Dynamix DW Phone LP - 201 VoIP Phone (H.
Dynamix DW-Phone LP-201 VoIP Phone Chapter 1 Overview of the Dynamix DW-Phone LP-201 ..................................................... 3 1. Hardware Overview ........................................................................................... 4 2.Software Features and Specification .................................................................. 8 Calling Features............................................................................................................
Dynamix DW-Phone LP-201 VoIP Phone 11. [pppoe] command ................................................................................................. 52 12. [sysconf] command ............................................................................................... 53 13. [h323] command ................................................................................................... 54 14. [voice] command..............................................................................................
Dynamix DW-Phone LP-201 VoIP Phone Chapter 1 Overview of the Dynamix DW-Phone LP-201 Dynamix DW-Phone LP-201 is a full-featured IP-based telephone set via Ethernet base communication. Over the office LAN connection, it provides IP-PBX solution such as stationto-station call, IP call and local PSTN/PBX Extension call via PSTN Gateway. The traditional PBX functionality is provided with H.450 features together with Gatekeeper or IP/PBX Call Manager.
Dynamix DW-Phone LP-201 VoIP Phone 1. Hardware Overview 1.Front View and Keypad function ♦ ♦ ♦ ♦ C: Cancel and Clear ³´ : Move to left /previous and right/next. OK: Press OK to confirm the modification. Direct Line (DL) Button 1 – 10: User press DL button to do speed dial according to phone book data 1-10 (please refer to LCD configuration-Phone Address Book, Advanced Configurations via Telnet- [pbook] command, or Web Configuration-Phone Book chapter).
Dynamix DW-Phone LP-201 VoIP Phone ♦ ♦ ♦ Number 1 –10, * and #: The function is as the same as the general phone set. Corresponding list of keypad and symbol: 1 “1” 2 “A” ; “ B” ; “C” ; “2” 3 “D” ; “E” ; “F” ; “3” 4 “G” ; “H” ; “I” ; “4” 5 “J” ; “K” ; “L” ; “5” 6 “M” ; “N” ; “O” ; “6” 7 “P” ; “Q” ; “R” ; “S” ; “7” 8 “T” ; “U” ; “V” ; “8” 9 “W” ; “X” ; “Y” ; “Z” ; “9” * “.
Dynamix DW-Phone LP-201 VoIP Phone ♦ MESSAGE and its indicated LED light: When missed incoming calls, the MESSAGE LED will be flashing. User can check the information of missed calls by pressing the MESSAGE button. ♦ TRANSFER: 1. Transfer a call by H.450 transfer function. Press TRANSFER button in communication and press phone number which user want to transferred to can transfer this call. 2.
Dynamix DW-Phone LP-201 VoIP Phone 3.Specification of connector 1、 Ethernet Port: Ethernet port is for connecting Dynamix DW - Phone LP-201 IP Phoneto network, transmit rate supports 10/100 Base-T. Ethernet connector(LAN) 2、 RJ11connector: RJ11 connector is for connecting Dynamix DW - Phone LP-201 IP Phonewith PSTN.
Dynamix DW-Phone LP-201 VoIP Phone 2.
Dynamix DW-Phone LP-201 VoIP Phone Provisioning and Configuration H.235 security function Support Fast Start and H.245 Tunneling Can set up to ten E.164 phone number LCD configuration password protection Automatically Gatekeeper Discovery Alternate Gatekeeper selection Provide Gatekeeper Mode or Peer-to-Peer Mode (Non Gatekeeper needed) selection Ring tone, Speaker and Handset volume adjustable Dial path selection (PSTN or IP mode) Compatible with MS-NetMeeting v3.
Dynamix DW-Phone LP-201 VoIP Phone Function Keys: Speaker, Redial, Mute, Hold, Transfer, Forward, Message, PSTN Ten sets last Phone Number redial Dial plan Provide TOS (Type Of Service) function Gatekeeper mode or Peer to Peer mode selection Caller ID: IP side display H323-ID and E.164. Display the count of total call received. Display un-answered call name, number. Show caller’s name, number, calling time. Volume Adjustment: Speaker volume level adjustable.
