User`s manual

ManualsBrandsDynamix ManualsComputer equipmentDW-01

DYNAMIX DW-01Plus/S

FXS Gateway

User’s Manual

Summary of content (100 pages)

PAGE 1
DYNAMIX DW-01Plus/S FXS Gateway User’s Manual
PAGE 2
Part I: Dynamix DW-01Plus/SOverview .............................................................................1 1.1 Overview........................................................................................................................2 1.2 Software Specifications .............................................................................................3 1.3 Hardware Specifications ............................................................................................4 Part II: Start-UP.
PAGE 3
.3.2 Call Transfer – press [FLASH], then [transferring number] .............................. 33 3.3.3 Call Forward:......................................................................................................... 33 3.4 Upgrade Your Dynamix DW-01Plus/S .................................................................... 35 3.4.1 Upgrade via Web management interface........................................................... 35 3.4.1.1 Before start....................................................
PAGE 4
Part V: Telnet Command Interface.................................................................................... 63 5.1 Login ............................................................................................................................ 64 5.2 Save and Reboot........................................................................................................ 64 5.3 System Commands Overview ................................................................................. 65 5.3.
PAGE 5
Dynamix DW-01Plus/S Gateway User Manual Part I: Dynamix DW-01Plus/S Gateway Overview This part introduces the software/hardware specifications and default settings of the Dynamix DW-01Plus/S.
PAGE 6
Dynamix DW-01Plus/S Gateway User Manual 1.1 Overview The Dynamix DW-01Plus/S is a one-port telephone extension and three ports SOHO Router to IP network gateway. It provides Data transfer by 10/100Mbps, telephone services and T.38 fax over IP network with easily operation and configuration. It is most suitable for SOHO and small-to-medium enterprise in Internet communication environment. The Dynamix DW-01Plus/S provides IP telephone number for end users with FreeTalk voice service.
PAGE 7
Dynamix DW-01Plus/S Gateway User Manual 1.2 Software Specifications  Dynamix DW-01Plus/S Gateway Features               Provide Voice over IP and Fax over IP features. SIP RFC 3261 compliance Built-in NAT/IP sharing function Provided call features: Hold, forward and transfer Automatic FAX detection (Support T.38 protocol)  Codec: G.711 a/ìlaw, G.723.1, G.729A PPPoE connection VAD (Voice Activity Detection), CNG (Comfort Noise Generate) G.
PAGE 8
Dynamix DW-01Plus/S Gateway User Manual 1.3 Hardware Specifications     Chassis   190mm(W) x 110mm(D) x 51.5mm(H) Weight (unit): 0.3 kg    Four 10/100 Base-T Ethernet RJ-45 ports (Auto LAN MDI/MDIX). Input AC 100V-240V, Output DC 12V. One/Two RJ11 Telephone Port.
PAGE 9
Dynamix DW-01Plus/S Gateway User Manual (3) Light Blanking: Dynamix DW-01Plus/S is under Proxy mode and not successfully register to Proxy.  TEL (Orange): (1) Light Blinking: Dynamix DW-01Plus/S IP side has incoming call. (2) Light On: Dynamix DW-01Plus/S IP side is in communication. (3) Light Off: IP Line of Dynamix DW-01Plus/S is in standby mode.  WAN/LAN (Green): (1) Light on: Ethernet port successfully connected with network. (2) Light Blanking: Ethernet port is transmitting or receiving data.
PAGE 10
Dynamix DW-01Plus/S Gateway User Manual   TEL Port: RJ-11 connector, Dynamix DW-01Plus/S interface to connect analog phone sets or trunk port of PABX. PSTN Port: RJ-11 connector, Dynamix DW-01Plus/S interface to CO PSTN line or extension port of PABX.  DC 12V Port: DC 12V Power supply.
PAGE 11
Dynamix DW-01Plus/S Gateway User Manual : Part II: Start-UP This part explains how to configure essential and basic items before user can run Dynamix DW-01Plus/S gateway.
PAGE 12
Dynamix DW-01Plus/S Gateway User Manual 2.1 Software Installation Guide This guide covers all essential configurations under different application, user can follow steps below to configure basic items to run Dynamix DW-01Plus/S gateway. 2.1.1 Default Settings of Dynamix DW-01Plus/S gateway  WAN IP Parameters (1)    (2)    WAN IP Address = 10.1.1.3 Subnet mask = 255.0.0.0 Default gateway = 10.1.1.254 LAN IP Address = 192.168.123.123 Subnet mask = 255.255.255.
PAGE 13
Dynamix DW-01Plus/S Gateway User Manual the Ethernet port of your network (e.g. Cable Modem, ADSL Modem) using the standard CAT-5 straight Ethernet cable. Step 2. Connect your PC to the LAN port of Dynamix DW-01Plus/S Connect your PC to the LAN port of Dynamix DW-01Plus/S with standard CAT-5 straight Ethernet cable. Step 3. Set your PC as DHCP mode Please go to the network setting of your PC and set it as DHCP mode, let your PC can automatically search for DHCP server and get one valid IP address.
PAGE 14
Dynamix DW-01Plus/S Gateway User Manual 2.1.3.1 Save Data and Reboot After any configuration has been made, user has to save all data and reboot system to make configurations take effect. Step 1. Click [Commit Data] on the navigation panel. In the Commit Configuration Data screen, click the [Commit] button. In the Commit Configuration Data screen will Display [Commit to Flash OK!], when Dynamix DW-01Plus/S finished committing data. Step 2. Click [Reboot System] on the navigation panel.
