Dynamix DW Phone LP - 201 VoIP Phone (SIP) User Manual
Dynamix DW-Phone LP-201 SIP IP Phone Chapter 1 Overview of the Dynamix DW-Phone LP-201 ...................................................... 4 1. Hardware Overview .................................................................................................. 5 1.Front View and Keypad function ......................................................................... 5 2.Back View........................................................................................................... 9 3.
Dynamix DW-Phone LP-201 SIP IP Phone 11. [flash] command.................................................................................................... 47 12. [sysconf] command ............................................................................................... 48 13. [sip] command ...................................................................................................... 49 14. [security] command.....................................................................................
Dynamix DW-Phone LP-201 SIP IP Phone Chapter 1 Overview of the Dynamix DW-Phone LP-201 SIP-Phone Dynamix DW-Phone LP-201 is a full-featured IP-based telephone set via Ethernet base communication. Over the office LAN connection, it provides IP-PBX solution such as station-to-station call, IP call and local PSTN/PBX Extension call via PSTN Gateway. Dynamix DW-Phone LP-201 provides two 10/100BaseT switch/hub RJ-45 ports allow connecting to office LAN and PC simultaneously.
Dynamix DW-Phone LP-201 SIP IP Phone 1. Hardware Overview 1.Front View and Keypad function ♦ ♦ ♦ ♦ ♦ ♦ LCD: 2 lines, 24 character Dot Matrix display. C: Jump out current LCD menu. : Move to previous selection or clear previous data. : Move to right or next selection. OK: Press OK to confirm the modification. Direct Line (DL) Button 1 – 10: User press DL button after off-hook to do speed dial according to phone book data from 1-10 (please refer to LCD configuration-3.
Dynamix DW-Phone LP-201 SIP IP Phone ♦ Number 1 –10, * and #: The function is the same as the general phone set. Corresponding list of keypad and symbol: (1) Character mode: 1 “1” 2 “A” ; “ B” ; “C” ; “2” 3 “D” ; “E” ; “F” ; “3” 4 “G” ; “H” ; “I” ; “4” 5 “J” ; “K” ; “L” ; “5” 6 “M” ; “N” ; “O” ; “6” 7 “P” ; “Q” ; “R” ; “S” ; “7” 8 “T” ; “U” ; “V” ; “8” 9 “W” ; “X” ; “Y” ; “Z” ; “9” * “.
Dynamix DW-Phone LP-201 SIP IP Phone Note: 1. When Dynamix DW-Phone LP-201 is in PSTN mode, only PSTN and SPEAKER function key can work. 2. On LCD will display ”…Incoming Call... ” to inform user when Dynamix DW-Phone LP-201 has both IP and PSTN side incoming calls. 3. If in communication with IP side, user can press HOLD to hold IP side, then press PSTN to pick up PSTN side, after that can press HOLD again to retrieve IP side. 4.
Dynamix DW-Phone LP-201 SIP IP Phone 2. Change characters to be capital or lowercase: when pressing TRANSFER before press letters can switch input type of letters. ♦ ♦ ♦ REDIAL: Redial the last outgoing call. + And -: Adjust the voice volume heard of communication. SPEAKER: Hand free mode. User can talk without picking up handset. Note: 1. All function keys mentioned above (except dialing keypad) are effective only in IP Phone mode. 2.
Dynamix DW-Phone LP-201 SIP IP Phone 2.Back View ♦ ♦ DC 9V: DC 9V power input outlet LAN: RJ-45 connector, connected directly to the Hub through the straight CAT-5 cable. ♦ PC: RJ-45 connector, connected directly to the PC through the straight CAT-5 cable ♦ Line: RJ-11 connector, connected directly to the PSTN analog line. Note: There are two LED indicated lights: LINK/ACT and 10/100 for LAN port and PC port.
Dynamix DW-Phone LP-201 SIP IP Phone 2 RJ-11connector: RJ-11 connector is for connecting Dynamix DW-Phone LP-201 with PSTN.
Dynamix DW-Phone LP-201 SIP IP Phone 2.
