User Manual

A.
B.
C.
P.
E.
F.
G.
H.
I.
J.
K.
M.
N.
D.
Q.O. R.
S.
N.
L.
NOTICE
All instructions, warranties and other collateral documents are subject to change
at the sole discretion of Horizon Hobby, Inc. For up-to-date product literature, visit
horizonhobby.com and click on the support tab for this product.
Meaning of Special Language
The following terms are used throughout the product literature to indicate various
levels of potential harm when operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical
property damage AND a little or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of
physical property damage AND a possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of
property damage, collateral damage, and serious injury OR create a high probability
of superficial injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the
features of the product before operating. Failure to operate the product
correctly can result in damage to the product, personal property and cause
serious injury.
This is a sophisticated hobby product. It must be operated with caution and common
sense and requires some basic mechanical ability. Failure to operate this Product
in a safe and responsible manner could result in injury or damage to the product or
other property. This product is not intended for use by children without direct adult
supervision. Do not attempt disassembly, use with incompatible components or
augment product in any way without the approval of Horizon Hobby, Inc. This manual
contains instructions for safety, operation and maintenance. It is essential to read
and follow all the instructions and warnings in the manual, prior to assembly, setup
or use, in order to operate correctly and avoid damage or serious injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
SAFETY PRECAUTIONS AND WARNINGS
WARNING: Failure to exercise caution while using this product and comply
with the following warnings could result in product malfunction, electrical
issues, excessive heat, FIRE, and ultimately injury and property damage.
• Neverleavethepowersupply,chargerandbatteryunattendedduringuse.
• Neverattempttochargedead,damagedorwetbatterypacks.
• Neverattempttochargeabatterypackcontainingdifferenttypesofbatteries.
• Neverallowchildrenunder14yearsofagetochargebatterypacks.
• Neverchargebatteriesinextremelyhotorcoldplacesorplaceindirectsunlight.
• Neverchargeabatteryifthecablehasbeenpinchedorshorted.
• Neverconnectthechargerifthepowercablehasbeenpinchedorshorted.
• Neverconnectthechargertoanautomobile12Vbatterywhilethevehicle
is running.
• Neverattempttodismantlethechargeroruseadamagedcharger.
• NeverattachyourchargertobothanACandaDCpowersourceatthesametime.
• Neverconnecttheinputjack(DCinput)toACpower.
• Alwaysuseonlyrechargeablebatteriesdesignedforusewiththistypeofcharger.
• Alwaysinspectthebatterybeforecharging.
• Alwayskeepthebatteryawayfromanymaterialthatcouldbeaffectedbyheat.
• Alwaysmonitorthechargingareaandhaveareextinguisheravailableatalltimes.
• Alwaysendthechargingprocessifthebatterybecomeshottothetouchorstarts
tochangeform(swell)duringthechargeprocess.
• Alwaysconnectthechargecabletothechargerrst,thenconnectthebatteryto
avoid short circuit between the charge leads. Reverse the sequence when
disconnecting.
• Alwaysconnectthepositiveredleads(+)andnegativeblackleads(–)correctly.
• Alwaysdisconnectthebatteryaftercharging,andletthechargercoolbetween
charges.
• Alwayschargeinawell-ventilatedarea.
• AlwaysterminateallprocessesandcontactHorizonHobbyiftheproduct
malfunctions.
WARNING: Never leave charger unattended, exceed maximum charge rate,
charge with non-approved batteries or charge batteries in the wrong mode.
Failure to comply may result in excessive heat, fire and serious injury.
CAUTION: Always ensure the battery you are charging meets the
specifications of this charger and that the charger settings are correct. Not
doing so can result in excessive heat and other related product malfunctions,
which can lead to user injury or property damage. Please contact Horizon
Hobby or an authorized retailer with compatibility questions.
InstructIon Manual
|
BedIenungsanleItung
|
Manuel d’utIlIsatIon
|
Manuale dI IstruzIonI (dYn4103)
Multi-Chemistry
AC/DC Charger

Included Items
JST_XH Balance adapter
BananaplugtoEC3
™
battery connector
ACpowercord(oneregion-US,EU,AUorUK)
OPTIONAL ACCESSORIES
DYN4011-DCPowerCord:DYN4103
DYN5031-InsulatedChargeAdapter,BananatoEC3Device
DYN5032-BalancingAdapterBoard
DYN5033-TemperatureSensor:DYN4103,DYN4300
Minimum computer requirements for use of included software: Microsoft
®
Windows XP
®
, Windows 7
®
orWindowsVista
®
operatingsystem,Compactdisk
(CD)readercapableofreadingamini-CDandUSB2.0port.
