ASSEMBLY INSTRUCTIONS DX-WD1239 TV Cart Safety information and specifications ............2 Tools needed............................................................3 Package contents ...................................................3 Assembly instructions...........................................
DX-WD1239 Safety information and specifications CAUTION: This TV cart’s work surface is intended only for use with a product not weighing more than 95 lbs. (43.09 kg) and having 42" wide flat-panel TV dimensions that will permit it to sit evenly on your TV cart. Using with other products, including products that weigh more than the maximum weight allowed, may result in instability, which may cause possible injury. Maximum weight: 95 lbs. (43.
DX-WD1239 3 Tools needed No. 2 Phillips screwdriver Hammer Caution: Do not use an electric drill or screwdriver Package contents Package contents: hardware Make sure you have all the hardware necessary to assemble your new TV cart: Label I2 Hardware Hidden cam Qty. Label 9 M J2 Cam dowel 9 K Swivel caster 2 L Hardware Metal pin N Rubber sleeve Warning label O Qty. 8 4 1 2 Non-swivel caster Using a screw that is too long will cause damage your TV cart.
DX-WD1239 Package contents: parts Note: All parts except for the stop molding (H) have a lettered sticker to make identifying parts easier. Letter Description Qty. Letter Description Qty.
DX-WD1239 5 Assembly instructions Step1: Assemble your TV cart on a carpeted floor or on the empty carton to avoid scratching your TV cart or the floor. Push nine hidden cams (I2) into the ends (A and B), upright (C), and top (D), then insert the metal end of a cam dowel (J2) into each hidden cam. Do not tighten the hidden cams in this step.
DX-WD1239 Step 2: Insert two metal pins (M) into the two holes beside the hidden cam on the right end (A). Repeat this step for the left end (B).
DX-WD1239 7 Tightening hidden cams In the remaining steps, use these illustrations for instructions on tightening hidden cams. Warning: Risk of damage or injury. Hidden cams must be completely tightened. Hidden cams that are not completely tightened will loosen, and parts may separate. Arrow Make sure that you turn the hidden cam a minimum of 190° to a maximum of 210°. Note the position of the arrow on the hidden cam. Arrow 210° In the illustration below, the hidden cam has not been tightened enough.
DX-WD1239 Step 3: Fasten the stop molding (H) to the top (D). Use a Phillips screwdriver to tighten three hidden cams. See “Tightening hidden cams” on page 7.
DX-WD1239 9 Step 4: Fasten the left end (B) to the top (D). Use a Phillips screwdriver to tighten two hidden cams. See “Tightening hidden cams” on page 7.
DX-WD1239 Step 5: Slide the valance (G) onto the two metal pins (M) in the left end (B).
DX-WD1239 11 Step 6: Fasten the right end (A) to the top (D). Use a Phillips screwdriver to tighten two hidden cams. See “Tightening hidden cams” on page 7. Note: Make sure that the metal pins in the right end (A) insert into the holes in the valance (G).
DX-WD1239 Step 7: Fasten the upright (C) to the top (D). Use a Phillips screwdriver to tighten two hidden cams. See “Tightening hidden cams” on page 7. Fasten the bottom (E) to the ends (A and B) and upright (C). Use a Phillips screwdriver and six black 1 7/8" flat head screws (P).
DX-WD1239 13 Step 8: Fasten the swivel casters (K) and the non-swivel casters (L) to the bottom (E). Use a Phillips screwdriver and 16 black 9/16" large head screws (Q) (four screws per caster). The tabs on the non-swivel casters (K) must insert into these holes.
DX-WD1239 Step 9: Carefully stand your TV cart upright. Push the rubber sleeves (N) on the metal pins (N), then insert the metal pins into the hole locations of your choice in the right end (A) and upright (C). Set the adjustable shelf (F) onto the metal pins (M). Apply the warning label (O) to the top (D). You should be able to read the label when the TV is removed from your TV cart. When the TV is in place, it should hide the label. Peel off the backing and apply the label as shown.
DX-WD1239 15 Still need help? For customer service, call: 800-305-2204 (U.S./Canada markets) Distributed by Best Buy Purchasing, LLC 7601 Penn Avenue South, Richfield, MN USA 55423-3645 © 2011 BBY Solutions, Inc. All rights reserved. DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and brand names are trademarks of their respective owners.
Certificate of Conformity 1. This certificate applies to the Sauder Woodworking Product identified by this instruction booklet. 2. This certificate applies to the compliance of this product with the CPSC Ban on Lead-Containing Paint (16 CFR 1303). 3. This product was manufactured by: Sauder Woodworking Company 502 Middle Street Archbold, Ohio 43502 (419) 446-2711 4. Date of Manufacture: ____________ Lot number: 346230 www.dynexproducts.