Dynamix DW-Phone LP-201 SIP IP Phone Provisioning and Configuration SIP (RFC3261) compliance LCD configuration password protection Provide Proxy Mode or Peer-to-Peer Mode (Non Proxy Server needed) selection Ring tone, Speaker and Handset volume adjustable Dial path selection (PSTN or IP mode) Support DNS server inquiry Management Features: Software Upgrade: TFTP/FTP download Three easy ways for system configuration - LCD Front Panel - Web Browser - TELNET Certification CE, 3C 12 User Manual
Dynamix DW-Phone LP-201 SIP IP Phone 3.
Dynamix DW-Phone LP-201 SIP IP Phone Chapter 2 Configuring the Dynamix DW-Phone LP-201 through LCD Phone menus Note: 1. After any configuration is made for the SIP-Phone, user has to do Reboot in the selection 7 “Reboot”. 2. We suggest user to set IP address via LCD menu 5→ 2.3.4.5 first, then go to chapter 3 to do other detail configurations via web browser. 1. Initialize SIP-Phone 1. When power on the SIP-Phone, the LCD screen shows as below. Now Dynamix DWPhone LP-201 is running Boot sector program.
Dynamix DW-Phone LP-201 SIP IP Phone 5. After pressing the PSTN button, the “Proxy” or “P2P” will be replaced by “PSTN”. Please notice that user must plug PSTN line in RJ-11 port when Dynamix DWPhone LP-201 is in PSTN mode. SIP Phone will always stay in IP mode, after a PSTN call is finished, SIP Phone will automatically return to IP mode.. PSTN IP-Phone 10:10:10 AM 6. Press or to enter configuration mode then press OK button to enter sub menus; press C can jump out current menu to previous level. 1. 2.
Dynamix DW-Phone LP-201 SIP IP Phone 2. LCD Menu Configuration User can set the following configurations by LCD keypad. Note: 1. Press TRANSFER before input data can switch characters to be capital or lowercase. 2. Press SPEED before input data can switch input mode as character mode or digit mode; for example, user wants to enter IP address, after pressing SPEED can enter digits directly. 3. When user is inputting data, press C will jump out to menu list, press clear previous input data. will 1.
Dynamix DW-Phone LP-201 SIP IP Phone B. Deactivate Deactivate No Response Forward function. (3) Unconditional It is included the above two types. Whether the Dynamix DWPhone LP-201 is in which status, calls will be automatically forwarded to the assigned phone number. A. Activate Enter a forwarded phone number to activate Unconditional Forward function. B. Deactivate Deactivate Unconditional Forward function. 3. Phone Book 1.
Dynamix DW-Phone LP-201 SIP IP Phone 5. Network 1. Information User can press or to check current network status: (1) Mode: Display current network connection mode of Dynamix DWPhone LP-201 to be Static (Fixed IP), DHCP, or PPPoE. Note: When Dynamix DW-Phone LP-201 is under DHCP mode, then change to Static mode, the following items: IP address, Subnet Mask, Default Gateway, will display empty, after reboot, user can see information again. (2) IP, Mask, Gateway: display current IP information. 2.
Dynamix DW-Phone LP-201 SIP IP Phone 8. SNTP Configuration (1) SNTP Mode: User can set SNTP function to be on or off, which means Dynamix DWPhone LP-201 will capture current time from SNTP server or not. (2) SNTP Server: User can specify a SNTP server for Dynamix DW-Phone LP-201 to capture current time. (3) Time Zone: User can set time zone via pressing or according to the location Dynamix DW-Phone LP-201 is. For example, in Taiwan the time zone should be set as GMT+8:00. 9.
Dynamix DW-Phone LP-201 SIP IP Phone (2) Proxy A. Proxy Set Proxy IP address or Domain Name. B. Outbound proxy Set Outbound Proxy IP address or Domain Name. C. Proxy port Set Proxy port for Dynamix DW-Phone LP-201 to send messages. D. Expire (in seconds) Set expire time of registration, in the duration of 2/3 expire time, Dynamix DW-Phone LP-201 will re-register to Proxy Server again. (3) User Info A. User Name Set User Name of Dynamix DW-Phone LP-201 to register to Proxy Server.
