added or deleted from a scan list as described in the next sections. Proceed as follows to temporarily delete a channel: Note The selected channel and also conventional priority channels cannot be deleted from the scan list.
Radio Wide Features 4.13.1.1 Determining Channels in Priority Scan List Channels in the conventional priority scan lists are determined as follows. Channels in the SMARTNET/SmartZone/P25 Trunked priority scan lists are indicated only when editing a list (see “Editing a Priority Scan List”). 1 Enable Priority scanning as described in Section 4.12.1. Also select the scan list if applicable as described in the following “Selecting a Priority Scan List” description.
Radio Wide Features 4 Select the channel you want to add or delete by rotating the Select switch. After the last channel in the current zone is displayed, the first valid channel in the next zone is displayed and vice versa. Lists are limited to 256 channels. If an attempt is made to add more than 256, “LIST FULL” is displayed and a channel must be deleted before another can be added. Note Priority channels can be deleted.
Radio Wide Features 4.13.2.2 Editing a Radio Wide Scan List If the RWS ED option switch is programmed, the radio wide scan list can be edited. Changes are permanent (cycling power does not reselect a default condition). Proceed as follows: 1 Make sure that both priority and radio wide scanning are OFF (the rotating icon is not indicated in the right status display). Select the scan edit mode by pressing the RWS ED option switch.
Radio Wide Features 4-14 5300 ES Series Mobile Radio Operating Manual March 2008
S E C T I O N 5 Conventional Features Section5 An overview of the conventional operating mode is located in Section 3.7.1. The following information describes the features unique to analog and Project 25 (digital) conventional operation. Refer to the preceding “Radio Wide Features” section (Section 4) for information on features common to all operating modes. 5.
Conventional Features Busy Indicator - With scanning disabled, note if the multi-function indicator on the front panel is steady green. If it is green, a carrier is being detected, so the channel may be busy. If it is not, the channel is not being used and a call can be transmitted. Monitor Mode - There may be times when the busy indication is displayed even though no one is using the channel. Monitoring should then be performed by disabling Call Guard squelch (or group ID detect on P25 channels).
Conventional Features 5.3 Busy Channel Lockout The Busy Channel Lockout (also called Transmit Disable on Busy) feature automatically disables the transmitter if the channel is busy when the PTT switch is pressed. When the transmitter is disabled by this feature, “BUSY” is displayed, a busy tone sounds, and the transmitter is disabled. The Busy Channel Lockout feature can be programmed to operate as follows. Each conventional channel can be programmed differently.
Conventional Features 5.4.1 Call Guard Squelch Enable / Disable The SEL SQ option switch (if programmed) can be used to disable receive Call Guard squelch (Normal/Selective Squelch) on analog channels or group ID code detection on P25 channels. When selective squelch is disabled, “SQ NORMAL” is flashed in the display, and when it is enabled, “SQ SELECT” is flashed. When “SQ NORMAL” is selected, the receiver unsquelches only if a carrier is detected.
Conventional Features 5.4.4 Selective Squelch Code Select (CTCSS / DSC / NAC) This feature allows the normal transmit and receive Call Guard (CTCSS/DCS/NAC) programming to be temporarily overridden with a code selected from a preprogrammed list. It is available if the SQ LIST option switch and a CTCSS/NAC code list have been programmed. In addition, with the Handheld Control Unit (HHC) only, conventional systems can be programmed for the Keypad CTCSS/DSC feature.
Conventional Features 5.5 Penalty Timer A penalty timer may be programmed on conventional systems to prevent transmissions for the programmed time after the time-out timer disables the transmitter (see Section 4.3). The penalty timer can be programmed for the same times as the time-out timer, and timing starts when the PTT switch is released. If the PTT switch is pressed while the timer is running the timer stops, and continues when the PTT switch is released.
Conventional Features Repeater talk-around can be selected if the RTA option switch is programmed. When talkaround is enabled by this switch, “RTA ON” is flashed in the display, and when it is disabled, “RTA OFF” is flashed. This feature remains enabled during scanning, and changing channels or turning power OFF does not change the selected condition. Talkaround is available on conventional channels only.
Conventional Features Proceed as follows to send an emergency alarm: 1 If required, select a channel of a system on which Emergency Alarms are enabled and then press the EMER option switch. The radio then automatically transmits the emergency alarm. 2 Either Normal or Silent operation can be programmed. With the Normal mode, the red LED lights, the emergency tone sounds, and “EMERGNCY” flashes in the display. This indication continues to flash until the alarm mode is ended (see Step 4).