FEATURES
• Built-inLi-PoVoltageChecker
• Fourhigh-intensityLEDutilitylights
• 1AUSBchargeportcompatiblewithiPhone
®
, iPod
®
or similar products
• Space-savingverticaldesignwithcase-mountedstand
• 100–240VAC(50/60Hz)or11–18VDCinputvoltage
• Li-Ion/Li-Po/Li-Febatterycellcountof1to6seriescells
• Ni-Cd/Ni-MHbatterycellcountof1to15cells
• Pbbatteryvoltageof2to24V
• Built-in10Wdischarger
• Built-inbalancecircuit
• Short-circuit,over-current,reversepolarity,lowinputvoltageand
over-temperature protection
• StorageandFastChargemodes
• Userbatterydata,storeandloadupto10batteryproles
• 2x16backlit,blueLCD
• Insulated,colorcoded,bananajack,poweroutputterminals(Red=Positive(+),
Black=CommonorNegative(–))
• Internalcoolingfanwithgrillcover
• Operatingtemperaturerangeof0°Cto+50°C
• MeetsIP33CW,IK07environmentalspecs
• Ruggedindustrialplasticcase
SPECIFICATIONS
ACInputVoltage 100–240VAC(50/60Hz),65W(Max)
DCInputVoltage 11–18VDC55W(Max)
Output Max.Voltage25.2V,Max.ChargePower50W
ChargeCurrent 0.10to6.0A(in0.1Aincrements/50Wmaximum)
DischargeCurrent 0.10to2.0A(in0.1Aincrements/10Wmaximum)
Operating temperature 0°Cto+50°C
BalanceCurrentDrain 300mApercell
ChargingMode Peak(Ni-Cd/Ni-MH);CC/CV(Li-Po/Li-Ion/Li-Fe/Pb)
GETTING STARTED
CAUTION:NeverconnecttheACandDCinputcordstoanactivepower
source at the same time. This will void the warranty, cause product
damage and possibly injure the user.
When Using an External DC Power Source:
1.ConnecttheDCpowercordtothechargerDCpowerinputport.
2.ConnecttheDCalligatorclipstotheDCpowersource.
NOTICE: Always connect cable polarities correctly.
NOTICE: Alwaysconsult12VbatterycollateralmaterialsorHorizonHobby
beforeusingwithsourcesotherthanastandardACwalloutlet.
When Using External AC Power Source:
1.ConnecttheACpowercordtothechargerACpowerinputport.
2.ConnecttheACpowercordtotheACpowersource.
3.WhenthechargerispoweredON,amessagewillappearontheLCDscreen.
CAUTION: Always power ON the charger before connecting a battery, or
damage to the charger and the battery can result.
1.Connectthechargertothepowersupply.
2.Makeprogramselectionsinthechargerforbatterycharging.
3.Connectthechargeradapterstothecharger.
4.Connectthebatterytothechargeradapters(connectthemainchargingcon-
nectorsbeforeconnectingthecell-balancingconnectors,whereused).
5. Start battery charging.
Power Output
A.Red(+)
B.Black(–)
C. TemperatureProbeConnection
D. BalanceCircuitAdapterBoardConnector
E. UtilityLightON/OFFKey
F. –(Decrease)Key
G. ModeKey
H. EnterKey
I. +(Increase)Key
J. ReadBatteryVoltageKey
K. DischargeBatteryKey
L. BatteryVoltageIndicator
M.LCDScreen
N. LEDUtilityLights(x2)
O. 1AUSBChargePort
P. 1–6SLi-PoBatteryVoltageCheckerPort
Q. USBCommunicationsPort
R. DCPowerInputPort
S. ACPowerInputPort
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAMMING QUICK GUIDE
PresstheModekey(G)togettothe9mainmenuscreensfromanysubmenuscreen.
PresstheEnterkey(H)togettothesubmenusforadjustingoperatingparameters,tosavevaluechanges,ortostartchosenbatterychargingactions.
