Operating instructions
Swim Spa Operator’s Guide
(XM.ce) WIRING CONNECTIONS
ELECTRICAL WIRING
An IEC certied bushing that will maintain the IPX5 rating must be used. The power cord must
be in accordance with the national electrical code of the country in which the in.xm is to be
installed.
*Dual-phase system: Two electrical phases out of a three-phase power system. It’s important
to note that on a polyphase power system, all electrical phases must share the same neutral.
11
in.xm.ce
connections
An IEC certified bushing that will maintain the IPX5 rating must be used. The power cord must be in
accordance with the national electrical code of the country in which the in.xm.ce is to be installed.
*Dual-phase system
: two electrical phases out of a three-phase power system. It's important to note
that on a polyphase power system, all electrical phases must share the same neutral.
1 x 230 VAC (1 x 32A) Single-phase 1 x 230 VAC (2 x 16A) Dual-phase*
1 x 230 VAC (3 x 16A) Three-phase
Electrical wiring
11
in.xm.ce
connections
An IEC certified bushing that will maintain the IPX5 rating must be used. The power cord must be in
accordance with the national electrical code of the country in which the in.xm.ce is to be installed.
*Dual-phase system
: two electrical phases out of a three-phase power system. It's important to note
that on a polyphase power system, all electrical phases must share the same neutral.
1 x 230 VAC (1 x 32A) Single-phase 1 x 230 VAC (2 x 16A) Dual-phase*
1 x 230 VAC (3 x 16A) Three-phase
Electrical wiring
11
in.xm.ce
connections
An IEC certified bushing that will maintain the IPX5 rating must be used. The power cord must be in
accordance with the national electrical code of the country in which the in.xm.ce is to be installed.
*Dual-phase system
: two electrical phases out of a three-phase power system. It's important to note
that on a polyphase power system, all electrical phases must share the same neutral.
1 x 230 VAC (1 x 32A) Single-phase 1 x 230 VAC (2 x 16A) Dual-phase*
1 x 230 VAC (3 x 16A) Three-phase
Electrical wiring
POWERING UP THE UNIT
13
in.xm.ce
powering up the unit
Make sure all accessories
are linked to the bonding
connector and connected
to the pack.
Make sure the spa pack door is
closed.
Turn on the breaker.
It's important to specify the
phase configuration setting
at the power supply : Single-
phase (1P), Dual- phase (2P) or
Three-phase (3P).
Press Select button to select
the proper phase configuration
setting.
The in.scan display will show
"x P", with "x" representing
the number of phases of the
electric power system.
RCD Br
1 X 32 A 1 P
2 X16 A 2P
3 X 16 A 3 P
Bonding lug
Use Change button to go from
one parameter to the next.
Press Select button again to
make the correct selection.
All receptacles will match
the corresponding female
connection on the spa pack.
No connectors should remain
unplugged. Use blank plugs to
fill unused connectors.
13
in.xm.ce
powering up the unit
Make sure all accessories
are linked to the bonding
connector and connected
to the pack.
Make sure the spa pack door is
closed.
Turn on the breaker.
It's important to specify the
phase configuration setting
at the power supply : Single-
phase (1P), Dual- phase (2P) or
Three-phase (3P).
Press Select button to select
the proper phase configuration
setting.
The in.scan display will show
"x P", with "x" representing
the number of phases of the
electric power system.
RCD Br
1 X 32 A 1 P
2 X16 A 2P
3 X 16 A 3 P
Bonding lug
Use Change button to go from
one parameter to the next.
Press Select button again to
make the correct selection.
All receptacles will match
the corresponding female
connection on the spa pack.
No connectors should remain
unplugged. Use blank plugs to
fill unused connectors.
13
in.xm.ce
powering up the unit
Make sure all accessories
are linked to the bonding
connector and connected
to the pack.
Make sure the spa pack door is
closed.
Turn on the breaker.
It's important to specify the
phase configuration setting
at the power supply : Single-
phase (1P), Dual- phase (2P) or
Three-phase (3P).
Press Select button to select
the proper phase configuration
setting.
The in.scan display will show
"x P", with "x" representing
the number of phases of the
electric power system.
RCD Br
1 X 32 A 1 P
2 X16 A 2P
3 X 16 A 3 P
Bonding lug
Use Change button to go from
one parameter to the next.
Press Select button again to
make the correct selection.
All receptacles will match
the corresponding female
connection on the spa pack.
No connectors should remain
unplugged. Use blank plugs to
fill unused connectors.
Bonding lug
1 x 230 VAC
(1 x 32A) Single-phase
x 230 VAC (2 x
16A) Dual-phase
1 x 230 VAC (3 x
16A) Three-phase
Make sure all accessories are linked to the bonding connector and
connected to the pack.
Make sure the swim spa pack door is closed.
Turn on the breaker.
It’s important to specify the phase conguration setting at the power
supply: Single-phase (1P), Dual- phase (2P) or Three-phase (3P).
Press select button to select the proper phase conguration setting.
The in.scan display will show “x P”, with “x” representing the number
of phases of the electric power system.
RCD Br
1 X 32 A 1 P
2 X16 A 2P
3 X 16 A 3 P
Use change button to go from one parameter to the next.
Press select button again to make the correct selection.
All receptacles will match the corresponding female connection on
the swim spa pack.
No connectors should remain unplugged. Use blank plugs to ll
unused connectors.
18