Conventional Features If the emergency call is sent on a P25 channel, an emergency indication is sent according to the P25 standard (the emergency bit is set in the Common Air Interface). If it is sent on an analog channel, the DTMF Emergency ID is sent in place of the ANI DTMF PTT ID if applicable. Note The DTMF Emergency ID is sent only if pre- or post- DTMF ANI is enabled on the channel by programming. 5.9.3.
Conventional Features 5.10 Conventional Mode Scanning Channel scanning features common to all operating modes are described in Sections 4.12 and 4.13. The following information describes features unique to conventional operation. 5.10.1 Selecting a Scan List Conventional systems are programmed with a default scan list that is normally selected by all channels in that system. However, there is a programmable option to slave a particular conventional scan list to a zone.
Conventional Features Priority/Tx Priority (1) - Priority sampling occurs and the priority channel or channels are those programmed in the selected scan list. The radio transmits on the priority (1) channel. Priority (1) on Selected - The priority (1) channel is always the selected channel. The radio transmits on the selected channel. Talkback - No priority sampling occurs. The radio transmits on the channel of a call while scanning is halted or during scan hold time.
Conventional Features The priority channel sampling frequency is determined by the programmed Priority Lookback Time A (see description which follows). For example, if 2.0 seconds is programmed, the priority channel is sampled every 2.0 seconds when listening to a message on a non-priority channel. When not listening to a message, the priority channels are scanned in the normal scan sequence. With dual priority, the first and second priority channels are alternately sampled at the Loopback Time.
Conventional Features 5.11 Standard Conventional Calls Standard conventional calls can be placed to other radios monitoring the selected channel. The proper coded Call Guard squelch tone or code or P25 NAC may need to be transmitted by your radio for them to receive your call (see Sections 5.4 and 5.13.3). 5.11.1 Placing a Standard Conventional Call To place a standard conventional call, proceed as follows: 1 Turn power ON and set the volume as described in Section 3.1.
Conventional Features Pre-Tx ANI - A preprogrammed ANI sequence is automatically sent each time the PTT switch is pressed. Post-Tx ANI - A preprogrammed ANI sequence is automatically sent each time the PTT switch is released. When an emergency alarm or call is placed, this ANI signaling is replaced by the Emergency DTMF ID (see Section 5.9). Refer to Section 5.12.3 for information on MDC1200 ANI. 5.12.1 Single Tone Encoder The radio will transmit and send a single tone as programmed in PC Configure.
Conventional Features 5.13 Project 25 Mode Features The following features are unique to conventional P25 channels. 5.13.1 Digital Unit ID Each radio that operates on Project 25 (digital) channels is programmed with an up-toeight-digit unit ID. This ID is unique for each radio and can be any number from 116,777,215. When power is turned on with a Project 25 channel selected, this ID is briefly displayed. 5.13.
Conventional Features User Group ID - If the group ID of the call being received is included in a preprogrammed User Group ID list, the alias programmed in that list for that group is displayed. 5.13.4.1 Changing Talk Group Assigned To a Channel If the TG SEL option switch is programmed, the talk group assigned to a channel can be changed by the user.
Conventional Features 4 When a unit ID call is received, two beeps sound (if tones are enabled), and “CALL RCVD” and the alias of the Unit ID are alternately flashed. 5 To respond, select the Unit Call mode by pressing the Unit Call option key. - If the call timer times out (set by programming) or the channel is changed before a response is made, the unit call mode is exited. 5.13.6 P25 Conventional Telephone Calls Telephone calls can be placed and received on P25 conventional channels.
Conventional Features 2 Momentarily press the PHONE option switch and the display indicates the last number dialed by alternately displaying “LAST NUM” and the telephone number. In addition, the phone mode is indicated by the icon. 3 If required, rotate the Select switch to display the desired number. The alias and telephone number are alternately displayed. 4 Briefly press the PTT switch to send the access code. A dial tone sound should then be heard. Briefly press the PTT switch again to send the digits.
Conventional Features 5.13.7 Call Alert The Call Alert™ feature allows pages to be sent and received on P25 conventional channels. The Call Alert Encode and Decode options must be enabled to send or receive an alert. Operation is similar to SMARTNET/SmartZone and P25 Trunked channels. To answer a page: 1 When a page is received, five beeps sound and “PAGE RCVD” is displayed. The ID of the radio paging you is stored as the last ID received. 2 To clear or ignore the page, press any option switch.
