User Manual iGO primo Navigation software for the [DEVICE] UK English October 2012, ver. 1.
Thank you for choosing the [DEVICE] as your navigator. Read the Quick Start Guide first and start using [DEVICE] right away. This document is the detailed description of the navigation software. You can easily discover iGO primo while you are using it; however, we still recommend that you read this manual to fully understand the screens and features. Easy map updates It is easy to keep the navigation system up to date.
Table of contents 1 Warnings and Safety information .........................................................................6 2 Getting started .........................................................................................................7 2.1 Navigation menu ............................................................................................................ 9 2.2 Buttons and other controls on the screen ..................................................................... 10 2.2.
3.1.3.2 Searching for a Place of Interest using preset categories .......................................................... 48 3.1.3.3 Searching for a Place of Interest by category ............................................................................ 50 3.1.3.4 Searching for a Place of Interest by name ................................................................................. 52 3.1.3.5 Selecting nearby assistance from 'Where Am I?' ............................................................
6.1.2 Daytime and night colour themes ...................................................................................... 86 6.1.3 Tunnel view ....................................................................................................................... 86 6.1.4 Route calculation and recalculation ................................................................................... 87 6.1.5 Green routing ..............................................................................................
1 Warnings and Safety information The navigation system helps you find your way to your destination with the built-in GPS receiver. iGO primo does not transmit your GPS position; others cannot track you. If you accept it when first using the application, iGO primo collects usage information and GPS logs that may be used for improving the application and the quality and coverage of maps. The data is processed anonymously; no one will be able to track any personal information.
2 Getting started iGO primo is optimised for in-car or pedestrian use. There is no need to use a stylus. You can use it easily by tapping the screen buttons and the map with your fingertips. When using the navigation software for the first time, an initial setup process starts automatically. Do as follows: 1. Select the written language of the application interface. Later you can change it in Regional settings (page 112). 2. Read the End User Licence Agreement. Tap 3.
6. If needed, modify the time format and unit settings. Later you can change them in Regional settings (page 112). 7. If needed, modify the default route planning options. Later you can change them in Route settings (page 104). 8. If an Internet connection is available, the application will check your licenses for the online services. This may take a few seconds. When finished, you will be asked to activate these services. You can choose to activate them later or do it right away. 9.
2.1 Navigation menu You can reach all parts of iGO primo from the Navigation menu. You have the following options: • Tap to select your destination by entering an address or selecting a place of interest, a location on the map or one of your Favourite destinations. You can also look up your recent destinations from the Smart History, enter a coordinate or use the location saved in a photo. When internet connection is available, Google Local Search can be a further help to find your destination.
2.2 Buttons and other controls on the screen When you are using iGO primo, you usually tap buttons on the touch screen. You only need to confirm selections or changes if the application needs to restart, it needs to perform a major reconfiguration, or you are about to lose some of your data or settings. Otherwise, iGO primo saves your selections and applies the new settings without confirmation as soon as you use the controls.
When a feature can be set to different values in a range, iGO primo shows an indicator on a gauge that displays and sets the value. Slider • Drag the handle to move the slider to its new position. • Tap the slider where you want the handle to appear; the thumb jumps there. Each key is a touch Alphabetic and screen button. alphanumeric keyboards to enter text and numbers. Virtual keyboard 2.2.1 Using keyboards You only need to enter letters or numbers when you cannot avoid it.
Task Instruction Finalising the keyboard entry (opening the list of search Tap results) . Finalising the keyboard entry (saving your input) Cancelling the keyboard entry (returning to the previous screen) Tap . Tap . 2.2.2 Beyond single screen tap You usually need to tap the screen only once. However, some useful features can be accessed with combined touch screen tapping.
2.3 Map screen 2.3.1 Navigating on the map The Map screen is the most frequently used screen of iGO primo. A small live map is displayed on the Navigation menu, as a part of the button. To enlarge this small map and open the Map screen, tap . This map shows the current position (the Vehimarker, a blue arrow by default), the recommended route (an orange line), and the surrounding map area. When there is no GPS position, the Vehimarker is transparent. It shows your last known position.
The data fields are different when you are navigating an active route and when you have no specified destination (the orange line is not displayed). Default data fields when cruising without a destination (tap and hold any of the fields to change its value): Field Description Shows your current speed given by the GPS receiver. Shows the speed limit of the current road if the map contains it. Shows the current time corrected with time zone offset.
2.3.2 Position markers 2.3.2.1 Vehimarker and Lock-on-Road When your GPS position is available, iGO primo marks your current position with the Vehimarker. By default, this marker is a blue arrow, but you can change this icon in Settings. The exact location of the Vehimarker depends on the vehicle type used for route calculation and the navigation mode. Both can be set in Route settings (page 104). • If you choose pedestrian and/or off-road navigation: The Vehimarker is at your exact GPS position.
2.3.3.2 Turn preview and Next street When navigating a route, the top section of the Map screen shows information about the next route event (manoeuvre) and the next street or the next city/town. There is a field in the top left corner that displays the next manoeuvre. Both the type of the event (turn, roundabout, exiting motorway, etc.) and its distance from the current position are displayed. A smaller icon shows the type of the second next manoeuvre if it is near the first one.