Dynamix DW-Phone LP-201 SIP IP Phone (5) File Name User has to press the file name of new application rom file prepared for upgrading (6) Application Version Show current version of application. (7) Start to Upgrade Select YES or NO to start upgrade. Note: Download via LCD command can only upgrade new application rom file. 4. LCD Menu Password Set entry password of phone LCD menu. 7. Reboot Reboot machine.
Dynamix DW-Phone LP-201 SIP IP Phone Chapter 3 Configuring the Dynamix DW-Phone LP-201 through Web Pages The HTTPD web management interface provides user an easier way to configure rather than command line method through TELNET. The configuration function and steps are similar with the way through command line. Please refer to the chapter 4-Configuring the Dynamix DW-Phone LP-201 through Telnet command lines for more detail information. Below is a guide for user to configure via web interface.
Dynamix DW-Phone LP-201 SIP IP Phone Step 1. Browse the IP Address predefined via Keypad Please enter IP address (user have to set via LCD menu first) of Dynamix DW-Phone LP-201 in web browser. If user failed to set IP address via LCD menu, the default IP address of Dynamix DWPhone LP-201 is 10.1.1.3, user can try to connect to Dynamix DW-Phone LP-201 via this default IP via web interface.
Dynamix DW-Phone LP-201 SIP IP Phone Step 2. Input the login name and password Login name: root / user Note: Login with “user” only has authority as below: 1. Modify network configuration 2. Modify Phone Book 3. Change login password of “user” 4. Reboot Password (The same with TELNET): Null (just press confirm, no need to key in password in default value) Note: User can set password later in 8.PASSWORD via web interface.
Dynamix DW-Phone LP-201 SIP IP Phone Step 3. Enter the web interface main screen After enter login name and password, user can see web interface main screen as below. Step 4. Start to configure Most important items are Network Interface, SIP Information, and Phone Book (in Peer-to-Peer mode). Please remember to configure these commands before start to work with SIP-Phone. Note: After change any settings, please remember to reboot (in Reboot System) Dynamix DWPhone LP-201 so that changes can take effect.
Dynamix DW-Phone LP-201 SIP IP Phone 1. Network Interface Please refer to chapter 4.7 [ifaddr] command. - IP Address: Set IP Address of SIP-Phone - Subnet Mask: Set the Subnet Mask of SIP-Phone - Default routing gateway: Set Default routing gateway of SIP-Phone - Get IP Mode: User has to set Dynamix DW-Phone LP-201 to use which network mode. 1. Fixed IP: User has to assign a fixed IP to SIP-Phone. 2.
Dynamix DW-Phone LP-201 SIP IP Phone 27 User Manual
Dynamix DW-Phone LP-201 SIP IP Phone - SNTP: Enable / Disable the Simple Network Time Protocol function SNTP Server Address: Set SNTP Server Address When SNTP server is available, enable Dynamix DW-Phone LP-201 SNTP function to point to SNTP - server IP address so that Dynamix DW-Phone LP-201 can get correct current time. GMT: Set time zone for SNTP Server time User can set different time zone according to the location of SIP-Phone.
Dynamix DW-Phone LP-201 SIP IP Phone 2. SIP Information Please refer to chapter 4.13 [SIP] command - Run Mode: Select Dynamix DW-Phone LP-201 to work under Peer-to-Peer mode or Proxy mode. - Proxy IP Address: Set Proxy IP Address or URL address (Domain Name Server - - must be configured. Please refer to Network Interface). Outbound Proxy: Set IP Address or URL address (Domain Name Server must be configured. Please refer to Network Configure) of outbound Proxy server.
Dynamix DW-Phone LP-201 SIP IP Phone string here. For example, if Account Name is 123, Dynamix DW-Phone LP201 will sent out messages as Account Name @”IP address of Proxy”, if user set prefix as abc, Dynamix DW-Phone LP-201 will set out as abc123@”IP address of Proxy”. This function is for special proxy server. - Line Number: identify one number for the Dynamix DW-Phone LP-201 to register to the Proxy. Line Account: set user name of Dynamix DW-Phone LP-201 for registering.
Dynamix DW-Phone LP-201 SIP IP Phone 3. System Configuration Please refer to chapter 4.12 [sysconf] command - Keypad DTMF Type: set DTMF type. User can select DTMF type SIP-Phone transmits. RFC2833 Payload Type: change RFC2833 Payload type. This is for special request from the other site, if RFC2833 payload types of 2 sites are different, it may cause some problem of connection.