Conventional Features 5.13.8 Messaging The messaging feature allows preprogrammed messages to be sent to a dispatcher on P25 channels. Up to 16 messages can be preprogrammed, and they are identified by an alias. If a MSG (Message) option switch is programmed, messages are sent as follows: 1 Momentarily press the MSG option switch. The alias of the last message sent is displayed. 2 If required, rotate the Select switch to display the desired message.
Conventional Features 5.13.10 P25 Packet Data P25 packet data transmission capability is available with 5300 ES mobile radios. A Data option switch must be programmed to toggle the data mode ON and OFF. The P25 Packet Data mode allows a subscriber unit to act as a packet data modem for a remote application connected to the subscriber unit through an RS-232 or Serial Line Internet Protocol (SLIP) connection. The SLIP connection requires an Ethernet port. A special Data Pigtail Cable, Part No.
Conventional Features 5.14.1 Menu Structure A menu system is used to select parameters in the keypad programming mode. To enter the Menu Mode, press and hold the Select button until it beeps and enters the Menu Mode. Rotate and press the Select switch to scroll through and select the available parameters. The available parameters and the section in which each is described are as follows: • CHNG ZONE (5.14.3) • CHNG CHAN (5.14.4) • SYS PARMS (5.14.5) • CHAN PARMS (5.14.
Conventional Features When an attempt is made to select a system or channel parameter in a password protected zone, “PASSWORD” is flashed. The password is always eight digits long and is entered using the same procedure as used for the power-up password described in Section 3.2. After the password is entered, system and channel parameters for that zone can be reprogrammed normally. 5.14.
Conventional Features TX TIMER - Selects the transmit time-out timer. Rotate the Select switch to decrement/increment the timer in 15-second steps from 0-225 or disable it by selecting 0 seconds. When the desired value is displayed, store it by pressing the Select switch. PEN TIMER - Selects the penalty timer. Rotate the Select switch to decrement/ increment the timer in 15-second steps from 0-225 or disable it by selecting 0 seconds.
Conventional Features RX NAC - Selects the receive Network Access Code (NAC) which can be any number from 1-4095. This number is displayed in hexadecimal from 000-FFF. Rotate and press the Select switch to enter the desired code. The displayed code is stored after the last digit is programmed. If an invalid code is entered, a beep sounds, “INVALID” is briefly displayed, and the NAC editing mode continues to be selected. TX NAC - Selects the transmit NAC the same as RX NAC above.
Conventional Features TG ID (P25 Only) - Selects the talk group for the selected channel. Rotate the Select switch to display the alias of each preprogrammed talk group and then press it to store the desired talk group. Transmit Type (P25 Mixed Mode Only) - If the selected channel is a mixed mode, analog and P25 channel, this selects the transmit type. Either Analog or Digital (P25) can be selected. This then determines if a Tx Code or Tx NAC is programmed above.
S E C T I O N 6 SMARTNET / SmartZone / P25 Trunked Features Section6 An overview of the SMARTNET/SmartZone and P25 trunked operating modes is located in Section 3.7. The following information describes the features unique to these modes of operation. Refer to the “Radio Wide Features” section, Section 4, for information on features common to all operating modes. 6.1 Analog and Digital Operation Either analog or digital operation can be selected for communication on SMARTNET traffic channels.
SMARTNET / SmartZone / P25 Trunked Features 6.2.1 Radio Info button If programmed, the Radio Info button, when pressed, allows the user to display the ID programmed for the currently selected protocol. If the radio is on a digital conventional channel and the info button is pressed, it shows the digital conventional ID. If the radio is currently on a SmartNet/SmartZone or P25 Trunking channel location, it shows the ID associated with that protocol.
SMARTNET / SmartZone / P25 Trunked Features - If a continuous tone sounds and “OUT OF RANGE” is displayed, you may be out of range of the site or blocked from it by radio-shielding structures or objects. Drive away from shielding structures or objects and try again. If this does not work, drive closer to the site. - If your unit ID is invalid, the call is being made to an invalid group ID, or group calls are not enabled, “DISABLED ID” is displayed and an alert tone sounds.