Enter motorway. Exit motorway. Board ferry. Leave ferry. Approaching a waypoint. Approaching the destination. 2.3.3.3 Lane information and Signposts When navigating on multilane roads, it is important to take the appropriate lane in order to follow the recommended route. If lane information is available in the map data, iGO primo displays the lanes and their directions using small arrows at the bottom of the map. Highlighted arrows represent the lanes and direction you need to take.
2.3.3.4 Junction view If you are approaching a motorway exit or a complex intersection and the needed information exists, the map is replaced with a 3D view of the junction. The lanes you need to take are displayed with arrows. At the top of the screen road signs show you additional information. If you want to hide the currently displayed junction, tap the picture and the Map screen returns.
Tap any of them to display the exit area on the map. You can now easily add this exit as a waypoint to your route if needed. If you want to display other types of Places for the exits, you can change the icons in Visual Guidance settings (page 110). 2.3.3.
Streets and roads that are You can choose whether you want to use or excluded from the navigation avoid certain road types (page 104). However, when iGO primo cannot avoid such roads, the route will include them and it will show them in a colour that is different from the route colour. Streets and roads that are affected by traffic events Road segments may be affected by traffic events received.
4. Now tap any of the list items to see its details, and to display the affected road segment in its full length on the map: If there are traffic events on the recommended route that the application has not Note! bypassed, the icon will open the list of significant traffic events to let you quickly check them. 2.3.4 Manipulating the map Tap the map anywhere to browse it during navigation.
Tilting up and down , Changes the vertical view angle of the map in 3D mode. Tap the button once to modify the view in large steps, or tap and hold the button to modify it continuously and smoothly. Rotating left and right Changes the horizontal view angle of the map. , 2D or 3D view , Compass in 2D map view mode Tap the button once to modify the view in large steps, or tap and hold the button to modify it continuously and smoothly.
2.3.5 Quick menu The Quick menu is a selection of controls and functions that are frequently needed during navigation. It can be opened directly from the Map screen by tapping The menu will close after a few seconds of inactivity or if you tap . . The menu will also close if you initiate simple controls like muting the device. In other cases tapping a button will open a new screen with options. Most of these functions are shortcuts. They are accessible from the menu system.
My Route / Edit Route This button opens the route editing function. More / Settings / Route Settings (page 104) This button opens the route related settings. More / Settings / Map Settings (page 108) This button opens the map related settings. This button opens a special screen with information Tap the Current Street field on the about the current position and a button to search for nearby emergency or roadside assistance. For Map screen details, see the next chapter.
With this function you can save the active route for My Route / More / Save Route later use. With this function you can replace the active route My Route / More / Load Route with a previously saved route. With this function you can search for Places of Find / Find Places (page 46) Interest in various different ways. This button opens the Map screen and starts My Route / More / Simulate Navigation simulating the active route. (page 78) This button starts the Music player application.
2.3.6 Checking the details of the current position (Where Am I?) This screen contains information about the current position (or about the last known position if GPS reception is not available) and a button to search for useful Places nearby. You can access this screen from the map in one of the following ways: • If the current street is displayed below the Vehimarker (the current position on the map), tap it to open the Where Am I? screen. • Open the Quick menu and tap the button.
The following services can be searched around the current position or the last known position: • : Car repair and roadside assistance services • : Police stations • : Medical and emergency services • : Petrol stations Tap any of the buttons, select a Place from the list, and navigate to it.
3 On-road navigation When first started, iGO primo calculates routes using the road network of the high quality vector maps provided with the product. You can set up your route in different ways: • If you need a route for immediate navigation, you can select the destination and start navigating to it right away (normal navigation). • You can also plan a route independently of your current GPS position or even without GPS reception.
3. Tap anywhere and the hints disappear. Once you get through this screen to the search results, the hint will not appear again when you open this window later but you can see them again if you tap the information button on the right side of the input field. 4. You can see the input field at the top of the screen. Right below that you see the search area, the city/town around which the search is carried out. The default search area is the area where you are located.
7. Once the number of results is acceptable after a few seconds of searching, you can tap to switch to the result screen. 8. The result screen also opens with hints. Tap anywhere to suppress them. Once you select a destination, they will not appear again. 9. You see all results in the list, regardless of their type. Addresses, Places, Place categories, Favourite and recent destinations are mixed within one list. 10.
If you know that you will use this destination frequently, before tapping to confirm the destination, put it on the list of your Tip! Favourites first: tap then , give a name for the new Favourite, and tap to save the location. The map with the destination returns automatically. Now you can start your journey. 3.1.1.1 Combined Search - Navigating to a recent destination (History) To find one of your recent destinations in Combined Search, carry out the search as described earlier.
3.1.1.2 Combined Search - Navigating to a Favourite destination To find one of your Favourite destinations in Combined Search, carry out the search as described earlier. When you get to the result screen, do as follows: at the top of the screen. 1. Tap 2. The list is now filtered. What you see is the list of your Favourite destinations with a matching name. 3. Scroll down the list if necessary and then select one of the destinations from the list. 4.