PAGE 15
Dynamix DW-01Plus/S Gateway User Manual Step 3. Close the current browser windows and launch your web browser again.
PAGE 16
Dynamix DW-01Plus/S Gateway User Manual 2.1.3.2 Setup Network (1) Fixed IP To configure the VoIP Gateway IP address, please click [Network Interface] on the navigation panel. In the Network Interface screen, type a new IP address, subnet mask and the default routing gateway (e.g. IP Address: 192.168.0.188, Subnet mask: 255.255.255.0, Default routing gateway: 192.168.0.1) and click the OK button.
PAGE 17
Dynamix DW-01Plus/S Gateway User Manual (2) DHCP Click [Network Interface] on the navigation panel. In the Network Interface screen, enable the DHCP function if you are using the cable modem or DHCP server and click the [OK] button.
PAGE 18
Dynamix DW-01Plus/S Gateway User Manual (3) PPPoE Click [PPPoE Configuration] in the navigation panel and open the [PPPoE Configuration] Screen. - - Device: Set PPPoe function to be On or Off. User Name: Set PPPoE authentication User Name. Password: Set PPPoE authentication password.
PAGE 19
Dynamix DW-01Plus/S Gateway User Manual 2.1.3.3 Application mode-Proxy/Peer-to-Peer Mode After setting IP address, user must assign Dynamix DW-01Plus/S to work under Proxy mode or Peer-to-Peer mode. If there is no Gatekeeper, please set your Dynamix DW-01Plus/S as Peer-to-Peer Mode. 2.1.3.3.1 Proxy mode Proxy mode means that there will be an intermediate Proxy Server between Dynamix DW-01Plus/S Gateway and the remote entity.
PAGE 20
Dynamix DW-01Plus/S Gateway User Manual 2.1.3.3.2 Peer-to-Peer Mode Peer-to-Peer Mode allows users to call other VoIP devices without the proxy server. When in Peer-To-Peer mode, Dynamix DW-01Plus/S Gateway use Phone Book, which will dial predefined phone number, and press “#” (optional, to accelerate the dial) as end of dial. To configure Peer-To-Peer Mode in Dynamix DW-01Plus/S Gateway, follow the steps below: Step 1. Configure the Dynamix DW-01Plus/S Gateway SIP information.
PAGE 21
Dynamix DW-01Plus/S Gateway User Manual Step 2. Configure Phone Book in the Dynamix DW-01Plus/S Gateway. Click [Phone Book] on the navigation panel. In the Phone Book screen, enter the Index, Name, IP address and e164 (phone number) of the destination and click the Add Data button.
PAGE 22
Dynamix DW-01Plus/S Gateway User Manual 2.1.4 Essential Configuration via Telnet Command Line interface This section describes how to setup Dynamix DW-01Plus/S via Telnet command line interface. Please follow procedures below to configure essential items before you use Dynamix DW-01Plus/S gateway. 2.1.4.1 Save Data and Reboot After any configuration has been made, user has to save all data and reboot system to make configurations take effect. Step 1.
PAGE 23
Dynamix DW-01Plus/S Gateway User Manual For example: usr/config$ pppoe -print PPPoE adapter information Device : Enabled Status User name Password Reboot : Not initialized : 84460791@hinet.net : ******** : Yes usr/config$ Step 4. Commit and reboot Dynamix DW-01Plus/S. usr/config$ commit usr/config$ reboot Step 5. When Dynamix DW-01Plus/S successfully establish PPPoE connection, use command [pppoe -print] to see detail information.
PAGE 24
Dynamix DW-01Plus/S Gateway User Manual 2.1.4.3 Application mode-Proxy/Peer-to-Peer Mode After setting IP address, user must assign Dynamix DW-01Plus/S to work under Proxy mode or Peer-to-Peer mode. If there is no Proxy, please set your Dynamix DW-01Plus/S as Peer-to-Peer Mode. 2.1.4.3.1 Proxy mode Proxy mode means that there will be an intermediate Proxy Server between Dynamix DW-01Plus/S Gateway and the remote entity.
PAGE 25
Dynamix DW-01Plus/S Gateway User Manual Note: 1. Please contact with your Proxy vendor to obtain user account information. 2. If no need to enter password, user also has to set security information, please set “name” the same with line number. 2.1.4.3.2 Peer-to-Peer Mode Peer-to-Peer Mode allows users to call other VoIP devices without the proxy server.
PAGE 26
Dynamix DW-01Plus/S Gateway User Manual 2.1.5 Essential Configuration via Installation Wizard Installation Wizard is a friendly software tool that can provide you an easy way to configure your Dynamix VoIP devices. You only need to Input the MAC address of your product and Click [Search Device]; you can configure your VoIP device without changing your PC’s setting. Additionally, when you forget IP address of the VoIP device, Installation Wizard gives you a solution to solve this problem.
PAGE 27
Dynamix DW-01Plus/S Gateway User Manual 2.1 Special Housing Installation Guide Dynamix DW-01Plus/S has special adjustable housing for vertical or horizontal type. Please follow procedures as below to change type you like. 2.1.1 Horizontal Type 2.1.1.1 Insert stand board on one side. 2.1.1.2 Insert the other stand board on the other side. 2.1.1.3 Finally Dynamix DW-01Plus/S can stand as horizontal type.