SMARTNET / SmartZone / P25 Trunked Features 6.4 Private (Unit-To-Unit) Calls Private calls allow calls to be placed to a specific radio unit. Either the Enhanced Private Conversation™ or standard Private Conversation modes may be programmed depending on the capabilities of the radio system. One difference between these call types is that the Enhanced type provides an indication that the called mobile is not on the air and the standard version does not.
SMARTNET / SmartZone / P25 Trunked Features With the Hand-Held Control Unit (HHC), enter the number using the DTMF keypad. To cancel the call, press the Private Call Option key again. 3 Press the PTT switch to initiate the call. If the entered number is valid, the display indicates the alias of the ID if it matches an ID in the call list. Otherwise, the ID you entered continues to be displayed.
SMARTNET / SmartZone / P25 Trunked Features To make a direct entry using front controls or keypad on the HHC: 1 Press and hold the Private Call option key until a tone sounds (approximately one second). The last ID called is displayed. 2 If using the front panel controls, enter the ID of the radio you are calling (five digits for Private Call, eight digits for Unit Call) by rotating and pressing the Select switch. With the HHC, enter the number using the DTMF keypad.
SMARTNET / SmartZone / P25 Trunked Features - If the system is busy when a response is made, “BUSY” is displayed and the busy tone sounds. 6.5 Telephone Calls The telephone call feature allows telephone calls to be placed and received over the public telephone system using your radio. The type of call (secure/clear) is determined by the mode selected by the Clear/Secure option switch. Telephone calling is programmed to operate in one of the following modes: • Disabled (telephone calls not available).
SMARTNET / SmartZone / P25 Trunked Features always displayed. With the HHC, enter the number using the DTMF keypad (a pause indicated by “P” is entered by * #). 3 Press and hold the PTT switch and dial the number using the keypad on the HHC. “DIALING” is displayed. Events that may occur are as follows: - If the access is successful, a dial tone sounds and the dialed number is displayed and sent. Either ringing or a busy signal is then heard as with a standard telephone call.
SMARTNET / SmartZone / P25 Trunked Features 6.6 Call Alert The Call Alert™ feature allows pages to be sent and received. With SMARTNET/ SmartZone operation, either the Enhanced Private Conversation™ or Standard Private Conversation mode may be programmed depending on the capabilities of the radio system. With P25 Trunked operation, operation is similar to the enhanced mode. 6.6.1 Answering a Page To Answer a Page: 1 When a page is received, five beeps sound and “PAGE RCVD” is displayed.
SMARTNET / SmartZone / P25 Trunked Features 2 If required, rotate the Select switch to display the desired mobile. The tag of each number is displayed. 3 Press the PTT switch and one of the following then occur: - If five beeps sound, the system received the page and the paged mobile is on the air and received it. The page mode is automatically exited.
SMARTNET / SmartZone / P25 Trunked Features 1 Momentarily press the Status option switch. The alias of the current status condition is displayed. 2 To change the current status, rotate the Select switch until the desired status is displayed. Then press the Select switch to accept that status. One of the following conditions then occurs: - If five beeps sound and “ACK RCVD” is displayed, the status was received and acknowledged by the system.
SMARTNET / SmartZone / P25 Trunked Features Proceed as follows to send an emergency alarm: 1 Press the Emergency option switch. The radio automatically transmits the emergency alarm if programmed. 2 When the emergency alarm is acknowledged, “ACK RCVD” is briefly displayed and the emergency acknowledge tone (five beeps) sounds. Silent operation may also be programmed in which case no tone sounds and there is no indication that an acknowledgment occurred.
SMARTNET / SmartZone / P25 Trunked Features 6.9.3.1 Emergency Hot Mic If Emergency Hot Mic has been enabled for emergency calls, automatic transmitting occurs with microphone audio unmuted without having to manually press the PTT switch. The automatic transmit period is programmed for 10-120 seconds in ten-second intervals. If the “Increment by 1” option is enabled, the automatic transmit period is programmed for 1-12 seconds in one-second intervals.
SMARTNET / SmartZone / P25 Trunked Features 5 To exit this mode, cycle radio power or press and hold the Emergency switch. 6.10 Failsoft Operation If a failure occurs in the SMARTNET/SmartZone or P25 Trunked system so that it cannot be used, the system directs the radio to automatically enter the failsoft mode. When in this mode, “Failsoft” and the alias of the selected channel are alternately displayed. A failsoft tone may also be heard, depending on how the repeater is programmed.