5. After a short summary of the route parameters, the map appears showing the entire route. The route is automatically calculated. Tap parameters, or tap to modify route and start your journey. button in the The alternative way to search for an address is to tap the Destination menu. Unlike the Combined Search, this alternative search method is a structured one where you can define the parts of the address separately. Note! 3.1.1.
6. to open the list of intersections that match After entering a few characters, tap the text already entered. Scroll down the list if necessary and then select one of the streets from the list. 7. The list of intersecting streets appears. Select one street to define the intersection. As usual, you can tap 8. to enter a few characters and narrow the list. Once the destination is selected, a full screen map appears with the selected point in the middle.
4. Scroll down the list if necessary and then select one of the Places from the list. 5. Once the destination is selected, a full screen map appears with the selected point in the middle. If necessary, tap the map somewhere else to modify the destination. The Cursor ( ) appears at the new location. Tap destination, or tap 6. to confirm the to select a different destination. After a short summary of the route parameters, the map appears showing the entire route. The route is automatically calculated.
3. (optional) Should your product contain Places from different data providers, you can further narrow the list by showing Places from one provider only. Look for the provider logos at the top of the screen. Tap one of them to see Places from that provider only. 4. Scroll down the list if necessary and then select one of the Places from the list. 5. Once the destination is selected, a full screen map appears with the selected point in the middle.
3.1.2 Entering an address or a part of the address If you know at least a part of the address, it is the quickest way to select the destination of the route. Using the same screen, you can find an address by entering: • the exact address, including house number • the centre of a city/town • an intersection • the midpoint of a street • any of the above, starting the search with the postal code (page 43) 3.1.2.1 Entering an address To enter an address as the destination, do as follows: 1.
). Select results before it appears automatically, tap the city/town from the list. 5. Enter the street name: a. Tap b. Start entering the street name on the keyboard. c. Find the street you need: • . The most likely street name is always shown in the input field. To accept it, tap • .
7. A full screen map appears with the selected point in the middle. If necessary, tap the map somewhere else to modify the destination. The Cursor ( new location. Tap ) appears at the to confirm the destination, or tap to select a different destination. 8. After a short summary of the route parameters, the map appears showing the entire route. The route is automatically calculated. Tap parameters, or tap to modify route and start your journey. 3.1.2.
5. Instead of entering the house number, tap street is selected as the destination. 6. A full screen map appears with the selected point in the middle. If necessary, tap the map somewhere else to modify the destination. The Cursor ( new location. Tap . The midpoint of the ) appears at the to confirm the destination, or tap to select a different destination. 7. After a short summary of the route parameters, the map appears showing the entire route. The route is automatically calculated.
3.1.2.3 Selecting an intersection as the destination To enter an address as the destination, do as follows: 1. If you are on the Map screen, tap menu. 2. In the Navigation menu, tap the following buttons: 3. If necessary, modify the country and city/town as described earlier (page 37). 4. Enter the street name: to return to the Navigation a. Tap b. Start entering the street name on the keyboard. c. Find the street you need: • The most likely street name is always shown in the input field.
6. A full screen map appears with the selected point in the middle. If necessary, tap the map somewhere else to modify the destination. The Cursor ( new location. Tap ) appears at the to confirm the destination, or tap to select a different destination. 7. After a short summary of the route parameters, the map appears showing the entire route. The route is automatically calculated. Tap parameters, or tap to modify route and start your journey. 3.1.2.
5. Instead of entering the street name, tap . This way the centre of the displayed city/town becomes the destination of the route. 6. A full screen map appears with the selected point in the middle. If necessary, tap the map somewhere else to modify the destination. The Cursor ( new location. Tap ) appears at the to confirm the destination, or tap to select a different destination. 7. After a short summary of the route parameters, the map appears showing the entire route.
4. Enter a new city/town using its postal code: a. Tap . b. Tap to open the numeric keypad. c. Start entering the postal code. d. Find the city/town you need: • The most likely postal code is always shown in the input field. To accept it, tap • . If the desired number does not show up, open the list of results by tapping 5. . Select the postal code from the list. Enter the street name: a. Tap b. Start entering the street name on the keyboard. c. Find the street you need: • .
c. 7. to finish entering the address. (If the entered house Tap number cannot be found, the midpoint of the street is selected as the destination.) A full screen map appears with the selected point in the middle. If necessary, tap the map somewhere else to modify the destination. The Cursor ( new location. Tap ) appears at the to confirm the destination, or tap to select a different destination. 8. After a short summary of the route parameters, the map appears showing the entire route.
• You can search for both the type and the name of a road. If the same word appears in several names, for example in the name of streets, roads and avenues, you can obtain the result faster if you enter the first letter of the street type: For example, enter 'PI A' to obtain Pine Avenue and skip all Pine Streets and Pickwick Roads. • You can also search in postal codes. As postal codes consist of only a few characters, this is usually faster than entering the name of the city/town. 3.1.
3. to open the list of Places with After entering a few letters, tap names containing the entered character sequence. 4. (optional) The Places in the list are ordered by the length of the necessary detour (when navigating a route) or by their distance from the current position (when no destination is given). If you need to reorder the list, tap . 5. Browse the list if necessary and tap one of the list items. A full screen map appears with the selected point in the middle.