Dynamix DW-Phone LP-201 VoIP Phone Firmware Upgrade: Firmware version displayed on LCD and Web. Three ways to upgrade firmware: - Download via KEYPAD configuration (can only upgrade application rom file) . - Download via Telnet.
Dynamix DW-Phone LP-201 VoIP Phone Chapter 2 Configuring the Dynamix DW-Phone LP-201 through Phone menus Note: 1. After any configurations be made for the LAN Phone 101/201, user has to do Reboot in the selection 1→ 6 “Reboot”. 2. We suggest user to set IP address via LCD menu 1→ 1 first, then go to chapter 3 to do other detail configurations via web browser. 1.Initialize Dynamix DW-Phone LP-201 1. When power on the Dynamix DW-Phone LP-201 , the LCD screen shows as below.
Dynamix DW-Phone LP-201 VoIP Phone Press ³ or ´ to enter configuration mode then press OK button to enter certain menu. 1. 2. 3. 4. 5. 6. System Configuration (mandatory, protected by password) User Line Number (mandatory) Ring Configuration Indicate Forward Type Message Box Phone Address Book Note: LCD Panel of Dynamix DW-Phone LP-201 is operated manually by moving ³ or ´ on the keypad. Press OK to enter separate configuration menu. Press C to go back to the main menu.
Dynamix DW-Phone LP-201 VoIP Phone 2.LCD Configuration User can set the following configurations manually by operating the commands displayed on LCD. 1. System Configuration (mandatory, protected by password) Please Enter Password: User must key in password to enter this menu, selections under this command are all important ones, which can only be configured by administrators. Note: 1.Password to enter System Configuration: The same as H.323 token password (please refer to item (11)), default value is x.
Dynamix DW-Phone LP-201 VoIP Phone (5) Secondary DNS User can set IP address of secondary DNS, once primary DNS cannot work normally, Dynamix DW - Phone LP-201 VoIP can refer to secondary DNS. (6) Gatekeeper User has to offer one available Gatekeeper server IP Address and set this IP Address on the Dynamix DW - Phone LP-201 VoIP keypad.
Dynamix DW-Phone LP-201 VoIP Phone (11) Token Password (A) LCD menu password: User can enter LCD system configuration by key in this password (B) H.235 security: To set RRQ/ARQ authentication token password. If Dynamix DW - Phone LP-201 VoIP wants to register to a Gatekeeper, which implement H.235 security token feature, LAN Phone has to set a RRQ/ARQ authentication token password, which is provided by Gatekeeper manager.
Dynamix DW-Phone LP-201 VoIP Phone (4) Indicate file name User has to press the file name of new application rom file prepared for upgrading (5) Start Download Press OK to start download new application rom file. After download is finished, Dynamix DW - Phone LP-201 IP Phonewill automatically reboot. (6) Firmware Version Show versions of all rom files and hardware. Note: 1.Download via LCD command can only upgrade new application rom file. 2.
Dynamix DW-Phone LP-201 VoIP Phone 2. User Line Number User has to identify at least one number for the Dynamix DW-Phone LP-201 to register to the Gatekeeper. User can set up to 10 different numbers for one IP Phone. (1) Line Number 1 (2) Line Number 2 (3) Line Number 3 (4) Line Number 4 (5) Line Number 5 (6) Line Number 6 (7) Line Number 7 (8) Line Number 8 (9) Line Number 9 (10) Line Number 10 Note: User can set six zero “000000” on LCD to disable this number and the number after this one. Ex.
Dynamix DW-Phone LP-201 VoIP Phone A. Busy When Dynamix DW-Phone LP-201 is in busy status, the incoming call will be directly forwarded to the assigned phone number. B. No response When Dynamix DW-Phone LP-201 is continuing ringing around 10 seconds, the incoming call will be directly forwarded to the assigned phone number. C. Unconditional It is included the above two types. Whether the IP Phone is in which status, it will be automatically forwarded to the assigned phone number.
