Submittal Sheet

ManualsBrandsDynesic ManualsChemicals & CompoundsSILVERSHIELD Indoor/Outdoor Epoxy Paint with Silver Flake (1 Gallon Kit)

Product Data

SILVERSHIELD

5000X

SELECTION & SPECIFIC DATA

Recommended Uses

• Indoor/Outdoor Protection Epoxy Paint

• Pipe Exterior & Pipe Racks

• Support Columns

• Tank Tops and Tank Surfaces

• Rust Inhibitor and Condensation Barrier

Color/Part# Silver/5000X

Finish Gloss

Primer Self-priming

Topcoats Acrylics, Epoxies, Polyurethanes

Dry Film Thickness 4-12 mils per coat

Solids Content By Volume 100%

Theoretical Coverage Rate 267 square feet at 6 mils 133 square feet at 12 mils

Dry Temp. Resistance Continuous: 250°F (121°C) Non-Continuous: 300°F (149°C)

Container Sizes 4x1 kg unit (53sq.ft. @ 6 mils) or 1x1 gallon kit (266sq.ft. @ 6

mils.)

Recommended Thickness 6-12 mils.

Flexibility ASTM D522-4 - >35%

Flash Point Resin: >300°F (149°C) hardener: >200°F (93°C)

Pull Off Adhesion Test ASTM D4541 - 1,600 psi

Specific Gravity resin: 1.20 hardener: 1.48

Mix Ratio 3-1 Part A to Part B by volume

Weight per gallon 9.83 lbs.

Generic Type

Zinc Rich Polyamado-Amine Epoxy

Description

SILVERSHIELD is a high grade, two part epoxy with

anti corrosion resistance fillers designed for long term

protection to seal and protect rusted surfaces. SILVER

SHIELD contains silver flake that maintains a metallic

silver finish. SILVERSHIELD can be applied over manually

prepared surfaces to provide a primer or a top coat for

corroded areas where blasting is not an option. SILVER

SHIELD is easy to apply by brush, roller or sprayer to

achieve a 4 to 10 mils. dry film thickness. SILVERSHIELD

covers 266 square feet at 6 mils. For large surface areas

SILVERSHIELD can be sprayed with a 30:1 airless or

higher. You can coat over the top of SILVERSHIELD 6

hours after installation depending on the temperature.

Product Features & Benefits

• Excellent Corrosion Resistance - 1600 psi Adhesion

• Low Stress, Highly Flexible Film

• Edge and Corner Protection

• Surface Tolerant

• 100% Solids, No VOCs

• Works on Metal, Fiberglass, Stainless Steel,

Concrete and Wood Surfaces.

• Contains Silver Flake for Long Term Metallic Finish

• Rust Inhibitor - Indoor/Outdoor Epoxy Paint

Summary of content (3 pages)

PAGE 1
Product Data SILVERSHIELD 5000X SELECTION & SPECIFIC DATA Generic Type Zinc Rich Polyamado-Amine Epoxy Description SILVERSHIELD is a high grade, two part epoxy with anti corrosion resistance fillers designed for long term protection to seal and protect rusted surfaces. SILVER SHIELD contains silver flake that maintains a metallic silver finish. SILVERSHIELD can be applied over manually prepared surfaces to provide a primer or a top coat for corroded areas where blasting is not an option.
PAGE 2
Product Data SILVERSHIELD 5000X 2. SERVICE TEMPERATURE Dry Service - 250°F (121°C) Spill/Splash - 180°F (82°C) Immersion - *140°F (60°C) SUBSTRATES & SURFACE PREPARATION General Clean and dry surface removing dirt, dust, oil and other contaminants. * For Previous Painted Surfaces consult Dynesic Technologies. APPLICATION EQUIPMENT GUIDELINES Listed below are general equipment guidelines for the application of this product.
PAGE 3
Product Data SILVERSHIELD 5000X 3. CLEAN-UP & SAFETY Cleanup Safety Ventilation Use MEK or Acetone. In case of spillage, absorb and dispose of in accordance with local applicable regulations. Read and follow all caution statements on this product data sheet and on the SDS for this product. Wear protective clothing, gloves and use protective cream on face, hands and all exposed areas.