Operating Manual Part 15
Table Of Contents
- Safety Information
- General
- Controls And Display
- General Operation
- Radio Wide Features
- Conventional Features
- 5.1 Monitoring Before Transmitting
- 5.2 Monitor Mode
- 5.3 Busy Channel Lockout
- 5.4 Call Guard Squelch
- 5.5 Penalty Timer
- 5.6 Conversation Timer
- 5.7 Repeater Talk-Around
- 5.8 Displaying Transmit / Receive Frequency
- 5.9 Emergency Alarm and Call
- 5.10 Conventional Mode Scanning
- 5.11 Standard Conventional Calls
- 5.12 DTMF / ANI Signaling
- 5.13 Project 25 Mode Features
- 5.14 Keypad Programming
- 5.15 Text Messaging
- 5.16 Sending Global Positioning System (GPS) Data
- SMARTNET / SmartZone / P25 Trunked Features
- 6.1 Analog and Digital Operation
- 6.2 Viewing Unit ID
- 6.3 Standard Group Calls
- 6.4 Private (Unit-To-Unit) Calls
- 6.5 Telephone Calls
- 6.6 Call Alert
- 6.7 Messaging
- 6.8 Sending Status Conditions
- 6.9 Emergency Alarm and Call
- 6.10 Failsoft Operation
- 6.11 SMARTNET / SmartZone / P25 Trunked Scanning Features
- 6.12 Dynamic Regrouping
- 6.13 SmartZone and P25 Trunking Unique Features
- 6.13.1 Busy Override
- 6.13.2 Site Trunking
- 6.13.3 Determining Current Site and Searching for a New Site
- 6.13.4 Locking / Unlocking a Site
- 6.13.5 Auto Site Search
- 6.13.6 ZoneFail Site Lock
- 6.13.7 P25 Wide Area Scan
- 6.13.8 Normal P25 and SmartZone Control Channel Hunt
- 6.13.9 Talkgroup Steering through System Access Permissions
- 6.13.10 P25 Wide Area Scan
- 6.14 P25 Trunking Unique Features
- Miscellaneous
- Determining Available Options
- Password Description
- Secure Communication (Encryption)
- Service Information
October 2008 5300 ES Series Mobile Radio Operating Manual 5-25
Conventional Features
When the desired value is displayed, store it by pressing the Select switch.A single beep
sounds when the switch is pressed (if that option is enabled).
5.14.6 Channel Parameters
The “CHAN PARMS” menu parameter selects the following conventional channel
parameters that can be reprogrammed. Press Select switch to select the “CHAN PARMS”
parameter and then rotate that switch to display the desired parameter. Then press the
Select switch again to select it. A single beep sounds when the switch is pressed (if that
option is enabled). The squelch control parameters are unique to the type of conventional
channel selected (analog or Project 25).
Note If “PASSWORD” is briefly displayed when attempting to select a parameter, see
Section 5.14.2.
Note If a mixed mode channel is selected, both the Rx Code (analog) and Rx NAC (P25) which
follow can be programmed. In addition, if the Tx Type is Analog, a Tx Code is
programmed, and if it is Digital (P25), a Tx NAC is programmed.
RX FREQ - Programs the receive channel frequency. To select the digit to change or
move the cursor to the right, press the Select switch. Then to display the desired digit,
rotate the Select switch. The frequency is stored after programming the last digit. If an
invalid frequency is entered, a beep sounds, “INVALID” is briefly displayed, and the
frequency editing mode continues to be selected.
TX FREQ - Selects the transmit frequency the same the preceding RX FREQ.
CTCSS/DCS Squelch Control (Analog Channel) - Changes the preset squelch setting
on that channel. The default setting is “0” and values of –7 to +7 can be selected.
Increasing this setting toward +7 causes the squelch to open sooner so that weaker
signals can be received, and decreasing it toward –7 causes the opposite to occur.
RX CODE - Sets the receive Call Guard (CTCSS/DCS) code. The currently selected
code is initially displayed. If required, rotate and press the Select switch to select the
desired code type (CTCSS analog or DCS digital). If an invalid code is entered, a beep
sounds, “INVALID” is briefly displayed, and the editing mode continues to be selected.
TX CODE - Selects the transmit codes the same as RX CODE above.
NAC Squelch Control (Project 25 Channel).
RX NAC - Selects the receive Network Access Code (NAC) which can be any number
from 1-4095. This number is displayed in hexadecimal from 000-FFF. Rotate and press
the Select switch to enter the desired code. A single beep sounds when the switch is
pressed (if that option is selected). The displayed code is stored after the last digit is
programmed. If an invalid code is entered, a beep sounds, “INVALID” is briefly
displayed, and the NAC editing mode continues to be selected.
TX NAC - Selects the transmit NAC the same as RX NAC above.