User Manual

Prima di operare
6 BM14S II
Collegare un singolo subwoofer
4. Getting started
Dynaudio Acoustics BM14S 7
Connecting a single subwoofer
Connecting as LFE channel (1)
X Connect subwoofer to LFE/Slave input.
Connecting as subwoofer for satellites (2)
X Connect full bandwidth signal to SAT/SUB input.
Sub reproduces sum of right and left signal.
X Set the Mode switch to LFE.
Multiple subwoofer connections
The BM14S can be used stand-alone or together with multiple subwoofer units.
Using multiple units may be helpful if the listening room is quite large or has difficult
acoustic conditions.
When using two or more subwoofers, the first one (designated “Master”) controls the
following subs (designated “Slave”) via a subwoofer cable.
To connect multiple subwoofers:
1. Connect the first subwoofer as described before.
2. Set Mode switch of first subwoofer to LFE.
3. From the Slave output of the first subwoofer connect a XLR cable to the
LFE/Slave input of the following subwoofer. This one now becomes the slave.
4. Set the Mode switch of the second subwoofer to Slave.
X Further subwoofers can be connected in the same way. Set the Mode switch of
all following subwoofers to Slave respectively.
Note: • You can also use both connection types. The signals will be combined in
the BM14S and routed accordingly. This allows the BM14S to reproduce
both the LFE channel information as well as the bass range of the
connected satellite system.
• Use Slave mode if you want to use an external bass management
system.
Note: • When using multiple subwoofers in a Master-Slave setup, it is
recommended that the subwoofers are all the same model.
• If you wish to use multiple subwoofers with full individual control, set the
Input switch for all to the LFE position. From the source subwoofer
output, use a Y-connector.
1
2
LFE
Stereo
Sub 1
(Master)
Sub 2
(Slave)
Sub...
(Slave)
LFE
Stereo
Collegamento come canale LFE (1)
– Collega il subwoofer all’ingresso LFE/Slave.
Collegamento come unità per satelliti (2)
– Collega il segnale full bandwidth all’ingresso SAT/SUB.
Il sub riprodurrà la somma dei segnali Left e Right.
– Imposta il selettore Mode su LFE.
Note:
– È possibile impiegare entrambi i tipi di collegamenti. I se-
gnali saranno combinati all’interno dell’unità BM14S II e
reindirizzati conformemente. Ciò consente al sub di ripro-
durre sia le informazioni del canale LFE, sia la gamma
delle basse frequenze del sistema satellite collegato.
– Usa la modalità Slave se intendi impiegare un sistema di
bass management esterno.
Collegare molteplici unità subwoofer
4. Getting started
Dynaudio Acoustics BM14S 7
Connecting a single subwoofer
Connecting as LFE channel (1)
X Connect subwoofer to LFE/Slave input.
Connecting as subwoofer for satellites (2)
X Connect full bandwidth signal to SAT/SUB input.
Sub reproduces sum of right and left signal.
X Set the Mode switch to LFE.
Multiple subwoofer connections
The BM14S can be used stand-alone or together with multiple subwoofer units.
Using multiple units may be helpful if the listening room is quite large or has difficult
acoustic conditions.
When using two or more subwoofers, the first one (designated “Master”) controls the
following subs (designated “Slave”) via a subwoofer cable.
To connect multiple subwoofers:
1. Connect the first subwoofer as described before.
2. Set Mode switch of first subwoofer to LFE.
3. From the Slave output of the first subwoofer connect a XLR cable to the
LFE/Slave input of the following subwoofer. This one now becomes the slave.
4. Set the Mode switch of the second subwoofer to Slave.
X Further subwoofers can be connected in the same way. Set the Mode switch of
all following subwoofers to Slave respectively.
Note: • You can also use both connection types. The signals will be combined in
the BM14S and routed accordingly. This allows the BM14S to reproduce
both the LFE channel information as well as the bass range of the
connected satellite system.
• Use Slave mode if you want to use an external bass management
system.
Note: • When using multiple subwoofers in a Master-Slave setup, it is
recommended that the subwoofers are all the same model.
• If you wish to use multiple subwoofers with full individual control, set the
Input switch for all to the LFE position. From the source subwoofer
output, use a Y-connector.
1
2
LFE
Stereo
Sub 1
(Master)
Sub 2
(Slave)
Sub...
(Slave)
LFE
Stereo
Il BM14S II può essere usato come unità stand-alone oppure
insieme a diverse unità subwoofer. L’uso di molteplici unità
sub può essere utile se la sala d’ascolto è di dimensioni relati-
vamente grandi oppure presenta condizioni acustiche difcili.
Nell’utilizzo di due o più unità subwoofer, la prima (che sarà
designata come “Master”) controllerà le unità sub successive
(designate come “Slave”), tramite un cavo subwoofer.
Per collegare molteplici unità sub:
1. Collega il primo subwoofer come descritto in precedenza.
2. Imposta il selettore Mode del primo subwoofer su LFE.
3. Usa un cavo XLR per collegare l’uscita Slave del primo
subwoofer all’ingresso LFE/Slave del subwoofer succes-
sivo (il quale ora diventerà l’unità Slave).
4. Imposta il selettore Mode della seconda unità sub su Sla-
ve.
Ulterori unità sub possono essere collegate allo stesso modo;
imposta il selettore Mode di tutte le unità successive su Slave.