PAGE 28
Dynamix DW-01Plus/S Gateway User Manual 2.1.2 Vertical Type 2.1.2.1 Insert stand board on one side. 2.1.2.2 Insert the other stand board on the same side. 2.1.2.3 Finally Dynamix DW-01Plus/S can stand as vertical type.
PAGE 29
Dynamix DW-01Plus/S Gateway User Manual : Part III: Special Features Applications and This part explains how to configure Dynamix DW-01Plus/S Gateway under special application mode, such as behind NAT, and how to upgrade firmware.
PAGE 30
Dynamix DW-01Plus/S Gateway User Manual 3.1 Behind IP-Sharing 3.1.1 IP Sharing Configuration 3.1.1.1 One Dynamix DW-01Plus/S Gateway This application is only for the user who is using the IP Sharing device. It is said Gateway is connected behind IP Sharing. The IP Sharing Device must support the DMZ or Virtual server functions such as ADSL network. Step 1. The WAN IP Address obtained from ADSL has two kinds of methods. One is fixed IP Address, while user applies for one or more fixed IP Addresses.
PAGE 31
Dynamix DW-01Plus/S Gateway User Manual Please see following for example: >Advanced setting > NAT setting > DMZ Host setting DMZ Host setting ▣ Activate DMZ DMZ Host IP: 192.168.1.5 Step 6. Configure the Dynamix DW-01Plus/S Gateway IP address for IP Sharing Mode. Click [Network Interface] on the navigation panel. In the Network Interface screen, enter the IP address, Subnet mask and the default gateway in the network table. Please follow up your IP Sharing device Step 7.
PAGE 32
Dynamix DW-01Plus/S Gateway User Manual Step 9. Click [Reboot System] on the navigation panel. In the VoIP Gateway screen, click the [Reboot] button. It will take around 40 seconds to reboot. Step 10. Close the current browser windows and launch your web browser again. Enter the new IP address in the Location or Address field.
PAGE 33
Dynamix DW-01Plus/S Gateway User Manual 3.1.1.2 More than one Dynamix DW-01Plus/S behind the same IP Sharing Device 1. 2. Assign an IP address to each Dynamix DW-01Plus/S using fixed address. Enable the IP Sharing function for each set using following command. Fixed IP Address – usr/config$ ifaddr –ipsharing 1 “public IP of IP Sharing” 3. Configure separate SIP port and RTP port for each set to prevent from port conflict.
PAGE 34
Dynamix DW-01Plus/S Gateway User Manual Note: With Dynamic WAN IP Address, when the WAN IP is changed, we need to change the external IP of Dynamix DW-01Plus/S Gateway using above command. 1. Different Vendor’s Router will have different appearance of setting. 2. Once you set the DMZ Host, you don’t need to configure the Port Forwarding and vice versa. 3.
PAGE 35
Dynamix DW-01Plus/S Gateway User Manual 3.2 NAT mode (PPPoE) Step 1. Set PPPoE mode, using [pppoe –dve 1], input the user id & password provided by your ISP, using [pppoe –id –pwd], reboot the device after disconnection, using [pppoe –reboot 1] usr/config$ pppoe –dve 1 (PPPoE used) usr/config$ pppoe –open (PPPoE open) usr/config$ pppoe –id 123@hinet.net (PPPoE login account) usr/config$ pppoe –pwd 123 (PPPoE login Passowd) usr/config$ pppoe –reboot 1 (Enable) Step 2.
PAGE 36
Dynamix DW-01Plus/S Gateway User Manual Step 3. When Gateway connection succeed. Setup PC use LAN IP connection Network Select [Specify an IP Address] and enter [192.168.123.xxx] in the [IP Address] location (where xxx is a number between 2 and 254 used by the VoIP Gateway to identify each computer), and the default [Subnet Mask 255.255.255.0]. Please notice that two computers on the same LAN cannot have the same IP address. Set Default Gateway value as 192.168.123.123 in the [new gateway] field.
PAGE 37
Dynamix DW-01Plus/S Gateway User Manual 3.3 Call Hold, Transfer and Forward Gateway provides call features including call hold, transfer and forward. Please be noted that both calling and called site have to support this feature. For call forward function, it only works under Proxy mode. Of course, Proxy must support these call features, too. It is better for user to prepare a telephone set supported [FLASH] function on keypad.
PAGE 38
Dynamix DW-01Plus/S Gateway User Manual 3.3.3.2 Busy Forward: While line is engaged or phone set is been off-hook, incoming call will be forwarded to the assigned number. (1) Activate: *76 [Forward No.] # (2) Deactivate: #76# 3.3.3.3 Unconditional: Incoming call will be forwarded to the assigned number unconditionally. (1) Activate: *77 [Forward No.
PAGE 39
Dynamix DW-01Plus/S Gateway User Manual 3.4 Upgrade Your Dynamix DW-01Plus/S . 3.4.1 Upgrade via Web management interface 3.4.1.1 Before start Step 1. Please confirm Host PC, which is installed as TFTP / FTP server and is in available network. Step 2. Note down your current configurations, such as [SIP Information], [Phone Book]. 3.4.1.2 Upgrade Version Step 1. To update the Dynamix DW-01Plus/S Gateway ROM Version, please click [ROM Upgrade] on the navigation panel.
