Installation Guide User Manual

Motorcycle Dynamometer Installation Guide
LIST OF FIGURES
iv
Figure 3-6: Remove and Replace the Hood. . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Figure 3-7: Connect Your Shop Air Supply . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
Figure 3-8: Install the Rotor/Taper Lock Assembly . . . . . . . . . . . . . . . . . . . . . 3-6
Figure 3-9: Check for Run Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6
Figure 3-10: Caliper Assembly Mounting Bolts. . . . . . . . . . . . . . . . . . . . . . . .3-7
Figure 3-11: Secure the Caliper Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7
Figure 3-12: Adjust the Brake Pad Space. . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-8
Figure 3-13: Install the Air Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-8
Figure 3-14: Install the Master Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9
Figure 3-15: Install the Metal Brake Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9
Figure 3-16: Install the Spring Bolt Assembly . . . . . . . . . . . . . . . . . . . . . . . .3-10
Figure 3-17: Secure the Air Hose to the Regulator . . . . . . . . . . . . . . . . . . . .3-11
Figure 3-18: Install the Bulk Head Fitting . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12
Figure 3-19: Wire Set Up 1—Terminal Strip Wiring . . . . . . . . . . . . . . . . . . .3-13
Figure 3-20: Wire Set Up 1—Breakout Board Wiring . . . . . . . . . . . . . . . . . .3-13
Figure 3-21: Wire Set Up 2—Terminal Strip Wiring . . . . . . . . . . . . . . . . . . .3-14
Figure 3-22: Wire Set Up 2—Breakout Board Wiring and
Jumper Settings
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-14
Figure 3-23: Air Brake Assembly Schematic . . . . . . . . . . . . . . . . . . . . . . . . .3-16
Figure 3-24: Modify the Tire Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-18
Figure 3-25: Remove the Extension Arm Assembly from the Crate . . . . . . 3-19
Figure 3-26: Secure the Extension Arm Assembly to the Tire Stop . . . . . . . 3-19
Figure 3-27: Install the Fan Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-20
Figure 3-28: Install the Outlet Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-21
Figure 3-29: Modify the Extension Arm Assembly—
Removing the Arms
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-22
Figure 3-30: Modify the Extension Arm Assembly—
New Arm Configuration
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-23
Figure 3-31: Remove the Carriage Screw Support Bracket . . . . . . . . . . . . .3-25
Figure 3-32: Remove the Tire Carriage, Nut Block, and Clamps. . . . . . . . . 3-25
Figure 3-33: Remove the Top Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-26
Figure 3-34: Install the Extended Carriage Support Bracket . . . . . . . . . . . .3-26