Dynamix DW-Phone LP-201 VoIP Phone 7. PPPoE Information All items below can only be displayed when PPPoE connection is established, user can check related information here. 1. PPPoE Status 2. 3. 4. 5. 6. 7. 8. 9.
Dynamix DW-Phone LP-201 VoIP Phone Chapter 3 Configuring the Dynamix DW-Phone LP-201 through Web Pages The HTTPD web management interface provides user a easier way to configure rather than command line method through TELNET. The configuration function and step is similar with the way through command line. Please refer to the chapter 4-Advanced Configurations via Telnet for more detail information. Below is a guide for user to configure via web interface.
Dynamix DW-Phone LP-201 VoIP Phone Step 1. Browse the IP Address predefined via Keypad Please enter IP address (user can set via LCD menu first) of Dynamix DW - Phone LP-201 VoIP in web browser. If user failed to set IP address via LCD menu, the default IP address of Dynamix DW - Phone LP-201 VoIP is 10.1.1.3, user can try to connect to Dynamix DW - Phone LP-201 VoIP via this default IP via web interface.
Dynamix DW-Phone LP-201 VoIP Phone Step 2. Input the login name and password f Login name: root / administrator f Password (The same with TELNET): Null (just press confirm no need to key in password in default value) Note: User can set password later in 12.PASSWORD via web interface.
Dynamix DW-Phone LP-201 VoIP Phone Step 3. The web interface main screen After enter login name and password, user can see web interface main screen as below. Step 4. Start configure Most of all commands displayed in telnet are transfer to web interface. Most important items are Network Configure, H323 Configure, and System Command. Please remember to configure these commands before start to work with IP Phone.
Dynamix DW-Phone LP-201 VoIP Phone 1. Network Configure Please refer to chapter 4.6 [ifaddr] command.
Dynamix DW-Phone LP-201 VoIP Phone - DHCP: Enable / Disable to DHCP mode When DHCP function enables, Dynamix DW-Phone LP-201 will automatically search DHCP server after reboot. Note: After Dynamix DW - Phone LP-201 VoIP catches a dynamic IP address form DHCP server, user can see this IP address on LCD connect configuration. When user checks Network Configure via web interface, browser will pop up one small window for current DHCP network information.
Dynamix DW-Phone LP-201 VoIP Phone - IP Address: Set IP Address of IP Phone Subnet Mask: Set the Subnet Mask of IP Phone Default gateway: Set Default routing gateway of IP Phone Domain Name Server: Set Domain Name Server IP address. User can set Domain Name Server IP address. Once Dynamix DW - Phone LP-201 VoIP can connect with DNS server, user can specify URL address instead of IP address for Gatekeeper and phone book IP address. (Please refer to 4.13 [h323] command and 4.
Dynamix DW-Phone LP-201 VoIP Phone 2. H323 Configure Please refer to chapter 4.13 [h323] command - Mode: Select GK mode or Peer-to-Peer mode Gatekeeper IP Address: Set Gatekeeper IP Address or URL address (Domain Name Server must be configured. Please refer to Network Configure). User can also set IP as 255.255.255.255 and let Dynamix DW - Phone LP-201 IP Phoneauto discovery for Gatekeeper. Please notice that in this case user must enable Gatekeeper discovery function.
Dynamix DW-Phone LP-201 VoIP Phone - Gatekeeper ID: Set Gatekeeper ID (Gatekeeper Name) Gatekeeper Discovery: Enable/Disable GRQ function Set Gatekeeper name for Gatekeeper discovery. When IP Phone send out Gatekeeper discovery message will search Gatekeeper with this Gatekeeper name. - RAS Time To Live (TTL)(0~3600): set RAS TTL time (0-3600 second). Dynamix DW - Phone LP-201 VoIP will keep re-registering to GK before TTL timed.