Pressthe–(F)or+(I)keystochangebetweensubmenuscreensortochangescreenvalues.
JST_XH ADAPTER
2S 3S 4S 6S5S
Not to scale.
Not all wiring shown.
Not all connectors shown.
OPERATING YOUR CHARGER
1
SELF TEST AND PROGRAM SELECT SCREENS
Press the Mode keyuntilyoureachthe9mainmenuscreens,thenusethe+
or – keystolocatethePROGRAMSELECTLiFeBATTscreen.PresstheEnter key
toselectLiFe.
Press the + or – keystogotooneofthecontrolscreens(BALANCE,CHARGE,
FASTCHG,STORAGEorDISCHARGE)todowhatyourbatteryneeds.
Correctlyconnectyourlithiumbatterytothecharger(chargingconnectorrstand
balancingconnectorsecond).PresstheEnter key and adjust the charging
parameters as needed. Press and hold the Enter key(approximately3seconds)
untilthescreenchangestostartthebatterycheck/chargesequence.
R: 3SER S:3SER
CONFIRM (ENTER)
A
When the charge cycle starts, the
charger compares the battery to the
charger settings. The screen will show
the battery and your settings
information.IftheinformationafterR:(charger)andS:(settings)(A) does not match,
press the Mode key and change the lithium battery charging parameters as
needed. If the R: information matches S:, press the Enter key to confirm. After
conrmation,chargingstartsandinformationwillshowontheLCDscreen
(informationmayvary).
LI 3S 2.0A 12.59V
BAL 022:43 01082
F E
B C D
A
A. ALi-Febatterypackis
balance charging
B. Batterypackhas3cellsin
series
C. Chargingrateis2.0A(2000mAh)
D. Voltagebeingappliedtothebatteryiscurrently12.59V
E. Presentchargelevelofthebatteryis1082mAh
F. Timeelapsedsincethechargeprocessstartedis22:43(22minutesand43
seconds)
During charging, the – key can be pressed to show several parameter messages
ontheLCDscreen,including:EndVoltage,InputPowerVoltage,External&Internal
Temperature,TemperatureCutoff,SafetyTimerStatusandCapacityCutoff.
Press the + key to see charge voltages for each cell and Enter to return to the
ChargeMonitorscreen.Thechargersignalswhenthecharging(ordischarging)
processiscomplete(ifBuzzerissettoON).
CAUTION:TheLi-FeprogrammenusaretobeusedONLYforthe
charginganddischargingofLi-Febatterypacks.Thechargingofother
battery types using these programs will result in damage to the battery or
charger.
CAUTION:Usingachargeratethatisnotcompatiblewiththebattery
capacities may result in damage or malfunction of the charger or
batteries.
3
LI-FE BALANCE CHARGING
When the charger is powered ON, there is a series of self tests and the screen will
show the charger brand name and model number.
DYNAMITE
DYN4103
After the self tests, the charger will show another screen. The information on this
screen will vary but will look smilar to this:
LiPo BALANCE
2.0A 7.4V(2S)
From any screen, press the Mode keytogobacktothe9mainmenuscreens.
2
LI-FE BATTERIES
Press the Mode key to return to the main menu, then press the + or – key until
youseethePROGRAMSELECTLiFeBATTscreen.PresstheEnter key to go into
this menu.
Press the + or – keytogototheLiFeBALANCEscreenandsetcharging
parameters. The charging amperage (A) canbesetbetween0.1and6.0A.Voltage
(B) isdependentonthenumberofcellsinseries.Forexample,withLi-Febatteries
thesevaluescanbefrom3.3V(for1Sbatteries)to19.8V(for6Sbatteries).
LiFe BALANCE
5.5A 19.8V(6S)
A B C
CAUTION: Always ensure you plug your battery’s balancing lead into the
correct port on your charger.
To select values other than existing parameters:
• PresstheEnter key so the charge current value (A) flashes
• Pressthe+ or – keytoINCREASEorDECREASEthechargecurrentvalue
• PresstheEnter key to save the value and the pack voltage value (B) flashes
• Pressthe+ or – keytoINCREASEorDECREASEthepackvoltage(and#ofcells
in series (C))
• PresstheEnter key to save the pack voltage value
If no parameters are flashing, you can press the + or – key to select another
programsuchasCHARGE,FASTCHG,STORAGEorDISCHARGE.
