User's Manual

12 of 19 AP2 RF Transceiver Module
228 River Avenue, Cochrane, Alberta, Canada T4C 2C1 thisisant.com
3 Electrical Specifications
A
bsolute Maximum Ratings
V
oltage applied at
V
CC
to
V
SS
-0.3V to +3.6V
Input voltage at any pin -0.3V to
V
CC
+ 0.3V; max +3.6V
Operating temperature -40ºC to +85ºC
Storage temperature -40ºC to +85ºC
Note: Stress exceeding one or more of the above maximum ratings may cause permanent damage.
Conditions: V
CC
= +3.0V, V
SS
= 0V, T
A
= - 40ºC to +85ºC
Symbol Parameter (condition) Notes Min Typ. Max Units
Operating conditions
V
CC
Supply voltage 1.9 3.0 3.6
V
T
A
Operating temperature -40 +85 ºC
Digital input pin
V
IH
HIGH level input voltage 0.7
V
CC
V
CC
V
V
IL
LOW level input voltage
V
SS
0.3
V
CC
V
Digital output pin
V
OH
HIGH level output voltage (I
OH
=-0.5mA)
V
CC
-
0.3
V
CC
V
V
OL
LOW level output voltage (I
OL
=0.5mA)
V
SS
0.3
V
General RF conditions
f
OP
Operating frequency 1) 2400
2403-
2480
2483.5 MHz
PLL
res
PLL Programming resolution 1 MHz
f
XTAL
Crystal frequency 16 MHz
Δf
Frequency deviation ±160 kHz
R
GFSK
Air data rate in each burst on-air 1 Mbps
F
CHANNEL
Non-overlapping channel spacing 1 MHz
Transmitter operation
P
RF
Maximum output power 2) 0 +4 dBm
P
RFC
RF power control range 16 18 20 dB
P
RFCR
RF power accuracy ±4 dB
P
BW
20dB bandwidth for modulated carrier 950 1100 kHz
P
RF1.1
1st adjacent channel transmit power 1MHz -20 dBc
P
RF2.1
2nd adjacent channel transmit power 2MHz -40 dBc
Receiver operation
RX
MAX
Maximum received signal at <0.1% BER 0 dBm
RX
SENS
Sensitivity at 0.1% BER -85 dBm
C/I
CO
C/I co-channel 9 dBc
C/I
1ST
1st adjacent channel selectivity C/I 1MHz 8 dBc
C/I
2ND
2nd adjacent channel selectivity C/I 2MHz -20 dBc
C/I
3RD
3rd adjacent channel selectivity C/I 3MHz -30 dBc
Current Consumption
I
Dee
p
Slee
p
Deep sleep command 0.5 µA
I
Idle
No active channels
–
no communications 2.0 µA
I
Sus
p
end
Asynchronous suspend activated 2.0 µA
I
Base_32kXO
Base Active current (32.768 KHz crystal oscillator
or external clock source)
3.0 µA
I
Base_32kSynt
Base Active current (using internal synthesized
clock source)
0.1 mA
I
PeakTX
Peak Tx current @ 0dBm output power 3) 15 mA
I
PeakTX-6
Peak Tx current @ -6dBm output power 3) 13 mA
I
PeakTX-12
Peak Tx current @ -12dBm output power 3) 11 mA