Dynamix DW-Phone LP-201 VoIP Phone (A) LCD menu password: User can enter LCD system configuration by key in this password and default value is lowercase “x.” (Press TRANSFER to switch lowercase and uppercase, then press 9 twice). (B) H.235 security: To set RRQ/ARQ authentication token password. If Dynamix DW - Phone LP-201 VoIP wants to register to a Gatekeeper, which implement H.
Dynamix DW-Phone LP-201 VoIP Phone 3. System Configure Please refer to chapter 4.12 [sysconf] command - Keypad Type: set DTMF type. User can select DTMF type Dynamix DW - Phone LP201 VoIP receive and transmit. - Dial Plan: Set dialed DTMF digit limitation (0 is for any digits) It is for setting dial-numbering plan. While user will dial out e164 number only for three digits, the plan can be set as 3. Once input 3 digits, LAN Phone will immediately dial out.
Dynamix DW-Phone LP-201 VoIP Phone - Digit Type of End of Dialing: select end of dialing key, e.g. set end of dial key as OK button, after finished pressing dialing number then press OK will dial out. H.450 Related Features: Enable/Disable H.450 Button functions, which include transfer, hold and forward. Please Note that disable this function will cause TRANSFER button lost function of switching characters to be lower or upper case.
Dynamix DW-Phone LP-201 VoIP Phone 4. PPPoE Configure Please refer to chapter 4.11[pppoe] command - Device: Enable/Disable PPPoE function User Name: Set PPPoE authentication User Name. Password: Set PPPoE authentication password.
Dynamix DW-Phone LP-201 VoIP Phone 5. DDNS Configure Please refer to chapter 4.10 [ddns] command - Status: to enable/disable DDNS function Server: to choose one DDNS server, on which user has already registered. (Now only one DDNS server is available---www.dyndns.
Dynamix DW-Phone LP-201 VoIP Phone 6. Voice Configure Please refer to chapter 4.14 [voice] command - Codec Priority: set codecs priority in order. Please notice that user can set from 1 to 7 codecs as their need. For example, user can only set first priority as G.723.1, and set the others as x, that means only G.723.1 is available. - Sending Packet Size: User can set different packet size for each codec. (For - Advanced User) G.
Dynamix DW-Phone LP-201 VoIP Phone 7. Tone Configure (For Advanced User) Please refer to chapter 4.16 [tone] command - Busy Tone PSTN call waiting tone (When Dynamix DW - Phone LP-201 VoIP is in communication with IP mode and has PSTN incoming call) - Dial Tone Dynamix DW-Phone LP-201 is configurable of busy tone, PSTN call waiting tone and dial tone. User must key in 8 sets of number to finish this configuration. If it is singlefrequency tone, please set high frequency and related items as 0.
Dynamix DW-Phone LP-201 VoIP Phone - Hold Tone Generation (using PCM file): Enable/Disable hold tone generation If other terminals support H.450 hold function, and execute hold function when connecting with VoIP, user will hear hold tone from VoIP.
Dynamix DW-Phone LP-201 VoIP Phone 9. Support Functions (Function of this page will work only when 2 sides of communication both supports.) Please refer to chapter 4.17 [support] command - Fast Start: Enable/disable to do Fast Start function. H.245 Tunneling: Enable/disable H.245 Tunneling function. H.245 Separate Channel: Enable/Disable function of opening H.245 channel after fast start connection.
Dynamix DW-Phone LP-201 VoIP Phone 10. DSCP Configure Please refer to chapter 4.15 [tos] command Set Signal or RTP Packet DSCP value: - Assured Forwarding (AF) PHB: Select Delay priority and Drop Precedence - Expedited Forwarding (EF) PHB: Select TOS value as EF - Default: Select TOS value as 0 - User Assign Special DSCP Code: User can set other unspecified value here.