3.1.3.2 Searching for a Place of Interest using preset categories The Preset search feature lets you quickly find the most frequently selected types of Places. 1. If you are on the Map screen, tap menu. 2. In the Navigation menu, tap the following buttons: 3. The preset search categories appear: • to return to the Navigation , . : • If an active route exists, petrol stations are searched along the route.
• If the current position is not available either (no GPS signal), they are searched around the last known position. 4. Tap any of the quick search buttons to get an instant list of Places. 5. (optional) The Places in the list are ordered by their distance from the current or last known position, from the destination or by the length of the necessary detour. If you need to reorder the list, tap . 6. Browse the list if necessary and tap one of the list items.
3.1.3.3 Searching for a Place of Interest by category You can search for Places of Interest by their categories and subcategories. 1. If you are on the Map screen, tap menu. 2. In the Navigation menu, tap the following buttons: 3. Tap 4. Select the area around which the Place should be searched for: 5. to return to the Navigation , . . • Tap to search around the current position or if it is not available, around the last know position.
6. Select one of the main Place categories (e.g. Accommodation) or tap to list all Places around the selected location or along the route. 7. Select one of the Place subcategories (e.g. Hotel or Motel) or tap to list all Places in the selected main category around the selected location or along the route. 8. Sometimes the list of brands in the selected Place subcategory appears. Select one brand or tap to list all Places in the selected subcategory around the selected location or along the route. 9.
to see the details of the selected Place. If there is a telephone 12. (optional) Tap number saved for this Place, you can make a call to that number by tapping the green to return to the map. button at the bottom. Tap 13. If necessary, tap the map somewhere else to modify the destination. The Cursor ( ) appears at the new location. Tap destination, or tap to confirm the to select a different destination. 14. After a short summary of the route parameters, the map appears showing the entire route.
• to search for a place around the destination of the Tap active route. (The result list will be ordered by the distance from the destination.) • to search along the active route, and not around a Tap given point. This is useful when you search for a later stopover that results in a minimal detour only, such as searching for upcoming petrol stations or restaurants. (The result list will be ordered by the length of the necessary detour.) 5. (optional) If you have selected 6.
if you have not done it before. 8. Tap 9. Using the keyboard, start entering the name of the Place. 10. After entering a few letters, tap to open the list of Places with names containing the entered character sequence. 11. (optional) The Places in the list are ordered by their distance from the current or last known position, from the selected city/town, from the destination or by the length of the necessary detour. If you need to reorder the list, tap . 12.
15. After a short summary of the route parameters, the map appears showing the entire route. The route is automatically calculated. Tap parameters, or tap to modify route and start your journey. 3.1.3.5 Selecting nearby assistance from 'Where Am I?' You can quickly search for nearby assistance from the 'Where Am I?' screen. 1. On the Map screen, tap 2. Tap 3.
5. (optional) The Places in the list are ordered by their distance from the current or last known position, from the selected city/town, from the destination or by the length of the necessary detour. If you need to reorder the list, tap . 6. Browse the list if necessary and tap one of the list items. A full screen map appears with the selected point in the middle. The name and address of the Place is displayed at the top of the screen. 7. to see the details of the selected Place.
3.1.4 Searching for a Place using Google Local Search If you have an internet connection, you can search for places with the Google Local Search service. Do as follows: to return to the Navigation 1. If you are on the Map screen, tap menu. 2. In the Navigation menu, tap the following buttons: 3. Using the keyboard, start entering the text to search for.
3.1.5 Selecting a map location as the destination 1. If you are on the Map screen, tap menu. to return to the Navigation 2. In the Navigation menu, tap the following buttons: , , . 3. Locate your destination on the map: move and scale the map as needed. 4. Tap the location that you want to select as your destination. The Cursor ( appears there. 5. Tap 6. After a short summary of the route parameters, the map appears showing the entire to select the Cursor as the destination. route.
3.1.6 Selecting the destination from your Favourites You can select a location that you have already saved as a Favourite to be your destination. Adding a location to the list of Favourite destinations is described on page 74. 1. Access the list of Favourites: • If you are on the Map screen, tap • If you are in the Navigation menu, tap to open the Quick menu. . . The list of Favourite destinations is displayed. 2. Tap 3. Tap the Favourite that you want to set as your destination.
3.1.7 Selecting one of the most likely destinations (Smart History) The destinations that you have set earlier appear in the History list. Two of those recent destinations are shown in the Destination menu for easy access. Smart History offers these locations based on your navigation habits, using parameters like the current time of day, the day of week, and the current location. The more you use the navigation software, the better it can guess your desired destination. to return to the Navigation 1.
3.1.8 Selecting a recent destination from the History The destinations that you have set earlier appear in the History. 1. Access the History: • If you are on the Map screen, tap • If you are in the Navigation menu, tap and then tap . and then tap . 2. The list of recent destinations appears. Smart History promotes three destinations to the first page based on your previous routes (most likely destinations). The rest of the destinations are ordered by time they were last selected.