To start charging, press and hold the Enter keyfor3seconds.
4
LI-FE CHARGING
Press the Mode key to return to the main menu, then press the + or – key until
youseethePROGRAMSELECTLiFeBATTscreen.PresstheEnter key to go into
this menu.
Press the + or – keytogototheLiFeCHARGEscreenandsetcharging
parameters. The charging amperage (A) canbesetbetween0.1and6.0A.Voltage
(B) isdependentonthenumberofcellsinseries.Forexample,withLi-Febatteries
thesevaluescanbefrom3.3V(for1Sbatteries)to19.8V(for6Sbatteries).
LiFe CHARGE
4.6A 19.8V(6S)
A B C
To select values other than existing parameters:
• PresstheEnter key so the charge current value (A) flashes
• Pressthe+ or – keytoINCREASEorDECREASEthechargecurrentvalue
• PresstheEnter key to save the value and the pack voltage value (B) flashes
• Pressthe+ or – keytoINCREASEorDECREASEthepackvoltage(and#ofcells
in series (C))
• PresstheEnter key to save the pack voltage value
If no parameters are flashing, you can press the + or – key to select another
programsuchasBALANCE,FASTCHG,STORAGEorDISCHARGE.
To start charging, press and hold the Enter keyfor3seconds.
CAUTION: If at any time during the charge process the battery pack becomes
hot or begins to puff, disconnect the battery immediately and discontinue the
charge process as batteries can cause fire, collateral damage and injuries.
5
LI-FE FAST CHARGING
Press the Mode key to return to the main menu, then press the + or – key until
youseethePROGRAMSELECTLiFeBATTscreen.PresstheEnter key to go into
this menu.
Press the + or – keytogototheLiFeFASTCHGscreenandsetchargingparam-
eters. The charging amperage (A) canbesetbetween0.1and6.0A.Voltage(B) is
dependentonthenumberofcellsinseries.Forexample,withLi-Febatteriesthese
valuescanbefrom3.3V(for1Sbatteries)to19.8V(for6Sbatteries).
NeartheendofastandardchargingcyclethechargerswitchesfromConstantCur-
rent(CC)modetoConstantVoltage(CV)modetoslowly“topoff”thecurrentinthe
battery pack as close as possible to the maximum capacity.
InFastCharge,theCVmodeiseliminatedinordertogreatlyshortenthecharging
time;however,thenalcapacityofthebatterywillbelessthanwhatyouwouldget
using the standard charge method.
LiFe FAST CHG
0.1A 19.8V(6S)
A B C
To select values other than existing parameters:
• PresstheEnter key so the charge current value (A) flashes
• Pressthe+ or – keytoINCREASEorDECREASEthechargecurrentvalue
• PresstheEnter key to save the value and the pack voltage value (B) flashes
• Pressthe+ or – keytoINCREASEorDECREASEthepackvoltage(and#ofcells
in series (C))
• PresstheEnter key to save the pack voltage value
If no parameters are flashing, you can press the + or – key to select another
programsuchasCHARGE,BALANCE,STORAGEorDISCHARGE.
To start charging, press and hold the Enter keyfor3seconds.
6
LI-FE STORAGE CHARGING
Press the Mode key to return to the main menu, then press the + or – key until
youseethePROGRAMSELECTLiFeBATTscreen.PresstheEnter key to go into
this menu.
Press the + or – keytogototheLiFeSTORAGEscreenandsetchargingparam-
eters. The charging amperage (A) canbesetbetween0.1and6.0A.Voltage(B) is
dependentonthenumberofcellsinseries.Forexample,withLi-Febatteriesthese
valuescanbefrom3.3V(for1Sbatteries)to19.8V(for6Sbatteries).
Ifyoudon’tplanonusingyourbatteryforalongtime,itisbesttocharge(or
discharge)thebatterytoitsoptimalstoragevoltageandcapacity.
LiFe STORAGE
2.5A 19.8V(6S)
A B C
To select values other than existing parameters:
• PresstheEnter key so the charge current value (A) flashes
• Pressthe+ or – keytoINCREASEorDECREASEthechargecurrentvalue
• PresstheEnter key to save the value and the pack voltage value (B) flashes
• Pressthe+ or – keytoINCREASEorDECREASEthepackvoltage(and#ofcells
in series (C))
• PresstheEnter key to save the pack voltage value
If no parameters are flashing, you can press the + or – key to select another
programsuchasCHARGE,BALANCE,FASTCHGorDISCHARGE.