Dynamix DW-Phone LP-201 VoIP Phone DROP Precedence Class #1 Class #2 Class #3 Class #4 Low Drop Precedence (AF11) (AF21) (AF31) (AF41) 001010 010010 011010 100010 (AF12) (AF22) (AF32) (AF42) 001100 010100 011100 100100 (AF13) (AF23) (AF33) (AF43) 001110 010110 011110 100110 Medium Drop Precedence High Drop Precedence Please refer to RFC standard documents for more information about what is DSCP.
Dynamix DW-Phone LP-201 VoIP Phone 11. Phone Book Please refer to chapter 4.9 [pbook] command - Add Data: User can specify 20 sets of phone book via web interface. Please input index, Name, IP Address and E.164 number of the destination device. Delete Date: User can delete any configured phone book data by index.
Dynamix DW-Phone LP-201 VoIP Phone 12. Password Please refer to chapter 4.20 [password] command - Change: First select login name as root or administrator, then enter current password, new password and confirm new password again to set new password. Abort: Press abort will clean all inputs.
Dynamix DW-Phone LP-201 VoIP Phone 13. Firmware Upgrade Please refer to chapter 4.19 [rom] command - Download Method: Select download method as TFTP or FTP - Server IP Address: Set TFTP server IP address - FTP Login: Set FTP login name and password - Target File name: Set file name prepared to upgrade - Target File Type: Select which sector of Dynamix DW - Phone LP-201 VoIP to upgrade Note: 1.
Dynamix DW-Phone LP-201 VoIP Phone 14. System Command - Press CLEAN will clean all configurations of Dynamix DW - Phone LP-201 VoIP and reset to factory default value. Note: User must re-configure all commands all over again (except Network Configure) once execute this function, - Press reboot will reset IP Phone. Note: To execute reboot via web browser, Dynamix DW - Phone LP-201 VoIP will automatically save all data before reboot. To execute command, please remember to do commit before reboot.
Dynamix DW-Phone LP-201 VoIP Phone 15. Version Information Display all current version lists of hardware and software.
Dynamix DW-Phone LP-201 VoIP Phone Chapter 4 Configuring the Dynamix DW-Phone LP-201 through Telnet command lines After initializing the Dynamix DW-Phone LP-201 VoIP IP Address setting (please refer to LCD Configuration: 1.Connect Configuration), user can enter into configuration mode via telnet. Note: 1. After user enter LAN Phone configuration via telnet, please use login: ”root”, password: null, press enter to enter command line. 2.
Dynamix DW-Phone LP-201 VoIP Phone 2. [quit] command Type quit/exit/close will logout Dynamix DW-Phone LP-201 and Telnet Program. 3. [reboot] command After typing commit command, type reboot to restart the Dynamix DW-Phone LP201 . Sometimes after user type reboot, on terminal screen will display:"Data modified, commit to flash rom?", which means Dynamix DW - Phone LP-201 IP Phonewill record call history or not.(ex. REDIAL, outgoing and incoming call data) 4.
Dynamix DW-Phone LP-201 VoIP Phone 5. [commit] command Save any changes after configuring the Dynamix DW-Phone LP-201 . 6. [ifaddr] command Configure and display the Dynamix DW-Phone LP-201 IP information. 1. -ip, -mask, -gate: Set Dynamix DW-Phone LP-201 IP Address, subnet mask and default gateway respectively. 2. -dhcp: When DHCP function enables (ifaddr –dhcp 1), Dynamix DW-Phone LP-201 will automatically search DHCP server after execute the commit and reboot command.
Dynamix DW-Phone LP-201 VoIP Phone 8. –http: set http port. User can configure Dynamix DW - Phone LP-201 VoIP via web browser, default http port is 80, if port 80 is not available or user has more than 1 Dynamix DW - Phone LP-201 VoIP behind NAT, http port can be changed to another available port. 7.
Dynamix DW-Phone LP-201 VoIP Phone 8. [ping] command Command ping can test which the IP address is reachable or not. Usage: ping “xxx.xxx.xxx.xxx(IP address)” The message will display packets transmitting condition or no answer from the IP address. 9. [pbook] command The command is for Peer-to-Peer Mode use only. Therefore, VoIP products such as Dynamix DW-Phone LP-201 VoIP that support Peer-to-Peer Mode are also available to be addressed on the Dynamix DW-Phone LP-201 phone book. 1.