SMARTNET / SmartZone / P25 Trunked Features • The selected scan list can be temporarily changed if the Scan (List) Select option switch is programmed. The procedure is described in Section 6.11.2. • In addition to calls on channels in the scan list, pages, private/unit calls, and telephone calls are received while scanning. Private and telephone calls are not interrupted by priority messages. • P25 Trunking allows two Priority talk groups per list.
SMARTNET / SmartZone / P25 Trunked Features Note The Priority Monitor must not be confused with Transmit Priority, which is used when a call is placed in Queue when all the Voice Channels are busy. 6.11.2 Scan List Editing and Selection SMARTNET/SmartZone and P25 Trunked scan lists are user programmable if the SCN ED option switch is programmed. The procedure is described in Section 4.13.1.
SMARTNET / SmartZone / P25 Trunked Features Otherwise, if the lock mode was not specified, the selected talk group can be manually changed and the previous talk group is reselected if power is cycled. If a locked regroup command is received, the displayed talk group cannot be changed manually or by cycling power. It can be changed only after a clear order is received from the console.
SMARTNET / SmartZone / P25 Trunked Features Note Remember that not all members of the talk group are receiving your message. Missing members will start receiving your message as channels become available. 6.13.2 Site Trunking Site trunking occurs when a site can no longer participate in wide area trunking. It is disconnected from other sides and only supports calls with other radios on that site and cannot route audio to other sites.
SMARTNET / SmartZone / P25 Trunked Features 6.13.5 Auto Site Search Auto site search automatically searches and selects the best site available. User selection of sites is not available in Auto Site mode. 6.13.6 ZoneFail Site Lock This is an optional feature that can be enabled only by factory programmed. It does not require any special inputs from the infrastructure to operate. This feature is intended to prevent some of the confusion resulting from a site controller failure.
SMARTNET / SmartZone / P25 Trunked Features the radio searches the list of control channels programmed into the radio. Full Spectrum CC Scan - If the two preceding methods do not locate a control channel, every channel available to the radio is searched. 6.13.9 Talkgroup Steering through System Access Permissions To use system channel resources more efficiently, some system operators are using system access permissions to steer certain talkgroups to particular sites.
SMARTNET / SmartZone / P25 Trunked Features b The dynamic site list is checked to see if any newer receive/transmit channel information is available for the last site ID. c The best receive/transmit information is used and the radio checks to see if this control channel is available. The result of the preceding operation is that the radio has a reasonable chance of finding a valid site, usually on the first try.
SMARTNET / SmartZone / P25 Trunked Features 6-22 5300 ES Series Mobile Radio Operating Manual March 2008
S E C T I O N 7 Miscellaneous Section7 7.1 Supervisory Tones Supervisory Tones are described as follows: Single Beep (Alert Tone) • Power was turned ON and a successful power-up sequence occurred (see Section 3.1). • The time-out timer is about to expire or the penalty timer has expired (Section 4.3). • The conversation timer is about to expire (Section 5.6). • The system received your page but the paged radio is not on the air (Section 6.6). • Telephone interconnect is not operational (Section 6.5).
• Dynamic regrouping has been exited but the dynamic regrouping channel is still selected (Section 6.12). Single Short Medium-Pitch Tone • A valid key has been pressed. Single Short Low-Pitch Tone • An invalid key has been pressed. Medium Tone (No Acknowledge) • The paged radio did not acknowledge the page (Section 6.6). • The message that was sent has not been acknowledged (Section 6.7). • The status condition that was sent has not been acknowledged (Section 6.8).
Alternating Tone • Dynamic regrouping has occurred (Section 6.12). • Dynamic regrouping has occurred but the regrouping channel is not selected (Section 6.12). Busy Signal • The radio system is busy or a busy condition exists when making a telephone call. Three Medium Pitch Tones • A channel is available after a busy condition occurred (SMARTNET/SmartZone only). 7.2 Error Messages The following are definitions of the various error messages that may be displayed.
Bad Hrdwar - The software was loaded on the wrong platform. The boot loader version does not match the expected boot loader version. I.e., the frequency band from the ESN may not match the RF deck frequency band. Batt Low - The battery voltage has been detected as being low. Busy - A call has been attempted and the system has responded that no channels are available for assignment.
Invalid - The received input from the user does not fit the criteria necessary for the feature. Invalid ID - The received ID from the user was not a valid ID. Invald Key - The key pressed by the user was not valid for the current situation. Invld Ch - The channel entered by the user in keypad programming is not valid. Key Fail - The encryption key required by the current selected group/channel is not valid. Kypd Lockd - The keypad lock function is active and key presses are not accepted in this mode.