Dynamix DW-Phone LP-201 SIP IP Phone 4. PPPoE Configure Please refer to chapter 4.11[pppoe] command - User Name: Set PPPoE authentication User Name. Password: Set PPPoE authentication password.
Dynamix DW-Phone LP-201 SIP IP Phone 5. Voice Setting Please refer to chapter 4.15 [voice] command - Codec Priority: set codecs priority in order. Please notice that user can set from 1 to 5 codecs as their need. For example, user can only set first priority as G.723.1, and set the others as x, that means only G.723.1 is available. - Frame Size: User can set different packet size for each codec. G.723 Silence Suppression: Enable / Disable sound compression and comfort noise generation.
Dynamix DW-Phone LP-201 SIP IP Phone 6. Phone Book Please refer to chapter 4.10 [pbook] command - Add Data: User can specify 20 sets of phone book via web interface. Please input index, Name, IP Address and E.164 number of the destination device. Delete Date: User can delete any configured phone book data by index.
Dynamix DW-Phone LP-201 SIP IP Phone 7. DDNS Configuration Please refer to chapter 4.17 [ddns] command - Status: to enable/disable DDNS function Server: to choose one DDNS server, on which user has already registered. (Now only one DDNS server is available---www.dyndns.
Dynamix DW-Phone LP-201 SIP IP Phone 8. DSCP Configuration Please refer to chapter 4.16 [tos] command Set Signal or RTP Packet DSCP value: - Assured Forwarding (AF) PHB: Select Delay priority and Drop Precedence - Expedited Forwarding (EF) PHB: Select TOS value as EF - Default: Select TOS value as 0 - User Assign Special DSCP Code: User can set other unspecified value here.
Dynamix DW-Phone LP-201 SIP IP Phone DROP Precedence Class #1 Class #2 Class #3 Class #4 Low Drop Precedence (AF11) (AF21) (AF31) (AF41) 001010 010010 011010 100010 (AF12) (AF22) (AF32) (AF42) 001100 010100 011100 100100 (AF13) (AF23) (AF33) (AF43) 001110 010110 011110 100110 Medium Drop Precedence High Drop Precedence Please refer to RFC standard documents for more information about what is DSCP.
Dynamix DW-Phone LP-201 SIP IP Phone 9. Password Please refer to chapter 4.19 [password] command - Change: First select login name as root or user, then enter current password, new password and confirm new password again to set new password. Abort: Press abort will clean all inputs.
Dynamix DW-Phone LP-201 SIP IP Phone 10. Rom Configuration Please refer to chapter 4.18 [rom] command - FTP/TFTP Server IP Address: Set TFTP server IP address Target File name: Set file name prepared to upgrade Method: Select download method as TFTP or FTP FTP Login: Set FTP login name and password Target File Type: Select which sector of Dynamix DW-Phone LP-201 to upgrade Note: 1. After 2mb file download is finished, all configurations might change to default values, user has to configure again. 2.
Dynamix DW-Phone LP-201 SIP IP Phone 11. Flash Clean Please refer to 4.15 [flash] command. - Press CLEAN will clean all configurations of Dynamix DW-Phone LP-201 and reset to factory default value.
Dynamix DW-Phone LP-201 SIP IP Phone 12. Reboot System - Press reboot will reset SIP-Phone. Note: To execute reboot via web browser, Dynamix DW-Phone LP-201 will automatically save all data before reboot. To execute reboot via command, please remember to do Commit Data before Reboot System.
Dynamix DW-Phone LP-201 SIP IP Phone Chapter 4 Configuring the Dynamix DW-Phone LP-201 through Telnet command lines After setting the IP Address of Dynamix DW-Phone LP-201 and reboot, (please refer to LCD Menu: 5-3.4.5), user can enter into Telnet command lines. Note: 1. After user enter Dynamix DW-Phone LP-201 configuration via telnet, please use login: ”root”, password: null, press enter to enter command lines.