PAGE 40
Dynamix DW-01Plus/S Gateway User Manual Step 2. After upgrade finished, on screen will display [Please issue FLASH CLEAN to consist software version.] information. Step 3. Click [Flash Clean] on the navigation panel. In the Flash Clean screen, click the [CLEAN] button. Step 4. In the Flash Clean screen to Display [Flash cleaned!! Please reboot your system!!], when Flash Clean Ok.
PAGE 41
Dynamix DW-01Plus/S Gateway User Manual Step 5. Click [Reboot System] on the navigation panel. In the Reboot Dynamix DW-01Plus/S Gateway screen, click the [Reboot] button. It will take 40 seconds to reboot. Step 6. Close the current browser windows and launch your web browser again. Enter the IP address in the Location or Address field. 3.4.2 Upgrade via Telnet Command interface Use [rom] command to upgrade software of Dynamix DW-01Plus/S.
PAGE 42
Dynamix DW-01Plus/S Gateway User Manual Parameter Usages: -print: show versions of all rom files. -app, boot, boot2m, dsptest, dspcore, dspapp, ht: To update main Application program code, Boot code, DSP testing code, DSP kernel code, or DSP application code, and Hold Tone file. Note: Most of all, the Rom file needed to get upgrade is App or Boot2m. Please check the exact Rom file before doing download procedure. -s: To specify TFTP server’s IP address when upgrading ROM files.
PAGE 43
Dynamix DW-01Plus/S Gateway User Manual 3.5 Dynamix DW-01Plus/S PSTN Line Application 3.5.1 PSTN Outgoing Call 3.5.1.1 Make PSTN call from TEL Phone set Default TEL line is intended to make IP call, if user wants to make a call via PSTN line, please dial “*#”, then user will hear dial tone from PSTN side. The dial tone between IP side and PSTN are different. If the PSTN port doesn't connect a PSTN line, press “*#”, the signal will be back to IP side then play busy tone. 3.5.1.
PAGE 44
Dynamix DW-01Plus/S Gateway User Manual 3.6 Hotline mode The Hotline Mode is applied in limited two peers. User just picks up the phone set and then hears ring back tone or dial tone depended on configurations of destination device. Step 1. Specify gateway service type as Hotline service. Step 2. Create a Hotline table with [line] command. usr/config$ sysconf –service 1 usr/config$ bureau –hotline 1 10.2.2.
PAGE 45
Dynamix DW-01Plus/S Gateway User Manual Part IV: Web Management Interface This part explains how to configure the Dynamix DW-01Plus/S Gateway via WEB management interface.
PAGE 46
Dynamix DW-01Plus/S Gateway User Manual 4.1 Login and welcome screen Step 1. Start your web browser. Step 2. Launch your web browser and enter [192.168.123.123] (the default IP address of the LAN port) in the Location or Address field. Press Enter. Step 3. Password request screen will appear as below. Please input “root” in the user name field and no password in the password field. Step 4. Click OK. Step 5. After a successful login, you will see the welcome screen described next.
PAGE 47
Dynamix DW-01Plus/S Gateway User Manual 4.2 Save and Reboot Click OK at the end of every configuration page to confirm your changes. All configurations will not take effect before reboot system. Please remember to do [Commit Data] to save all configuration then [Reboot System] to reboot Dynamix DW-01Plus/S.
PAGE 48
Dynamix DW-01Plus/S Gateway User Manual 4.3 Web Management Configuration 4.3.1 Network Interface Click [Network Interface] in the navigation panel and open the Network Interface Screen. - - LAN IP Address: Set LAN IP Address of Dynamix DW-01Plus/S (range: 192.168.1.1- 192.168.254.
PAGE 49
- - - Dynamix DW-01Plus/S Gateway User Manual IP Sharing: Enable it if Dynamix DW-01Plus/S is behind IP Sharing router. UPnP: Enable it if IP sharing or NAT device supports UPnP function so that no need to configure IP sharing or Dynamix DW-01Plus/S when Dynamix DW-01Plus/S is behind NAT device. IP Sharing Server Address: Set Public IP Address of IP Sharing router for Dynamix DW-01Plus/S to work behind IP sharing. Primary DNS Server: Set Primary Domain Name Server IP address.
PAGE 50
4.3.2 SIP Information Screen Dynamix DW-01Plus/S Gateway User Manual Click [SIP Configuration] in the navigation panel and open the SIP Information Screen. - - - - Run Mode: Select Dynamix DW-01Plus/S to work under Peer-to-Peer mode or Proxy mode. Primary Proxy IP Address: Set primary Proxy IP Address or URL address (Domain Name Server must be configured. Please refer to Network Interface).
PAGE 51
- Dynamix DW-01Plus/S Gateway User Manual prefix as abc, Dynamix DW-01Plus/S will set out as abc123@”IP address of Proxy”. This function is for special proxy server. Line Number: identify one number for the Dynamix DW-01Plus/S to register to the Proxy. Line Account: set user name of Dynamix DW-01Plus/S for registering. User can - set user name and password for registering. If password is no need, please set user name the same as line number or Dynamix DW-01Plus/S won’t register successfully.
PAGE 52
4.3.3 System Configuration Dynamix DW-01Plus/S Gateway User Manual Click [System Configuration] in the navigation panel and open the [System Configuration] Screen. - - - - Keypad DTMF Type: set DTMF type. User can select DTMF type Dynamix DW-01Plus/S transmits. RFC2833 Payload Type: change RFC2833 Payload type. This is for special request from the other site, if RFC2833 payload types of 2 sites are different, it may cause some problem of connection.