Parms Fail - The checksum of the profile / user parameters does not match the calculated checksum. This indicates that there is an error in the parameters file. This message only occurs if the redundant copy of the parameters is also corrupt or is unable to be used. Rekey Fail - This error indicates a failure in a rekeying process. Rx Only - The selected channel is Rx only. Sts Failed - No acknowledgement was received while sending a status report.
Note If excessive background noise consistently interferes with communications, Mic Sensitivity should be adjusted (using PC Configure). Make sure that the PTT (push-to-talk) switch is pressed before you begin to speak and released as soon as the message is complete. 7.5 Operation At Extended Range When approaching the limits of radio range, the other party may not be able to hear your transmissions and there may be an increase in background noise when messages are received.
To clean the Control Head: 1 Use the brush to remove the bulk of sand and dust from the Control Head. ! CAUTION Ensure that this is done in an environment that does not allow other equipment to be affected by the removed sand and dust. If necessary, use the vacuum to collect material as it is removed. 2 When the bulk of sand and dust is removed, use the brush to clean the interface joint between the buttons and Control Head plastic.
Note March 2008 There are no user-serviceable components in the radio. Altering internal adjustments can cause illegal emissions, void the warranty, and result in improper operation that can seriously damage the radio.
7-10 5300 ES Series Mobile Radio Operating Manual March 2008
S E C T I O N 8 Determining Available Options Section8 This manual describes the operation of all features that are currently available for the 5300 ES radio. However, many of these features are optional and therefore may not be available in your radio. For example, Project 25 trunked operation is optional and may not be available. Availability of optional features is controlled by factory programming of the control logic.
Determining Available Options OTAR Options • OTAR P25 conventional • OTAR P25 trunked Trunking Options • SMARTNET analog operation • SmartZone analog operation • Digital SMARTNET/SmartZone • Multi-Net operation Feature Options • Keypad programming (Federal Government users only) • Full Keypad support • 512 or 864 talk groups depending on option enabled • Custom icons • Zonefail site lock • MDC1200 • 700 MHz Band • Conventional Vote Scan Currently, the only operating mode that is standard with all models
S E C T I O N 9 Password Description Section9 A password feature is available for 5300 ES mobile radios. The following passwords may be set: • Four Power-On (User x) Passwords • Download and Upload Passwords • Master Password Software Versions Required: PC Configure 2.4.1 or later is compatible with 5300 ES Mobile radios Version 6.x.x or later Models 9.1 Programming Passwords Passwords are programmed using PC Configure.
Password Description 9.1.1 Lost Passwords If a password is lost, contact customer service. 9.1.2 Changing Passwords An assigned password can be changed by the user if the PW CHG option switch is programmed. Selecting this function displays prompts for entering and confirming a new password. Note With the 5300 ES Handheld Control Unit, it is recommended that a number key not be used for this function because the password mode is exited if that key is pressed to enter a number. 9.1.
Password Description 9.2.3 Master Password The Master Password overrides all the preceding passwords. It can be used by a system administrator as a “pass key” to a password controlled function or to change a lost or inadvertently changed password. Master passwords are set up and changed the same as the other passwords. It does not override the following Zone Password. 9.3 Zone Password A zone password can be programmed with the 5300 ES mobile radio.
Password Description 9-4 5300 ES Series Mobile Radio Operating Manual March 2008
S E C T I O N 10 Secure Communication (Encryption) Section10 This radio may be equipped to provide secure communication on some or all channels. This feature encrypts the voice so that it can be understood only by someone using a radio equipped with a similar encryption device and encryption codes. If equipped with the Clear/Secure option switch and the current channel is programmed to allow switch selection, secure communication can be manually enabled and disabled by that switch.
Secure Communication (Encryption) 10.1.2 AES (Advanced Encryption Standard) An encryption standard called AES is replacing DES-OFB encryption on digital (P25) channels. It uses a 128-, 192-, or 256-bit encryption key instead of the 64-bit key used with DES. EFJohnson radios currently support only 256-bit AES keys. The type of encryption (DES or AES) is determined by the type of encryption key that is loaded (see Section 10.2), and not by the PC Configure programming software.