Dynamix DW-Phone LP-201 VoIP Phone 10. [ddns] command This function is for Dynamic Domain Name Server service. Once user register to one DDNS server, he can specify domain name for the IP Phone. When Dynamix DW Phone LP-201 VoIP reboot, it will automatically update it’s IP address to DDNS server. In this way, even Dynamix DW - Phone LP-201 VoIP is using dynamic IP address, other endpoint can locate this Dynamix DW - Phone LP-201 VoIP by its domain name. 1.
Dynamix DW-Phone LP-201 VoIP Phone this time. (ddns –delay 1-59m/1-24h , m means minute, h means hour) 10. –force: to force to execute DDNS update. Once user enters this command, Dynamix DW - Phone LP-201 VoIP will update DDNS data immediately. (ddns – force “IP address of IP Phone”) Note: 1. For now we only support DDNS server as www.dyndns.org and www.3322.org. 2. User must register to DDNS server first, and specify user name and password in ddns -id and ddns –passwd. 3.
Dynamix DW-Phone LP-201 VoIP Phone 12. [sysconf] command This command displays the system information and configuration. 1. -print: display system overall information and configuration. 2. -plan: It is for setting dial-numbering plan. While user will dial out e164 number only for three digits, the plan can be set as 3. Once input 3 digits, Dynamix DW - Phone LP-201 VoIP will immediately dial out.
Dynamix DW-Phone LP-201 VoIP Phone 13. [h323] command 1. –print: display H.323 stack information and configuration. 2. –mode: configure Dynamix DW-Phone LP-201 as Gatekeeper or Peer-to-Peer Mode. Usage: h323 –mode 0/1(0 for Gatekeeper mode, 1 for Peer-to-Peer mode) 3. –gk: set Main Gatekeeper IP address(h323 –gk “xxx.xxx.xxx.xxx”) or URL address( Domain Name Server must be configured. Please refer to 4.6 [ifaddr] command). User can set IP as 255.255.255.
Dynamix DW-Phone LP-201 VoIP Phone 5. –algk: set IP address or URL address( Domain Name Server must be configured. Please refer to 4.6 [ifaddr] command) of alternative Gatekeeper. If VoIP tries to register to main Gatekeeper for 10 times but still fail, Dynamix DW - Phone LP201 will try to register to alternative Gatekeeper. 6. –gkname: set Gatekeeper name for Gatekeeper discovery. When Dynamix DW Phone LP-201 send out Gatekeeper discovery message will search Gatekeeper with this Gatekeeper name.
Dynamix DW-Phone LP-201 VoIP Phone 12. –rtp: assign RTP port number(1024-65535). Dynamix DW - Phone LP-201 need 2 RTP ports for voice communication, the port number assigned here is a base, for example, default value is 16384, that means VoIP will use port 16384 and 16385 for RTP packets. - –ttl: set RAS TTL time (0-3600 second). Dynamix DW - Phone LP-201 will keep reregistering to GK before TTL timed. 13. –gkfind: assign Gatekeeper finding port number(1024-65535) 14.
Dynamix DW-Phone LP-201 VoIP Phone 14. [voice] command The voice command is associated with the voice codec setting information. 1. -print: display voice codec information and configuration. There are five voice codecs included in Dynamix DW-Phone LP-201 :G.723.1, G.711u, G.711A, G.729a, G.729, G.729ab, G.729b. 2. -send: three voice packet size can be configured as 20 ms, 40 ms or 60 ms.(only 30 and 60 ms for G..723) 3. -priority: set codecs priority in order.
Dynamix DW-Phone LP-201 VoIP Phone 8. -maxdealy:set maximum delay of jitter buffer(0~150) Note: It is for advanced administrator use only. Please ask your distributor before changing any settings of this command. 14. [rbtone] command 1. -print: display rbtone information and configuration. 2. -mode: set ring back tone generation mode.