PAGE 53
Dynamix DW-01Plus/S Gateway User Manual 4.3.4 PPPoE Configuration Screen Click [PPPoE Configuration] in the navigation panel and open the [PPPoE Configuration] Screen. - - Device: Set PPPoe function to be On or Off. User Name: Set PPPoE authentication User Name. Password: Set PPPoE authentication password.
PAGE 54
Dynamix DW-01Plus/S Gateway User Manual 4.3.5 Voice Configuration Screen Click [Voice Configuration] in the navigation panel and open the [Voice Configuration] Screen. - - Codec Priority: set codecs priority in order. Please notice that user can set from 1 to 5 codecs as their need. For example, user can only set first priority as G.723.1, and set the others as x, that means only G.723.1 is available. Frame Size: User can set different packet size for each codec. G.
PAGE 55
Dynamix DW-01Plus/S Gateway User Manual 4.3.6 Phone Configuration Screen Click [Phone Configuration] in the navigation panel and open the [Phone Configuration] Screen. For tone simulation, Dynamix DW-01Plus/S Gateway adopts dual frequencies as traditional telephone does. If users want to have their own call progress tone, they can change the value of tones. - Ring Tone: Set Ring frequency, on time, off time, voltage level. Dynamix DW-01Plus/S will give ring to phone set to trigger ring.
PAGE 56
      Dynamix DW-01Plus/S Gateway User Manual Low(lev) : Level (volume) of Low frequency High(lev) : Level (volume) of High frequency On1 : On cadence of first cycle Off1 : Off cadence of first cycle On2 : On cadence of second cycle Off2 : Off cadence of second cycle Note: 1. If disconnect tone is single-frequency, user has to configure the same frequency value of “Low frequency” and “High frequency”; the same level of “Low frequency” and “High frequency” 2.
PAGE 57
Dynamix DW-01Plus/S Gateway User Manual 4.3.7 Support Configuration Screen Click [Support configuration] in the navigation panel and open the [Support Configuration] Screen. - T.38 FAX: enable/disable FAX function. If user wants to fax with Dynamix DW-01Plus/S gateway, this function must be enabled.
PAGE 58
4.3.8 Phone Book Configuration Dynamix DW-01Plus/S Gateway User Manual Click [Phone Book Configuration] in the navigation panel and open the [Phone Book] Screen. - - Add Data: User can specify 10 sets of phone book via Web Management Interface. Please input index, Name, IP Address and E.164 number of the destination device. Delete Date: User can delete any configured phone book data by index. Note: The e164 number defined in phone book will be fully sent to destination.
PAGE 59
Dynamix DW-01Plus/S Gateway User Manual 4.3.9 Prefix Configuration Screen Click [Prefix configuration] in the navigation panel and open the [Prefix Drop/Insert Configuration] Screen. - - Index: Setting the index number for prefix record (max 30 record). Prefix: Setting the prefix number of the whole numbers that could be into this VoIP gateway (1~20 digits). Drop: Select enable or disable drop prefix function. The function is enabled means to drop prefix number when dialing out.
PAGE 60
Dynamix DW-01Plus/S Gateway User Manual 4.3.10 DSCP Configuration Screen Click DSCP Configuration in the navigation panel and open the DSCP Configuration Screen. Set Signal or RTP Packet DSCP value: - Assured Forwarding (AF) PHB: Select Delay priority and Drop Precedence - Expedited Forwarding (EF) PHB: Select TOS value as EF - Default: Select TOS value as 0 - User Assign Special DSCP Code: User can set other unspecified value here.
PAGE 61
Dynamix DW-01Plus/S Gateway User Manual DROP Precedence Class #1 Class #2 Class #3 Class #4 Low Drop Precedence (AF11) (AF21) (AF31) (AF41) 001010 010010 011010 100010 (AF12) (AF22) (AF32) (AF42) 001100 010100 011100 100100 (AF13) (AF23) (AF33) (AF43) 001110 010110 011110 100110 Medium Drop Precedence High Drop Precedence Please refer to RFC standard documents for more information about what is DSCP.
PAGE 62
Dynamix DW-01Plus/S Gateway User Manual 4.3.10 Password Configuration Screen Click [Password configuration] in the navigation panel to open the [Password Configuration] screen. It is highly recommended that you change the default password ([Null]). - - Change: First select login name as root or administrator, then enter current password, new password and confirm new password again to set new password. Abort: Press abort will clean all inputs.
PAGE 63
Dynamix DW-01Plus/S Gateway User Manual 4.3.11 ROM Configuration Screen Click [ROM Upgrade] in the navigation panel and open the [ROM Configuration] Screen.
PAGE 64
4.3.12 Flash Clean Screen Dynamix DW-01Plus/S Gateway User Manual Click [Flash Clean] in the navigation panel and open the [Flash Clean] Screen. - Press CLEAN will clean all configurations of Dynamix DW-01Plus/S and reset to factory default value.
PAGE 65
Dynamix DW-01Plus/S Gateway User Manual 4.3.13 Commit Configuration Data Screen Click [Commit Data] in the navigation panel and open the [Commit Configuration Data] Screen. - Commit Date to save all configurations. Please remember to commit data before reboot your Dynamix DW-01Plus/S.