Secure Communication (Encryption) If an attempt is made to transmit a secure message without loading the corresponding key, “KEYFAIL” is displayed. The message must then be transmitted in the clear mode (this is possible only if the channel is strapped to “switchable”) or the key must be loaded. 10.2.1 Key and Algorithm IDs Each encryption key is programmed with a Key ID (also called Logical ID). This ID plus the algorithm ID (ALGID) is transmitted in the message on digital channels.
Secure Communication (Encryption) and can also be used with the with the Motorola KVL-3000 Plus. With this mode, keys are loaded into a SLN (Storage Location Number), typically from 0-4095. The Keys Table must then be programmed to link channel PIDs to a specific SLN. The use of this type of indirect linking allows keysets and key IDs to be changed through OTAR while keeping the mapping from the channel or talk group the same. For example, as shown in Figure 10.
Secure Communication (Encryption) 10.2.5 Encryption Key Erase A KY CLR option switch can be programmed that allows the user to permanently erase all stored keys. If OTAR TEK and KEK keys are stored, all keys of both types are erased. This function can be used to ensure that unauthorized encrypted calls can no longer be placed or received by a radio. On a mobile radio, you must press the erase keys button twice within a small period of time for the keys to be erased. 10.2.
Secure Communication (Encryption) If the channel has been strapped “Clear” and the option switch selects the “Secure” mode on power up and a transmission is attempted, “CLEAR ONLY” is displayed and transmitting is disabled. Likewise, if the channel is strapped “Secure” and the option switch selects the “Clear” mode on power up and a transmission is attempted, “SECURE ONLY” is displayed and the transmitter is disabled. The radio can be programmed to ignore the “Clear” or “Secure” switch setting.
Secure Communication (Encryption) 10.3.3 Talk Group Encryption Override On conventional digital (P25) channels, the encryption strapping mode and PID are programmed on a per talk group basis similar to the trunked modes (SMARTNET/ SmartZone/P25 Trunked). However, with this mode only, there is the option to override the talk group encryption programming and program it on a per-channel basis. Therefore, if desired on conventional digital channels, encryption can be programmed differently for each channel.
Secure Communication (Encryption) may be unique to a particular radio (UKEK) or common to a group of radios (CKEK). The SMA or KVL-3000 create only UKEKs, therefore you create and load UKEKs before using OTAR. 10.4.2 Keysets To simplify key management, OTAR divides the TEK keyspace into multiple sets. Exactly one of these sets is said to be active at any given time, and only keys in the currently active set will be selected for use when encrypting voice traffic.
Secure Communication (Encryption) 10.4.3 Key Management Facility The Key Management Facility (KMF) provides key management and OTAR functions to applicable radios within the radio system. One of the main tasks of the KMF is to maintain a data base of encryption information contained in each radio.
Secure Communication (Encryption) When determining this number, consider the likelihood of someone trying to spoof the system by retransmitting recorded messages and then adjust the MNP accordingly. The higher the risk, the smaller the MNP should be. A disadvantage of setting a low MNP is that the chance of rejecting valid messages becomes higher. In addition, traffic level and terrain contribute to lost messages and should also be considered when selecting this number.
Secure Communication (Encryption) Key Encryption Key (KEK) - A key used to encrypt keys contained in Key Management Messages (KMMs) during OTAR. These messages may themselves be encrypted by a TEK. These keys can be the AES or DES type. There are KEKs unique to a subscriber unit (UKEK) and common to a group (CKEK). The other type of key is the Traffic Encryption Key (TEK) used to encrypt voice and data messages.
Secure Communication (Encryption) Rekey - The process of preparing, sending, and loading encryption keys into a subscriber unit for current or future use. This may be done over-the-air (OTAR) or by directly connecting a keyloader to the subscriber unit. Radio Set Identifier (RSI) - Subscriber units are programmed with one or two Radio Set Identifier (RSI) numbers that identify the unit for OTAR purposes. The RSI can be unique to an individual subscriber unit or unique to a group of subscriber units.
Secure Communication (Encryption) Program Channel/Group PIDs and Encryption Type - With conventional analog calls, this information is programmed on the channel screen. With other types, it is programmed in the talk group list selected on the system screen. In addition, with conventional digital calls, the group programming can be overridden on the channel screen (see Section 10.3.3). Additional PIDs for special calls can also be specified on the system screen for digital and trunked calls.