Dynamix DW-Phone LP-201 SIP IP Phone 2. [quit] command Type quit/exit/close will logout Dynamix DW-Phone LP-201 and Telnet Program. 3. [debug] command This command is for engineers to debug system of SIP-Phone. User can add debug flag via command debug –add “debug flags”, and then start debug function via command debug –open. When Dynamix DW-Phone LP-201 is working on screen will display related debug messages. Most frequently used debug flag are “sip”, “fsm”, “msg”…etc. 4.
Dynamix DW-Phone LP-201 SIP IP Phone 4. -delete: delete a record of certain listed index in phone book table. (pbook –delete “index number”) 5. -insert: insert a record in specified index of phone book. 6. -modify: modify record of a certain index in phone book. Please notice that the name, IP address and e164 number must be modified together; user cannot just modify one parameter only. (pbook –modify “index” name “X” ip “xxx.xxx.xxx.xxx” e164 “X”) 6.
Dynamix DW-Phone LP-201 SIP IP Phone 8. [time] command When Dynamix DW-Phone LP-201 enables SNTP function and be able to connect with SNTP server, type time command will show the current time retrieved from SNTP server. 9. [ifaddr] command Configure and display the Dynamix DW-Phone LP-201 IP information. 1. –print: print out all current configurations of ifaddr command. 2. -ip, -mask, -gate: Set Dynamix DW-Phone LP-201 IP Address, subnet mask and default gateway respectively. 5.
Dynamix DW-Phone LP-201 SIP IP Phone 9. -ipsharing: If Dynamix DW-Phone LP-201 is behind an IP-sharing, user must enable IP sharing function and specify public IP address. (ifaddr –ipsharing 0/1 “public IP address of IP sharing”, 0 for disable and 1 for enable) Note: Some Proxy servers support endpoint behind NAT function, in this case Dynamix DW-Phone LP-201 doesn’t have to enable IP sharing function, please contact with your Proxy Server vendor. 10. –upnp: enable/disable UPnP function.
Dynamix DW-Phone LP-201 SIP IP Phone 10. [pppoe] command 1. 2. 3. 4. -print: display all current configurations and information. –id: to set PPPoE authentication user name. –pwd: to set PPPoE authentication password. –reboot: Choose enable or disable this function.
Dynamix DW-Phone LP-201 SIP IP Phone 12. [sysconf] command 1. -print: display all current configurations. 2. -idtime: set the duration (in second) of two pressed digits in dial mode as timed out. If after the duration user hasn’t pressed next number, Dynamix DW-Phone LP201 will dial out all number pressed. 3. –service: set SIP Phone to work as normal mode or hotline mode. If user wants to use hotline function, please set service to be 1, and set bureau related configuration. Please refer to 19.
Dynamix DW-Phone LP-201 SIP IP Phone 13. [sip] command 1. –print: display all current configurations. 2. –mode: configure Dynamix DW-Phone LP-201 as Proxy or Peer-toPeer Mode. Usage: sip –mode 0/1(1 for Proxy mode, 0 for Peer-to Peer mode) 3. –px: set proxy server IP address or URL address (sip –px “IP address or URL of Proxy server”). 4. –pxport: set listening port of Proxy server. 5. –outpx: set IP address of outbound proxy server.
Dynamix DW-Phone LP-201 SIP IP Phone 9. –expire: set expire time of registration. Dynamix DW-Phone LP-201 will keep reregistering to proxy server before expire timed out. 10. –port: set listening UDP port or SIP-Phone. 11. –rtp: set RTP port number. Dynamix DW-Phone LP-201 will use this port to send and receive voice. 14. [security] command 1. –print: display all current configurations. 2. -name: set user ID of Dynamix DW-Phone LP-201 for registering. User can set user name and password for registering.
Dynamix DW-Phone LP-201 SIP IP Phone 15. [voice] command The voice command is associated with the voice codec setting information. 1. -print: display voice codec information and configuration. 2. -send: three voice packet size can be configured as 20 ms, 40 ms or 60 ms. (only 30 and 60 ms for G.723.1) 3. -priority: set codecs priority in order.