3.1.9 Entering the coordinate of the destination You can also select a destination by entering its coordinate. Do as follows: 1. If you are on the Map screen, tap menu. 2. In the Navigation menu, tap 3. Open the 4. You can enter the latitude and longitude values in any of the following formats: decimal degrees; degrees and decimal minutes; or degrees, minutes and decimal seconds. 5. (optional) If necessary, tap the coordinate in UTM format. 6. When finished, tap 7.
3.1.10 Navigate to a location stored in a photo You can also set the location stored in a photo as your destination. Do as follows: . 1. In the More menu, tap 2. The photos stored in the device appear. Select one photo to set its location as the destination. 3. A full screen map appears with the selected point in the middle. If necessary, tap the map somewhere else to modify the destination. The Cursor ( new location.
3.1.11 Building a route from the list of destinations (Create Route) You can also build your route destination by destination from the My Route menu. 1. If you are on the Map screen, tap menu. 2. In the Navigation menu, tap 3. Tap 4. There is only one line in the list of route points, the start point of the route, normally the current GPS position. 5. Tap 6. The Destination menu appears and you can select the destination of the route the same way as described in the previous sections. 7.
3.2 Viewing the entire route on the map It is easy to get a map overview of the active route. Do as follows: 1. If you are on the Map screen, tap menu. 2. In the Navigation menu, tap 3. Tap . The active route is displayed in its full length on the map together with additional information and controls. to return to the Navigation . 3.3 Checking route parameters and accessing route related functions You can check different parameters of the route recommended by iGO primo. 1.
4. You have the following options on this screen (for detailed instructions on how to use them, see the next chapter): • Tap to edit the route: to add or remove destinations or change their sequence. You can also set a route start point other than your current location. This can be useful to plan and save a future trip. • Tap to display the entire route on the map. • Tap to bypass a part of the route. • Tap to delete the active route.
• to add the newly selected location as an intermediate destination to your Tap route. The other destinations of the route remain intact. Note: the new waypoint is placed among destinations to keep the route optimal. To decide where a waypoint to appear, use the Edit Route feature. • to append the newly selected destination at the end of the route. The Tap other destinations of the route remain intact. The previous final destination is now the last waypoint. 3.4.
and 4. The first line is the start of the route, normally the current GPS position. Tap confirm your action at the warning message. 5. The Destination menu appears and you can select the start point of the route the same way you select a destination. 6. When the new start point is set, tap 7. The map returns with a transparent Vehimarker (showing that there is no GPS reception). If an active route already existed, it is now recalculated starting from the selected location. 8.
4. You have the following options: • Tap to add a new destination. • Tap to delete a destination. • Tap to modify the start point of the route. • Tap to reorder the list. You can do it manually or you can let the application optimise the route for you. 3.4.4 Pausing the active route You do not need to pause the active route: when you start driving again, iGO primo restarts the voice instructions from your position. 3.4.
3.4.6 Checking route alternatives when planning the route You can select from different route alternatives or change the route planning method after you have selected a new destination. Do as follows: 1. Select a destination as explained earlier, and get to the route confirmation screen. 2. Tap . 3. Tap . 4. You see the basic details of three route alternatives with the selected route planning method. Tap any of them to see it on the map. 5.
3.4.7 Checking route alternatives for an existing route To recalculate the active route with a different route planning method, you can modify the Route settings (page 104). There is another way to do this and to compare different route alternatives with the same route planning method. Do as follows: to return to the Navigation 1. If you are on the Map screen, tap menu. 2. In the Navigation menu, tap 3. Tap . 4. Tap . 5.
7. for a few Select one of the route alternatives then tap and hold seconds to return to the Map screen. iGO primo recalculates the route. The orange line now shows the new recommended route. 3.4.8 Changing the vehicle used in route planning To recalculate the active route for a different vehicle, do as follows. These changes can also be made in Settings (page 104). 1. On the Map screen, tap 2. Tap and then tap . and then tap one of the following: • • • • • • • 3.
3.4.9 Changing the road types used in route planning To recalculate the active route with different road type preferences, do as follows. These changes can also be made in Settings (page 104). and then tap . 1. On the Map screen, tap 2. Tap any of the listed road types to modify the route. If needed, scroll the list for all road types. You have the following options (their order depends on the selected vehicle type): 3.
3.5 Saving a location as a Favourite destination You can add any location to Favourites, the list of frequently used destinations. Planning a route to one of the Favourite destinations is described on page 59. 1. Select a destination as described before. It can be an address, a Place, any location on the map, a previously used destination from History, etc. 2. When the full screen map appears with the selected location in the middle, tap . 3. Tap 4.
3.5.1 Editing the details of a Favourite destination You can select a location that you have already saved as a Favourite and edit its details. Adding a location to the list of Favourite destinations is described on page 74. 1. Access the list of Favourites: • If you are on the Map screen, tap • If you are in the Navigation menu, tap and then tap . and then tap . 2. The list of Favourite destinations is displayed. 3. Tap the Favourite that you want to edit.