PAGE 66
Dynamix DW-01Plus/S Gateway User Manual 4.3.14 Reboot Dynamix DW-01Plus/S System screen Click [Reboot System] in the navigation panel and open the [Reboot Dynamix DW-01Plus/S Gateway] Screen. - Press reboot will reset Dynamix DW-01Plus/S. Note: To execute reboot, please remember to do Commit Data before Reboot System.
PAGE 67
Dynamix DW-01Plus/S Gateway User Manual Part V: Telnet Command Interface This part gives information on how to configure Dynamix DW-01Plus/S gateway via Telnet command line interface.
PAGE 68
Dynamix DW-01Plus/S Gateway User Manual 5.1 Login For you first login, enter the login: [root] and default no password. login: root password: Welcome to Terminal Configuration Mode Please enter your configuration item usr/config$ Note: Login account [root] or [administrator] is the default login account and there is no password needed. 5.2 Save and Reboot After any configuration has been made, user has to save all data and reboot system to make configurations take effect. Step 1.
PAGE 69
Dynamix DW-01Plus/S Gateway User Manual 5.3 System Commands Overview 5.3.1 [help] Press help/man/ ? will display all command list of Dynamix DW-01Plus/S. The following table lists all of the commands that you can use with the Gateway. Refer to the following chapters for descriptions of commonly used commands. This user’s guide describes commands that are helpful for configuring the Gateway. Using commands not documented in the user’s guide can damage the unit and possibly render it unusable.
PAGE 70
Dynamix DW-01Plus/S Gateway User Manual Command DESCRIPTION prefix Prefix drop/insert information manipulation 5.3.2 [quit] Type [quit] will quit the Gateway configuration mode. And turn back to login prompt. usr/config$ quit Disconnecting.. login: root Welcome to Terminal Configuration Mode Please enter your configuration item usr/config$ Note: It is recommended that type the [quit] command before you leave the console. If so, Gateway will ask password again when next user connects to console port.
PAGE 71
Dynamix DW-01Plus/S Gateway User Manual Parameter Usages: -status: Display the enabled debug flags. -add: Add debug flag. -- sip: sip related information -- msg: voice related information -delete: Remove specified debug flag. -open: Start to show debug messages. -close: Stop showing debug messages. In this example, user open debug flags including sip, vp, msg.
PAGE 72
Dynamix DW-01Plus/S Gateway User Manual 5.3.4 [reboot] After [commit], type [reboot] to reload Gateway in new configuration. The procedure is as below: usr/config$ reboot Start to Unregister ... Unregister complete... . Rebooting...It will take 40 seconds....Attached TCP/IP interface to cpm unit 0 Attaching interface lo0...done HTTPD initialized... Flash Check WorkMode : PROXY_MODE Start registering to Proxy server AC4804[0] is ok AC4804[1] is ok successful 2 2 Initialize OSS libraries...OK! VP v1.
PAGE 73
Dynamix DW-01Plus/S Gateway User Manual 5.3.6 [ifaddr] Configure and display Gateway network information. usr/config$ ifaddr LAN information and configuration Usage: ifaddr [-print]|[-dhcp used]|[-sntp mode [server]] ifaddr [-ip ipaddress] [-mask subnetmask] [-gate defaultgateway] ifaddr [-dns index [dns server address]] [-ipsharing used[ip address]] ifaddr [-autodns used] -print Display LAN information and configuration. -ip Specify WAN ip address. -lanip Specify LAN ip address.
PAGE 74
Dynamix DW-01Plus/S Gateway User Manual ifaddr -autodns 1 ifaddr -dns 1 168.95.1.1 usr/config$ Parameter Usages: -print: Print current IP setting and status -ip: Assigned IP address for Gateway -lanip: Specify LAN port IP address (For NAT function), use this command setup LAN IP address assigned to PC or other machine. usr/config$ ifaddr -lanip 192.168.XXX.
PAGE 75
Dynamix DW-01Plus/S Gateway User Manual -server: set EMS server IP address. EMS is software to help user can easily configure products. Please contact with your reseller for more information. -id: specify EMS ID to login EMS Server. -pwd: specify EMS password to login EMS Server. -emstime: specify EMS cycle time. For example: usr/config$ ifaddr -print Internet address information WAN IP address : 192.168.13.71 Subnet mask : 255.255.248.0 Default gateway : 192.168.8.
PAGE 76
Dynamix DW-01Plus/S Gateway User Manual 5.3.8 [ping] Use [ping] to test whether a specific IP is reachable or not. For example: if 192.168.1.2 is not existing while 210.63.15.32 exists. Users will have the following results: usr/config$ ping 192.168.1.2 no answer from 192.168.1.2 usr/config$ ping192.168.1.254 PING 192.168.1.254: 56 data bytes 64 bytes from 192.168.1.254: icmp_seq=0. time=5. ms 64 bytes from 192.168.1.254: icmp_seq=1. time=0. ms 64 bytes from 192.168.1.254: icmp_seq=2. time=0.
PAGE 77
-print -add -search -delete Dynamix DW-01Plus/S Gateway User Manual Display phonebook data. Add an record to phonebook. Search an record in phonebook. Delete an record from phonebook. -insert Insert an record to phonebook in specified position. -modify Modify an exist record. Note: If parameter 'end_record' is omited, only record 'start_record' will be disp lay. If both parameters 'end_record' and 'start_record' are omited, all records will be display. Range of ip address setting (0.0.0.0 ~ 255.255.255.
