Installation Guide Owner's manual

TABLE OF CONTENTS
Version 4 In Ground Model 200iP/250iP Motorcycle Dynamometer Installation Guide
iii
Chapter 4 Control Panel Interface Operation
Basic CPI Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Using the Air Fuel Ratio Air Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3
Using the Emergency Stop/Dyno Shutdown . . . . . . . . . . . . . . . . . . . . . . . 4-4
Using the High Pressure Blowers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4
Understanding Interlocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Using the Power Carriage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5
Using the Starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5
Using the Status Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6
Using the Wheel Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6
Power Distribution Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8
Main Circuit Breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8
High Pressure Blower Circuit Breakers . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8
Maintenance and Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-9
Maintaining and Troubleshooting the Wheel Clamp . . . . . . . . . . . . . . . . .4-9
Replacing the Theta Controller Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-10
Troubleshooting CPI Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-11
Chapter 5 Basic Dyno Operation
Loading the Motorcycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2
Connecting the RPM Pickup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5
RPM Pickup Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5
Connecting the Primary Inductive Pickup . . . . . . . . . . . . . . . . . . . . . . . . .5-6
Connecting the Secondary Inductive Pickup . . . . . . . . . . . . . . . . . . . . . . . 5-8
Pre-run Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-10
Before Starting the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-11
Engine Warm Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-11
After Engine Warm Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-11
Making a Test Run . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-12
Preventative Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-13
Appendix A Red Head Anchor Installation
Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1
Contact Information for ITW Ramset/Red Head . . . . . . . . . . . . . . . . . . . . .A-1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-2
Appendix B Power Requirements and Installation
Locations Using 60 Hz Power (North America and Japan) . . . . . . . . . . . .B-2
Installing the Wall Receptacle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-3
Testing for Correct Voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4
Replacing the Power Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-5
Hard Wiring to the Building . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-5
Connecting the Dyno . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-6