3.6 Saving a map location as an alert point You can save any map location as an alert point (for example a speed camera or a railway crossing). 1. Browse the map and select a location. The red Cursor appears there. 2. Tap 3. Scroll down the list and tap 4. On the newly opened screen, select the type of the alert point, the direction from which you expect the alert, and (if applicable) the speed limit for this alert point. 5. Tap . . to save the location as a new alert point.
3.7 Saving the current location as an alert point It is even easier to save the current map location as an alert point (for example a speed camera or a railway crossing). button on the Map screen. 1. Tap the 2. On the newly opened screen, select the type of the alert point, the direction from which you expect the alert, and (if applicable) the speed limit for this alert point. 3. Tap to save the location as a new alert point. 3.
5. Tap to save the changes to the alert point. 3.9 Watching the simulation of the route You can run a simulated navigation that demonstrates the active route. Do as follows: 1. If you are on the Map screen, tap menu. 2. In the Navigation menu, tap 3. Tap to return to the Navigation . .
4. . The simulation starts from the starting Scroll down the list and tap point of the route, and using a realistic speed, it leads you through the whole recommended route. 1. (optional) You have the following controls during the simulation (the control buttons disappear after a few seconds but you can open them again if you tap the map): • : Jump to the next route event (manoeuvre). • : Pause the simulation. • : Jump to the previous route event (manoeuvre). • 2.
4 Off-road navigation When first started, iGO primo calculates routes using the road network of the high quality vector maps provided with the product. You can switch the application to off-road mode in Navigation settings in one of the following ways: • then • , From the Main menu, tap , and . From the Map screen, tap , and then . Most of the procedures described for on-road navigation also apply to off-road navigation.
5 Lorry navigation The navigation software gives more options for lorry drivers: • You can enter the parameters of your vehicle and iGO primo calculates your routes with taking available weight, height, etc.
4. Tap 5. There is one Default Lorry profile at the end of the list. You can either: 6. 7. . • tap the • create a new profile by tapping and selecting Lorry as the vehicle type. button at the Default Lorry profile or then The list of vehicle profile parameters appear. Scroll the list and tap any of the lines to change the parameters. The parameters are intuitive.
Tip! Speed limits for lorries may not be available for all roads. It is advised to enter the maximum allowed speed in your area for your vehicle instead of the maximum speed your lorry is capable of.
5.3 Setting up driving time alerts In order to obey the regulations regarding continuous and daily driving, you can set countdown timers to alert you when you need a break or a sleep. This feature can be set for one driver or two alternate drivers. to return to the Navigation 1. If you are on the Map screen, tap menu. 2. In the Navigation menu, tap 3. Tap . 4. Tap and set the driving timer defaults for the driver. 5. (optional) Tap the switch to use the vehicle with two drivers.
from the moment when the vehicle stopped). When the vehicle is in motion again, the break timer is reset, and both driving timers start counting down again.
6 Reference Guide On the following pages you will find the description of the different concepts and menu screens of iGO primo. 6.1 Concepts 6.1.1 Smart Zoom Smart Zoom provides much more than just a usual automatic zoom feature: • While following a route: when approaching a turn, it will zoom in and raise the view angle to let you easily recognise your manoeuvre at the next junction.
This feature can be turned off in Settings (page 110). 6.1.4 Route calculation and recalculation iGO primo calculates the route based on your preferences: • • Route planning methods: • : Gives a quick route if you can travel at or near the speed limit on all roads. Usually the best selection for fast and normal cars. • : Gives a route that has the smallest total distance of all possible routes. It can be practical for slow vehicles.
• • Speed limits are not used in route calculation and an average walking speed is used when calculating the estimated time of arrival. : • Manoeuvre restrictions and directional constraints (if they are applied to bicycles in the map data) are taken into account when planning a route. • Roads are used only if access for bicycles or pedestrians is allowed. • Controlled-access roads are excluded from routes. • A private road is used only if the destination is there.
• Road types used or avoided in route calculation: • • • • • Whenever data exist, route calculation takes into account statistical traffic data for the given day of week and time of day (page 93). Real-time Traffic events are also taken into account and sometimes greatly modify the route. iGO primo automatically recalculates the route if you deviate from the proposed itinerary or if a newly received Traffic event concerns a part of the recommended route.
Tap the field with these details to switch the route to Green immediately. 6.1.6 Road safety cameras and other proximity alert points There is a special proximity warning for road safety cameras (like speed or red light cameras) and other proximity alert points (like schools or railroad crossings). These alert points are not part of iGO primo. You can download them from www.naviextras.com or you can upload points in a specific text file if needed.
6.1.7 Speed limit warning Maps may contain information about the speed limits of the road segments. iGO primo is able to warn you if you exceed the current limit. This information may not be available for your region (ask your local dealer), or may not be fully correct for all roads in the map. The maximum speed set in the vehicle profile is also used for this warning. iGO primo alerts you if you exceed the preset value even if the legal speed limit is higher.
In the top right corner, the GPS reception quality icon shows the current accuracy of the position information. Icon Description iGO primo has no connection to the GPS receiver: GPS navigation is not possible. Devices with a built-in GPS receiver are permanently connected. On such devices, the icon does not appear in normal circumstances. iGO primo is connected to the GPS receiver, but the signal is too weak and the receiver cannot determine the GPS position. GPS navigation is not possible.