PAGE 78
Dynamix DW-01Plus/S Gateway User Manual --port: Call signal port number of caller --drop : Drop e.164 number when dial out. 0 means to keep e.164 number, 1 means to drop e.164 number when dialing out. --inert: Insert digits.(1~10 digits) usr/config$ pbook –add name test e164 100 ip 192.168.13.78 -modify: modify an existing record. When using this command, users have to specify the record’s index number, and then make the change. usr/config$ pbook –modify 1 name test e164 5678 ip 192.168.1.
PAGE 79
-open -close -id -pwd Dynamix DW-01Plus/S Gateway User Manual Open PPPoE connection. Disconnect PPPoE connection. Connection user name. Connection password. -reboot Reboot after remote host disconnection. -echo PPPoE Echo Request (0=disable, 1=enable). usr/config$ Parameter Usages: -print: print PPPoE status.
PAGE 80
Dynamix DW-01Plus/S Gateway User Manual Note: This command will clean the configuration stored in the flash and reboot it. usr/config$ Parameter Usages: -clean: clean all the user defined value, and reboot Gateway in factory default mode. Note: 1. It is recommended to execute [flash –clean] after application firmware been upgraded. 2. Only User who login with root can execute it. After flash clean, all configurations in command [ifaddr] and [pppoe] will still be kept.
PAGE 81
5.3.12 [sysconf] Dynamix DW-01Plus/S Gateway User Manual This command displays system information and configurations. usr/config$ sysconf System information and configuration Usage: sysconf [-print] [-idtime digit] [-bf digit] [-keypad dtmf] [-faxtype type][-2833type type][-lcdrop ON/OFF] [-droptime digit][-eod digit] [-callerid type] [-service used][-dtmfstart digits] [-dtmfend digits] sysconf -print -print -idtime -service Display system overall information and configuration. Inter-Digits time.
PAGE 82
Dynamix DW-01Plus/S Gateway User Manual If after the duration user hasn’t pressed next number, it will dial out all number pressed (1-10 seconds). -service: set SIP Phone to be normal mode or under hotline mode. (sysconf –service 0/1, 0 for normal service, 1 for hotline service.) -keypad: DTMF replay type. When value is “1”, Dynamix DW-01Plus/S Gateway will transfer DTMF signal via RTP payload as defined in RFC2833. When the value is set to “0”, the DTMF type is set as In-band, and 2 for SIP info DTMF.
PAGE 83
5.3.13 [sip] Dynamix DW-01Plus/S Gateway User Manual This command is to configure SIP related parameters. usr/config$ sip SIP stack information and configuration Usage: sip [-print] [-mode pxmode] [-outpx IPaddmress] [-transport type] sip [-px address] [-px2 address] [-pxport number] [-outpxport number] [-line1 number] [-prefix prefixstring] [-expire t1] [-port udpPort] [-rtp rtpPort] sip -print -print Display SIP stack information and configuration. -mode Configure as Peer-to-Peer mode:0/Proxy mode:1.
PAGE 84
Dynamix DW-01Plus/S Gateway User Manual -pxport: Set Proxy port for Dynamix DW-01Plus/S to send message, default value is 5060, if there is no special request of Proxy server, please don’t change this value. -outpx: Set IP Address or URL address (Domain Name Server must be configured. Please refer to Network Configure) of outbound Proxy server.
PAGE 85
Dynamix DW-01Plus/S Gateway User Manual Proxy port : 5060 OutBound Proxy address : null Transport Type (TCP/UDP) : UDP Prefix string : null Line1 Line2 Line3 Line4 : 1001 : 1002 : 1003 : 1004 pbook search : OFF SIP listen port RTP receive port Expire usr/config$ : 5060 : 16384 : 3600 5.3.
PAGE 86
Dynamix DW-01Plus/S Gateway User Manual -name: Specify the username of your account information. -pwd: Specify the password of your account information. For example: usr/config$ security -print Line1 account information Username : 1001 Password : *** usr/config$ 5.3.15 [voice] The voice command is associated with the audio setting information. There are four voice codecs supported by Gateway.
PAGE 87
Dynamix DW-01Plus/S Gateway User Manual dtmf volume (0~31, default: 23), -nscng No sound compression and CNG. (G.723.1 only, On=1, Off=0). -echo Setting of echo canceller. (On=1, Off=0, per port basis). -mindelay Setting of jitter buffer min delay. (0~150, default: 90). -maxdelay Setting of jitter buffer max delay. (0~150, default: 150).
PAGE 88
Dynamix DW-01Plus/S Gateway User Manual Note: Be sure to know well the application before you change voice parameters because this might cause incompatibility. For example: usr/config$ voice -print Voice codec setting relate information Sending packet size : G.729A : 40 ms G.723.1 : 60 ms G.711U : 40 ms G.711A : 40 ms Priority order codec : g729a g7231 g711u g711a Volume levels : voice volume : 25 input gain : 25 dtmf volume : 23 No sound compress & CNG : G.729A : There is no setting G.723.1 : Off G.
PAGE 89
Dynamix DW-01Plus/S Gateway User Manual support -print -t38 T.38(FAX) enabled/disabled. -busy Busy Forward number.(if empty, please fill "null") -noanswer No Anser Forward number.(if empty, please fill "null") -uncon Unconditional Forward number.(if empty, please fill "null") Example: support -t38 1 support -busy 1001 support -uncon null usr/config$ Parameter Usages: -print: print current settings in support command. -t38: Enable or disable T.38 fax ability.