Secure Communication (Encryption) KMF RSI - This RSI is normally 9,999,999 and should not need to be loaded since it defaults to this number. Verify that the above information was properly stored in the radio by viewing it using the keyloader. 10.6 Radio OTAR Capabilities The OTAR capabilities of the SEM-equipped 5300 ES mobile radio are as follows. Keysets • Up to three keysets are used and it is assumed all three are always present. Keyset IDs 1 and 2 are for TEKs and only one is active at a time.
Secure Communication (Encryption) MODIFY KEY 0x13 MODIFY KEYSET ATTRIBUTES 0x14 MODIFY KEYSET ATTRIBUTES RESPONSE 0x15 NEGATIVE ACK 0x16 NO SERVICE 0x17 REKEY ACK 0x1D REKEY 0x1E WARM START 0x20 ZEROIZE 0x21 ZEROIZE RESPONSE 0x22 OTAR REGISTRATION 0x25 OTAR REGISTARTION RESPONSE 0x26 UNABLE TO DECRYPT 0x27 10.6.1 OTAR Option Switches The following additional option switches can be programmed with the 5300 ES mobile radio to control OTAR functions.
Secure Communication (Encryption) No Service - A “No Service” reply was received from the KMF. No rekeying will take place. Rekey Fail - Either the rekey command failed or timed out (after approximately 30 seconds). This message could indicate that the rekey request message was not received by the KMF. However, depending on the KMF configuration and channel traffic, it is possible that the message was received and a response is still pending.
Secure Communication (Encryption) A sign that has not successfully OTAR registered is that the radio’s data context icon will be on, but the radio will periodically keep going back to the data channel (the data channel icon will periodically come ON and then OFF). The number of times the radio will attempt to OTAR register and the amount of time it will wait between events is configured in PC Configure. 10.
Secure Communication (Encryption) Note The radio will reset after a successful download in this mode, but the previous radio profile will remain in use until the radio user or PC Configure operator activates the OTAP parameter. If the OTAP procedure is not successful, the radio will reboot and return to normal operating mode with the current parameters. 10.7.2 OTAP Transfer Times Larger files tie up the radio for a long time.
S E C T I O N 11 Service Information Section11 This section describes how to obtain authorized service for the 5300 ES Series mobile radio. 11.1 Product Warranty The warranty statement for this equipment is available from your product supplier or from: Warranty Department EFJohnson 8050 Jetstar # 175 Irving, TX 75063 This information may also be requested from the Warranty Department by phone at the numbers listed in Section 11.4.
Service Information To register EFJohnson products online, visit www.EFJohnson.com. Click the link that says Register your EFJohnson products online or go to http://www.efjohnson.com/ WarrantyRegistration.asp. Then, follow the instructions to register your products. 11.3 Telephone Technical Support Technical support personnel can help resolve many issues over the telephone, such as display, volume, software, programming. Please refer to Section 11.
Service Information Customer Service Department EFJohnson 8050 Jetstar # 175 Irving, TX 75063 11.5 Returns for Repairs Before returning equipment for repair, contact the EFJohnson Customer Service Department as described in the preceding section. They may be able to suggest a solution to the problem, making return of the equipment unnecessary. Repair service is normally available through local authorized EFJohnson land mobile radio service centers.
Service Information 11.6 Replacement Parts Replacement parts can be ordered directly from the Service Parts Department. To order parts by phone, dial the toll-free number as described in Section 11.4. When ordering, please supply the part number and quantity of each part ordered. EFJohnson dealers also need to give their account number. If there is uncertainty about the part number, include the designator (C512, for example) and the model number of the equipment the part is from.
Index -AAES Encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2 Algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-10 Algorithm ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-10 Alias . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Alphanumeric Display . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Analog and Digital Operation . . . . . . . . . . . . . . . . . . . . . .
Index (continued) Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-10 Key Encryption Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-7 Key ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-3, 10-11 Key Loader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11 Key Management Facility . . . . . . . . . . . . . . . . . . . . . . . 10-9 Keypad Programming . . . . . . . . . . . . . . . . . . . . . . . . . .
Index (continued) Changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-2 Download/Upload . . . . . . . . . . . . . . . . . . . . . . . 9-1, 9-2 Master . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1, 9-3 Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1, 9-2 Power-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3 User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1, 9-2 Zone . . . . . . . . . . . . .
Index (continued) Unit Calls, Project 25 . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16 Unit ID, SMARTNET/SmartZone . . . . . . . . . . . . . . . . . . . 6-1 User Group ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16, 6-3 -VVolume Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 -ZZeroize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-12 Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