To start charging, press and hold the Enter keyfor3seconds.
7
LI-FE DISCHARGE
Press the Mode key to return to the main menu, then press the + or – key until
youseethePROGRAMSELECTLiFeBATTscreen.PresstheEnter key to go into
this menu.
Press the + or – keytogototheLiFeDISCHARGEscreenandsetdischargepa-
rameters. The discharging amperage (A)canbesetbetween0.1and2.0A.Voltage
(B)isdependentonthenumberofcellsinseries.Forexample,withLi-Febatteries
thesevaluescanbefrom3.3V(for1Sbatteries)to19.8V(for6Sbatteries).
A battery pack’s capacity can be verified by discharging the pack to its minimum
voltage level and measuring the current as the pack is discharged.
LiFe DISCHARGE
2.0A 19.8V(6S)
A B C
To select values other than existing parameters:
• PresstheEnter key so the discharge current value (A) flashes
• Pressthe+ or – keytoINCREASEorDECREASEthedischargecurrentvalue
• PresstheEnter key to save the value and the pack voltage value (B) flashes
• Pressthe+ or – keytoINCREASEorDECREASEthepackvoltage(and#ofcells
in series (C))
• PresstheEnter key to save the pack voltage value
If no parameters are flashing, you can press the + or – key to select another
programsuchasCHARGE,BALANCE,FASTCHGorSTORAGE.
To start discharging, press and hold the Enter keyfor3seconds.
8
LI-IO BATTERIES
Press the Mode keyuntilyoureachthe9mainmenuscreens,thenusethe+
or – keystolocatethePROGRAMSELECTLiIoBATTscreen.PresstheEnter key
toselectLiIo.
Press the + or – keystogotooneofthecontrolscreens(BALANCE,CHARGE,
FASTCHG,STORAGEorDISCHARGE)todowhatyourbatteryneeds.
Correctlyconnectyourlithiumbatterytothecharger(chargingconnectorrstand
balancingconnectorsecond).PresstheEnter key and adjust the charging
parameters as needed. Press and hold the Enter key(approximately3seconds)
untilthescreenchangestostartthebatterycheck/chargesequence.
R: 3SER S:3SER
CONFIRM (ENTER)
A
When the charge cycle starts, the
charger compares the battery to the
charger settings. The screen will show
the battery and your settings
information.IftheinformationafterR:(charger)andS:(settings)(A) does not match,
press the Mode key and change the lithium battery charging parameters as
needed. If the R: information matches S:, press the Enter key to confirm.
Afterconrmation,chargingstartsandinformationwillshowontheLCDscreen
(informationmayvary).
LI 3S 2.0A 12.59V
BAL 022:43 01082
F E
B C D
A
A. ALi-Iobatterypackisbalance
charging
B. Batterypackhas3cellsin
series
C. Chargingrateis2.0A(2000mAh)
D. Voltagebeingappliedtothebatteryiscurrently12.59V
E. Presentchargelevelofthebatteryis1082mAh
F. Timeelapsedsincethechargeprocessstartedis22:43
During charging, the – key can be pressed to show several parameter messages
ontheLCDscreen,including:EndVoltage,InputPowerVoltage,External&Internal
Temperature,TemperatureCutoff,SafetyTimerStatusandCapacityCutoff.
Press the + key to see charge voltages for each cell and Enter to return to the
ChargeMonitorscreen.Thechargersignalswhenthecharging(ordischarging)
processiscomplete(ifBuzzerissettoON).
CAUTION:TheLi-IoprogrammenusaretobeusedONLYforthecharging
anddischargingofLi-Iobatterypacks.Thechargingofotherbatterytypes
using these programs will result in damage to the battery or charger.
CAUTION:Usingachargeratethatisnotcompatiblewiththebattery
capacities may result in damage or malfunction of the charger or
batteries.
9
LI-IO BALANCE CHARGING
Press the Mode key to return to the main menu, then press the + or – key until
youseethePROGRAMSELECTLiIoBATTscreen.PresstheEnter key to go into
this menu.