6.1.9.1 Historical traffic If statistical traffic information is stored with the map data, iGO primo can take them into account when planning a route. In normal cases, these statistics help you avoid usual traffic jams on the given day of week in the given hour but in some cases like on public holidays that fall on normal weekdays, they can be misleading. You can disable this feature in Traffic settings (page 103).
1. Tap 2. Tap 3. Tap the traffic category you are interested in, or tap of all events: 4. Now tap any of the list items to see its details, and to display the affected road segment in its full length on the map: to open the Traffic Summary screen: to open the list of of event categories. to see the list If there are traffic events on the recommended route that the application has not Note! bypassed, the icon will open the list of significant traffic events to let you quickly check them.
6.1.9.3 Online traffic information Unlike statistical traffic information, online traffic can provide you with the real-time status of the traffic. Route calculation can avoid road blocks or unexpected traffic jams caused by an accident. Note! This feature needs an active internet connection. The application automatically takes into account the traffic events received. You do not need to set anything in the program.
4. Now tap any of the list items to see its details, and to display the affected road segment in its full length on the map: If there are traffic events on the recommended route that the application has not Note! bypassed, the icon will open the list of significant traffic events to let you quickly check them. 6.2 'More' menu The 'More' menu provides you with various options and additional applications. Tap the following buttons: , . Button Description Visit www.naviextras.
Tap this button if you have a redeemable code that activates online services to your connected device. Enter the code when your device is connected to the Internet and the application will activate the services online. The scientific calculator helps you in all your calculation needs. Tap the Mode button for additional functions and use the memory to save your results. The Fuel consumption monitor helps you keep track of the consumption of your car even if you do not use navigation for all your journeys.
Button Description Adjust the sound volume, mute your device or change the voice guidance language. In addition, you can enable and set up different warnings and alerts. The content of the Quick menu (page 23) is fully customisable. Tap the button you want to change, and select its new function from the list. To calculate a better arrival time, it is necessary to include the waiting or loading times spent at each waypoint.
Modify the basic software parameters set during the initial setup process. For details, see page 7. Delete all saved data and reset all settings to their factory defaults. 6.3.1 Sound and Warnings Adjust the sound volume, mute your device or change the voice guidance language. In addition, you can enable and set up different warnings and alerts. Button Description Tap this button to adjust the volume of the different sounds in the application.
Tap this button to set the verbosity of the voice instructions: how much they tell and how often they speak. Maps may contain information about the speed limits of the road segments. iGO primo is able to warn you if you exceed the current limit. This information may not be available for your region (ask your local dealer), or may not be fully correct for all roads in the map. The maximum speed set in the vehicle profile is also used for this warning.
This feature allows you to receive a warning when approaching a Road Safety Camera or other alert points like school zones or railroad crossings. You must ensure on your own liability that using this feature is legal in the country where you intend to use it. You can choose what alert point sources you want to use. • Community alert points can be uploaded to your device in every few minutes if you have an internet connection. This dynamic information comes from navigation users like you.
You can control the volume of the following sound types: Button Description This is the main volume control. These controls affect all below sounds. They can also be accessed from the Quick menu. These controls affect the volume of the guidance sounds (verbal instructions). Turn off the attention tone preceding verbal instructions or adjust its volume. These controls affect the volume of the non verbal alert sounds (beeps). These controls affect the volume of the background music.
6.3.3 Driving time management To calculate a better arrival time, it is necessary to include the waiting or loading times spent at each waypoint. Driving timers allow you to be warned when you need a rest or you have driven enough for the day. You have the following options: Button Description Turn this switch on to be able to set the waiting time for all waypoints of the route. This way the arrival time calculation can take into account the idle times at intermediate destinations.
6.3.5 Route settings These settings determine how routes will be calculated. Button Description You can set the type of vehicle you will use to navigate the route. Based upon this setting, some of the road types can be excluded from the route, or some of the restrictions may not be taken into account in route calculation. You can edit the parameters of the selected vehicle profile, or you can even create new vehicle profiles if you tap More.
Vehicle profiles: When you first tap the following options: , you see the list of default vehicle profiles. You have Button Description You can edit the parameters of the vehicle profile. Tap this button to reveal the below options. Tap this button to create your own vehicle profile. Tap this button to reset all vehicle profiles to their default settings. When creating a new vehicle profile, first you need to select the vehicle type.
Set the maximum allowed weight of the vehicle. Set the actual weight of the vehicle. Select one or more hazard types if the vehicle carries dangerous material. Vehicle types: When creating a new vehicle profile, select one of the below vehicle types. Besides the below mentioned conditions, dimension, weight and freight hazard restrictions can also be taken into account when planning a route. • : • Manoeuvre restrictions and directional constraints are taken into account when planning a route.
• Directional constraints are taken into account the way that opposite direction is allowed with a low speed. • A private road is used only if the destination is there. • Walkways are excluded from routes. • : • Manoeuvre restrictions and directional constraints are taken into account when planning a route. • Roads are used only if access for buses is allowed. • Private roads, resident-only roads and walkways are excluded from routes.
