BM6 mkIII – Owner’s manual
Introduction Introduction Important safety instructions The lightning flash with an arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Introduction – Be advised that different operating voltages require the use of different types of line cord and attachment plugs. – Always observe the local safety regulations. Ensure that the factory-set power requirements for the device (refer to the label on the back of the monitor) corresponds to the mains supply in your region. – This equipment should be installed near the socket outlet and disconnection of the device should be easily accessible.
Introduction Owner’s manual 3
Introduction Introduction Congratulations on your purchase of the Dynaudio Professional BM6 mkIII active monitor system. With the right care and attention it will provide many years of excellent and trouble-free audio reproduction. It is most important, however, that you take a few minutes at this early stage of your monitor’s life to read this manual. It contains essential information to help you get the best from your new monitors.
Operation Operation Overview – rear panel Correct setup and connections is essential to achieve optimal performance from your monitors. Please follow the instructions on the following pages. 1. 2. 3. 4. 5. 6. 7. 8.
Operation Setting up 1/2. Power on/off switch / AC power in Before switching on, make sure Mains Voltage matches your areas Mains Voltage specification. Replace fuse only with the fuse-type marked on the rear-panel label. 3. Balanced analog input Audio Input is via a fe1:0 2 1 male XLR connector. 2:+ 3 3:The Input is electronically balanced with following connections. The connections are printed on the rear for easy reference.
Operation sound is too bright, try to set to -1 dB to reduce treble by 1 dB. If the sound is too dull, use +1 dB setting to raise the treble by 1 dB. Indicators On the front you will find two diodes. These are positioned just above the Dynaudio Logo. 1. The green power diode indicates speaker on/off status. Green indicates “power on”. 2. The second diode has two functions. When the output stage is close to clipping the LED will light up orange. And it will light up red when the amplifier gets too hot.
Miscellaneous Miscellaneous Troubleshooting – If the Power LED lights green and there is no sound, check your input signal, e.g. by switching speakers. – If the Power LED does not light at all and there is no sound, check the fuse. If you have replaced the fuse and there still is no sound, contact your Dynaudio Professional Dealer. – If the protection LED lights red, check the temperature of the heat sink.
Warranty Warranty Dynaudio Professional products are warranted to be free from defects in components and factory workmanship under normal use and service for a period of two (2) years when bought from a reseller within the EU. Dynaudio Professional products are warranted to be free from defects in components and factory workmanship under normal use and service for a period of one (1) year when bought from a reseller outside the EU.
Technical specifications Technical specifications System Two-way Active Near-field Monitor Frequency Response (+/- 3 dB) 40 Hz to 21 kHz Input level for 85 dB SPL @ 1 m -14 dBu RMS @ 0 dB setting Input Impedance 65 kOhm each branch Power consumption Idle: 15 W / Max: 130 W Amplifier power Tweeter: 50 W / Woofer: 100 W Max SPL 1m, pair 119 dB peak Max SPL 2m, 5.1 120 dB peak Bass Principle Bass reflex Vent tuning frequency 37 Hz Internal Cabinet Volume 11.
© Dynaudio A/S, 8660 Skanderborg, Denmark Owner’s Manual BM6 mkIII 0214 – item no. 455431 All text and image copyrights reserved. Subject to change without notice. www.dynaudioprofessional.