Press the + or – keytogototheLiIoBALANCEscreenandsetchargingparam-
eters. The charging amperage (A) canbesetbetween0.1and6.0A.Voltage(B) is
dependentonthenumberofcellsinseries.Forexample,withLi-Iobatteriesthese
valuescanbefrom3.6V(for1Sbatteries)to21.6V(for6Sbatteries).
LiIo BALANCE
5.5A 21.6V(6S)
A B C
CAUTION: Always ensure you plug your battery’s balancing lead into the
correct port on your charger.
To select values other than existing parameters:
• PresstheEnter key so the charge current value (A) flashes
• Pressthe+ or – keytoINCREASEorDECREASEthechargecurrentvalue
• PresstheEnter key to save the value and the pack voltage value (B) flashes
• Pressthe+ or – keytoINCREASEorDECREASEthepackvoltage(and#ofcells
in series (C))
• PresstheEnter key to save the pack voltage value
If no parameters are flashing, you can press the + or – key to select another
programsuchasCHARGE,FASTCHG,STORAGEorDISCHARGE.
To start charging, press and hold the Enter keyfor3seconds.
10
LI-IO CHARGING
Press the Mode key to return to the main menu, then press the + or – key until
youseethePROGRAMSELECTLiIoBATTscreen.PresstheEnter key to go into
this menu.
Press the + or – keytogototheLiIoCHARGEscreenandsetchargingparameters.
The charging amperage (A) canbesetbetween0.1and6.0A.Voltage(B) is depen-
dentonthenumberofcellsinseries.Forexample,withLi-Iobatteriesthesevalues
canbefrom3.6V(for1Sbatteries)to21.6V(for6Sbatteries).
LiIo CHARGE
4.6A 21.6V(6S)
A B C
To select values other than existing parameters:
• PresstheEnter key so the charge current value (A) flashes
• Pressthe+ or – keytoINCREASEorDECREASEthechargecurrentvalue
• PresstheEnter key to save the value and the pack voltage value (B) flashes
• Pressthe+ or – keytoINCREASEorDECREASEthepackvoltage(and#ofcells
in series (C))
• PresstheEnter key to save the pack voltage value
If no parameters are flashing, you can press the + or – key to select another
programsuchasBALANCE,FASTCHG,STORAGEorDISCHARGE.
To start charging, press and hold the Enter keyfor3seconds.
CAUTION: If at any time during the charge process the battery pack becomes
hot or begins to puff, disconnect the battery immediately and discontinue the
charge process as batteries can cause fire, collateral damage and injuries.
11
LI-IO FAST CHARGING
Press the Mode key to return to the main menu, then press the + or – key until
youseethePROGRAMSELECTLiIoBATTscreen.PresstheEnter key to go into
this menu.
Press the + or – keytogototheLiIoFASTCHGscreenandsetchargingparam-
eters. The charging amperage (A) canbesetbetween0.1and6.0A.Voltage(B) is
dependentonthenumberofcellsinseries.Forexample,withLi-Iobatteriesthese
valuescanbefrom3.6V(for1Sbatteries)to21.6V(for6Sbatteries).
NeartheendofastandardchargingcyclethechargerswitchesfromConstantCur-
rent(CC)modetoConstantVoltage(CV)modetoslowly“topoff”thecurrentinthe
battery pack as close as possible to the maximum capacity.
InFastCharge,theCVmodeiseliminatedinordertogreatlyshortenthecharging
time;however,thenalcapacityofthebatterywillbelessthanwhatyouwouldget
using the standard charge method.
LiIo FAST CHG
5.0A 21.6V(6S)
A B C
To select values other than existing parameters:
• PresstheEnter key so the charge current value (A) flashes
• Pressthe+ or – keytoINCREASEorDECREASEthechargecurrentvalue
• PresstheEnter key to save the value and the pack voltage value (B) flashes
• Pressthe+ or – keytoINCREASEorDECREASEthepackvoltage(and#ofcells
in series (C))
• PresstheEnter key to save the pack voltage value
If no parameters are flashing, you can press the + or – key to select another
programsuchasCHARGE,BALANCE,STORAGEorDISCHARGE.
To start charging, press and hold the Enter keyfor3seconds.
12
LI-IO STORAGE CHARGING
Press the Mode key to return to the main menu, then press the + or – key until
youseethePROGRAMSELECTLiIoBATTscreen.PresstheEnter key to go into
this menu.