For vehicle types where Green routing is not available, this method combines the benefits of Fast and Short: iGO primo calculates as if it were calculating the Fast route, but it takes other roads as well to save fuel. Results in a route with fewer turns and no difficult manoeuvres. With this option, you can make iGO primo to take, for example, the motorway instead of a series of smaller roads or streets. 6.3.
When selected, the map zooms out to show an overview of the surrounding area if the next route event (manoeuvre) is far. When you get close to the event, the normal map view returns. Switch between daytime and night colour modes or let the software switch between the two modes automatically a few minutes before sunrise and a few minutes after sunset. Select the colour scheme used in daytime mode. Select the colour scheme used in night mode.
6.3.8 Visual guidance settings Adjust how the software helps you navigate with different kinds of route related information on the Map screen. The data fields in the corner of the Map screen can be customised. Tap this button and select the values you want to see. The values can be different when you navigate a route from when you are just cruising without a given destination.
When you slow down while driving on a motorway, there is a chance that you are in a traffic jam so iGO primo offers you a detour using the next exit. The message shows you distance of the exit and the difference in distance and estimated time compared to the original route. You can choose from one of the following options: • Tap Dismiss or just ignore the message if you want to keep the original route. • Tap Preview to see the overview of the original route and the detour to make the decision.
6.3.10 Regional settings These settings allow you to customise the application for your local language, measurement units, time and date settings and formats, as well as to choose the time zone. Button Description This button displays the current written language of the user interface. By tapping the button, you can select a new language from the list of available languages. The application will restart if you change this setting; you are asked to confirm this.
6.3.12 Log on to receive community content In order to receive online community data, you need to register a user account and log on to the system. See page 7 for details. Log on with your user name and PIN code here. The next time the application is started, you will be automatically logged on if internet connection is available. 6.3.13 Bandwidth management Frequently using online services may excessively use your internet connection.
6.3.14 Log collection settings If you accept this when first using the application, it collects usage information and GPS logs that may be used for improving the application and the quality and coverage of maps. The data is processed anonymously; no one will be able to track any personal information. Here you can enable or disable collecting these logs. Anonymous statistical information on using the navigation software is collected for later development purposes.
7 Glossary 2D/3D GPS reception The GPS receiver uses satellite signals to calculate its (your) position and needs at least four signals to give a three-dimensional position, including elevation. Because the satellites are moving and because objects can block the signals, your GPS device might not receive four signals.
North-up map orientation In North-up mode the map is rotated so its top always faces North. This is the orientation for example in Find on Map. Road Safety Camera Special alert points for speed, red light or bus lane cameras. Different data sources are available. You can configure iGO primo to warn you when you approach one of these cameras. Detecting the location of Road Safety Cameras is prohibited in certain countries.
8 End User Licence Agreement 1 The contracting parties 1.1 This Agreement has been entered into by and between NNG Software Developing and Commercial Ltd. (registered seat: 23 Bérc utca, H-1016 Budapest, Hungary; company reg.no.: 01-09-891838) as Licensor (hereinafter: Licensor) and You as the end user (hereinafter: User; the User and the Licensor jointly referred to as: Parties) in subject of the use of the products specified in this Agreement, including software products, databases and content .
4.5. Your rights under this Agreement will terminate immediately without notice from Licensor if you materially breach it or take any action in derogation of Licensor's and/or its licensors' rights to the Software Product. Licensor may terminate this Agreement if any Software Product becomes, or in Licensor's reasonable opinion likely to become, the subject of a claim of intellectual property infringement or trade secret misappropriation.
7.1.6 to modify, extend, transform the Software Product (in whole or in part), to separate it into parts, combine it with other products, install it in other products, utilize it in other products, not even for the purpose of achieving interoperability with other devices; 7.1.
8.6 The Licensor also draws the attention of the User to the fact that, when using the Software Product in any form of vehicle, observing the traffic regulations and rules (e.g. use of obligatory and/or reasonable and suitable security measures, proper and generally expected care and attention in the given situation, and special care and attention required due to the use of the Software Product) is the exclusive responsibility of the User.
10 Anonymous data collection 10.1 The User hereby acknowledges that the Software Product may collect, transmit to Licensor or third parties, and in some cases store data connected to the usage of the Software Product by the User (e.g. movement/route data, user interaction data). Such data collection functions may be disabled or enabled by User any time from within the corresponding menu.
enabling Online Content, User accepts compliance with those third party terms and conditions. 11.7 Discontinuation. Licensor reserves the right to discontinue provision or access to any Online Content Service with or without prior notice to the User. Such discontinuation shall not entail any consequences other than here stated. In case of discontinued Online Content Services that were (i) provided for a pre-paid fee, AND (ii) such fee covers the use of the Online Content Service for a definite term (i.e.
9 Copyright note The product and the information contained herein are subject to change without prior notification. This manual may not, in whole or in part, be reproduced or transmitted in any form either electronically or mechanically, including photocopying and recording, without the express written consent of NNG Global Services Kft.. © 2012 - NNG Global Services Kft. © 2012 NAVTEQ. All rights reserved.