Dynamix DW-Phone LP-201 VoIP Phone 1. High priority with DS-field. (1) Expected Forwarding (EF) 101110 (2) Assured Forwarding (AF) 2.
Dynamix DW-Phone LP-201 VoIP Phone IP Packet ToS information: Signaling Packet: DSCP Code: 10 <====== Configure control signal DSCP code Media Packet: DSCP Code: 10 <====== Configure RTP (voice) DSCP code usr/config$ Or, the ToS function can be configured via Web Browser selection by entering the above DSCP Decimal Code. This command is for setting IP packet TOS values to determine IP Packets priority on network. 1. -print : display current TOS values configurations. 2.
Dynamix DW-Phone LP-201 VoIP Phone frequency and related items as 0. Furthermore, unit of on/off time is 10 ms, and suggest keeping level as default value (8). User can also increase the value of level to increase the volume. 17. [support] command 1. -print : display current SUPPORT values configurations. 2. -fstart: enable or disable fast start (support –fstart 0/1 , 0 for disable and 1 for enable.
Dynamix DW-Phone LP-201 VoIP Phone 18. [bureau] command Type bureau can display commands below. 1. -print: display bureau line information and configuration. 2. -hold: set hold tone generation on or off. If other terminals support H.450 hold function, and execute hold function when connecting with Dynamix DW-Phone LP-201 , user will hear hold tone from Dynamix DW-Phone LP-201 . (0 for off,1 for on) 19.[rom] command 1. -print: show versions of all rom files. 2.
Dynamix DW-Phone LP-201 VoIP Phone Note: 1. After 2mb file download is finished, all configurations might change to default value, user has to configure again. 2. MAC address might change to default value also, please MUST use command setmac: Usage: key in command setmac key in MAC address with format: 0001a800xxxx 4. -s: it is necessary to prepare TFTP/FTP server IP address for upgrading firmware rom file. 5. -f: the file name prepared for upgrading is necessary as well. 5.
Dynamix DW-Phone LP-201 VoIP Phone Command rom –print can show current version installed in Dynamix DW-Phone LP-201 . 20. [passwd] command For security protection, user has to input the password before entering application user/config mode. Two configurations of login name/password are supported by the system. 1. –set: set password of “root” users or “administrator” users. (password –set root/administrator “password”) 2.
Dynamix DW-Phone LP-201 VoIP Phone 65
Dynamix DW-Phone LP-201 VoIP Phone Chapter 5 Upgrading Software on the Dynamix DW-Phone LP201 Dynamix DW-Phone LP-201 supports three methods to upgrade the new version. All methods are necessary to prepare the TFTP or FTP program on the host PC as TFTP/FTP server. After installing TFTP/FTP program on one PC and connecting to network, Dynamix DW-Phone LP-201 is ready to be upgraded. 1. LCD Panel Control 2. Remote Control: Telnet 3. Web Management *Download Procedure 1.LCD Panel Control 1.
Dynamix DW-Phone LP-201 VoIP Phone 2.Remote Control: Telnet Associated with the Chapter 4.19 [rom] command: 1. -print: show versions of all rom files. 2. -app,-boot, -dsptest, -dspcore, -dspapp, -rbpcm and -htpcm: upgrade main boot code, main application code, DSP testing code, DSP kernel code, DSP application code, Ring Back Tone PCM file and Hold Tone . 3. -s: it is necessary to prepare TFTP/FTP server IP address for upgrading rom file. 4. -f: the file name prepared for upgrading is necessary as well. 8.
Dynamix DW-Phone LP-201 VoIP Phone 3.Web Management - Download Method: Select download method as TFTP or FTP Server IP Address: Set TFTP server IP address FTP Login: Set FTP login name and password Target File name: Set file name prepared to upgrade Target File Type: Select which sector of Dynamix DW - Phone LP-201 to upgrade Note: 1. After 2mb file download is finished, all configurations might change to default values, user has to configure again. 2.