PAGE 90
5.3.17 [tos] Dynamix DW-01Plus/S Gateway User Manual This command is for setting Differentiated Service Code Point configuration. usr/config$ tos IP Packet ToS(type of Service)/Differentiated Service configuration Usage: tos [-rtptype dscp] tos [-sigtype dscp] tos -print [-rtpreliab mode] tos -print Example: tos -rtptype 7 -sigtype 0 usr/config$ Parameter Usages: -rtptype: the packages of voice (0~63). -sigtype: the package of call signal (0~63). Note: The value of rtptype and sigtype is from 0 to 63.
PAGE 91
Dynamix DW-01Plus/S Gateway User Manual tone specification or users-defined tone specification.
PAGE 92
Dynamix DW-01Plus/S Gateway User Manual phone -print rbt phone -ring 20 2000 4000 94 phone -rbt 480 440 125 105 2000 4000 2000 4000 phone -bt 620 480 125 105 500 500 500 500 phone -dt 440 350 96 96 8000 0 8000 0 phone -flash 400 800 phone -level 1 32 usr/config$ Parameter Usages: -print: Print current call progress tone configurations (ring: ring tone, rbt: ring back tone, bt: busy tone, dt: dial tone). This parameter should be accompanied with tone type. -ring: To set RING tone value.
PAGE 93
Dynamix DW-01Plus/S Gateway User Manual Ringback Tone tone2 off : 4000 usr/config$ usr/config$ phone -print rbt Phone ring back tone paramter Ringback Tone frequency high : 440 Ringback Tone frequency low : 480 Ringback Tone frequency high level : 13 Ringback Tone frequency low level Ringback Tone tone1 on Ringback Tone tone1 off Ringback Tone tone2 on Ringback Tone tone2 off : 13 : 100 : 200 : 100 : 200 usr/config$ usr/config$ phone -print bt Phone busy tone paramter Busy Tone frequency high : 620 Busy
PAGE 94
Dynamix DW-01Plus/S Gateway User Manual Dial Tone frequency low level Dial Tone tone1 on Dial Tone tone1 off Dial Tone tone2 on Dial Tone tone2 off usr/config$ usr/config$ : 155 : 8000 :0 : 8000 :0 usr/config$ phone -print flash Phone flash paramter Flash frequency high : 800 Flash frequency low : 400 usr/config$ 5.3.19 [bureau] To set Hotline function.
PAGE 95
Dynamix DW-01Plus/S Gateway User Manual -hotline: Define Line1 Hotline table respectively. The table is included [Line number], [destination IP Address] and [destination Port or Number]. For example 1. Destination is a FXS device, 628 is its Line1 number usr/config$ bureau -hotline 1 200.168.4.69 628 User picks up the Line1, and then hears the ring back tone generated from destination. Of course, 628 are ringing simultaneously.
PAGE 96
-dspapp -s -f -method Dynamix DW-01Plus/S Gateway User Manual update DSP application code(optional) IP address of TFTP/FTP server (mandatory) file name(mandatory) download via TFTP/FTP (TFTP: mode=0, FTP: mode=1) -ftp specify username and password for FTP -server specify EMS Server IP address Note: This command can run select one option in 'app', 'boot', , 'dsptest', 'dspcore', and 'dspapp'. Example: rom -method 1 rom -ftp vwusr vwusr rom -app -s 192.168.4.101 -f app.
PAGE 97
Dynamix DW-01Plus/S Gateway User Manual Application Rom DSP App DSP Kernel DSP Test Code : 1asip.107 : 48302ce3.140 : 48302ck.140 : 483cbit.bin Hold Tone : holdtone.101 usr/config$ 5.3.21 [auth] For security concern, the “root” user can customize some configurable items for “administrator” user. usr/config$ auth Root control what command administrator can use. Usage: auth -print Display auth switch configuration. Use item name to do config name (0=Disable, 1=Enabled).
PAGE 98
Dynamix DW-01Plus/S Gateway User Manual sysconf : Disable voice : Disable phone : Disable rtp : Disable tos : Disable prefix : Disable passwd : Enable rom : Disable flash bureau pppoe : Disable : Enable : Enable usr/config$ 5.3.22 [passwd] For security concern, users have to input the password before entering configuration mode. [passwd] command is for password setting purpose.
PAGE 99
Note: Dynamix DW-01Plus/S Gateway User Manual Gateway Login name only use [root] or [administrator]. [root] and [administrator] have the same authorization, except commands that can be excuted by [Login name: root] only [passwd –set root], [rom –boot], [room-boot2m] and [flash –clean]. For example: usr/config$ passwd -set root root1234 Setting login: root Password: root1234 OK usr/config$ sr/config$ passwd -clean Please wait a moment!! Clean password OK. usr/config$ 5.3.
PAGE 100
Dynamix DW-01Plus/S Gateway User Manual prefix -delete 1 prefix -modify 1 prefix 100 drop 0 insert 300 usr/config$ Parameter Usages: -add: Add a rule to drop or insert prefix digits of incoming call. --prefix: Set which prefix number to implement prefix rule. --drop: Enable or disable drop function. If this function is enabled, Gateway will drop prefix number on incoming call. --insert: Set which digit to insert on incoming call.