Dynamix DW-Phone LP-201 SIP IP Phone 16. [tos] command TOS/DiffServ (DS) priority function can discriminate the Differentiated Service Code Point (DSCP) of the DS field in the IP packet header, and map each Code Point to a corresponding egress traffic priority. As per the definition in RFC2474, the DS field is Type-of-Service (TOS) octet in IPv4. The recommended DiffServ Code Point is defined in RFC2597 to classify the traffic into different service classes.
Dynamix DW-Phone LP-201 SIP IP Phone 010110 011110 100110 ====> 22 (Decimal System) ====> 30 (Decimal System) ====> 38 (Decimal System) 000000 ====> 0 (Decimal System) DROP Precedence Class #1 Class #2 Class #3 Class #4 Low Drop Precedence (AF11) (AF21) (AF31) (AF41) 001010 010010 011010 100010 (AF12) (AF22) (AF32) (AF42) 001100 010100 011100 100100 (AF13) (AF23) (AF33) (AF43) 001110 010110 011110 100110 Medium Drop Precedence High Drop Precedence 1.
Dynamix DW-Phone LP-201 SIP IP Phone 17. [ddns] command This function is for Dynamic Domain Name Server service. Once user register to one DDNS server, he can specify domain name for the SIP Phone. When SIP Phone reboot, it will automatically update it’s IP address to DDNS server. In this way, even SIP Phone is using dynamic IP address, other endpoint can locate this SIP Phone by its domain name. 1. -print: display DDNS overall information and configuration. 2. –enable: to enable/disable DDNS function.
Dynamix DW-Phone LP-201 SIP IP Phone 18. [vlan] command 1. -print: display current VLAN configuration settings. 2. -dev: enable/disable VLAN configuration. 3. –vid: set CPU VLAN ID number. 4. –pcvid: set PC port VLAN ID number. Note: Only when vid numbers are the same, network can connect.
Dynamix DW-Phone LP-201 SIP IP Phone 19. [bureau] command 1. -print: show all current configurations. 2. -hotline: set hotline table. User can set hotline function to specify one IP address for Dynamix DW-Phone LP-201 to dial out directly. Once user picks up SIP-Phone, it will automatically dial out to the assigned IP address and number.
Dynamix DW-Phone LP-201 SIP IP Phone 20. [rom] command 1. -print: show all current configurations and version information. 2. -app,-boot, -dsptest, -dspcore, -dspapp,: upgrade main boot code, main application code, DSP testing code, DSP kernel code, DSP application code, Ring Back Tone PCM file and Hold Tone . Note: After upgrade Application, please remember to execute flash –clean command, which will clean all configurations become factory values except IP address. 3.
Dynamix DW-Phone LP-201 SIP IP Phone 21. [passwd] command For security protection, user has to input the password before entering application user/config mode. Two configurations of login name/password are supported by the system. 1. –set: set password of “root” users or “user” users. (passwd –set root/user “password”) 2. –clean: clean up password restored before, and user can login :”root/user, password: ”press enter”.
Dynamix DW-Phone LP-201 SIP IP Phone Chapter 5 Upgrading Software on the Dynamix DW-Phone LP201 SIP-Phone Dynamix DW-Phone LP-201 supports three methods to upgrade the new version. All methods are necessary to prepare the TFTP or FTP program on the host PC as TFTP/FTP server. After installing TFTP/FTP program on one PC and connecting to network, Dynamix DW-Phone LP-201 is ready to be upgraded. 1. LCD Panel Control 2. Remote Control: Telnet 3. Web Management 1.
Dynamix DW-Phone LP-201 SIP IP Phone (7) Start to Upgrade Select YES or NO to start upgrade. After download is finished, press OK then Dynamix DW-Phone LP-201 will ask if need to reboot. 2. Web Management Please refer to chapter 4.
Dynamix DW-Phone LP-201 SIP IP Phone which will clean all configurations become factory values except IP address. 3. Remote Control: Telnet Please refer to chapter 4.18 [rom] command 1. -print: show all current configurations and version information. 2. -app,-boot, -dsptest, -dspcore, -dspapp,: upgrade main boot code, main application code, DSP testing code, DSP kernel code, DSP application code, Ring Back Tone PCM file and Hold Tone .
Dynamix DW-Phone LP-201 SIP IP Phone Command rom –print can show current version installed in Dynamix DW-Phone LP-201 .