Press the + or – keytogototheLiIoSTORAGEscreenandsetchargingparam-
eters. The charging amperage (A) canbesetbetween0.1and6.0A.Voltage(B) is
dependentonthenumberofcellsinseries.Forexample,withLi-Iobatteriesthese
valuescanbefrom3.6V(for1Sbatteries)to21.6V(for6Sbatteries).
Ifyoudon’tplanonusingyourbatteryforalongtime,itisbesttocharge(or
discharge)thebatterytoitsoptimalstoragevoltageandcapacity.
LiIo STORAGE
2.5A 21.6V(6S)
A B C
To select values other than existing parameters:
• PresstheEnter key so the charge current value (A) flashes
• Pressthe+ or – keytoINCREASEorDECREASEthechargecurrentvalue
• PresstheEnter key to save the value and the pack voltage value (B) flashes
• Pressthe+ or – keytoINCREASEorDECREASEthepackvoltage(and#ofcells
in series (C))
• PresstheEnter key to save the pack voltage value
If no parameters are flashing, you can press the + or – key to select another
programsuchasCHARGE,BALANCE,FASTCHGorDISCHARGE.
To start charging, press and hold the Enter keyfor3seconds.
1 SELFTESTANDPROGRAMSELECTSCREENS
LI-FE
2 LI-FEBATTERIES
3 LI-FEBALANCECHARGING
4 LI-FECHARGING
5 LI-FEFASTCHARGING
6 LI-FESTORAGECHARGING
7 LI-FEDISCHARGE
LI-IO
8 LI-IOBATTERIES
9 LI-IOBALANCECHARGING
10 LI-IOCHARGING
11 LI-IOFASTCHARGING
12 LI-IOSTORAGECHARGING
13 LI-IODISCHARGE
LI-PO
14 LI-POBATTERIES
15 LI-POBALANCECHARGING
16 LI-POCHARGING
17 LI-POFASTCHARGING
18 LI-POSTORAGECHARGING
19 LI-PODISCHARGE
NI-MH
20 NI-MH BATTERIES
21 NI-MHCHARGING
22 NI-MHAUTOCHARGING
23 NI-MHDISCHARGE
24 NI-MHRE-PEAKCHARGING
25 NI-MHCYCLECHARGING
NI-CD
26 NI-CDBATTERIES
27 NI-CDCHARGING
28 NI-CDAUTOCHARGING
29 NI-CDDISCHARGE
30 NI-CDRE-PEAKCHARGING
31 NI-CDCYCLECHARGING
PB
32 PB BATTERIES
33 PBCHARGING
34 PBDISCHARGE
PROGRAMMING AND OPERATIONS
35 BATTERY MEMORY
36 SYSTEM SET
a REST TIME
b SAFETY TIMER
c CAPACITYCUTOFF
d KEYBEEP/BUZZER
e INPUTPOWERLOWCUTOFF
f EXTERNALANDINTERNALTEMPERATURES
g RESETFACTORYSETTINGS
h VERSION
37 LIBATTERYVOLTAGECHECKEROPERATION-
USINGTHEBALANCEADAPTERPORT
38 UTILITYLIGHTSOPERATION
39 REAR STAND OPERATION
40 LI-POVOLTAGECHECKEROPERATION
41 USBACCESSORYCHARGEROPERATION
(COMPATIBLEWITHiPhone AND iPodDEVICES)
42 TROUBLESHOOTINGGUIDE
Press the Mode key to return to the main menu, then press the + or – key until
youseethePROGRAMSELECTLiIoBATTscreen.PresstheEnter key to go into
this menu.
Press the + or – keytogototheLiIoDISCHARGEscreenandsetdischargeparam-
eters. The discharging amperage (A) canbesetbetween0.1and2.0A.Voltage(B)
isdependentonthenumberofcellsinseries.Forexample,withLi-Iobatteriesthese
valuescanbefrom3.6V(for1Sbatteries)to21.6V(for6Sbatteries).
A battery pack’s capacity can be verified by discharging the pack to its minimum
voltage level and measuring the current as the pack is discharged.
LiIo DISCHARGE
2.0A 21.6V(6S)
A B C
To select values other than existing parameters:
• PresstheEnter key so the discharge current value (A) flashes
• Pressthe+ or – keytoINCREASEorDECREASEthedischargecurrentvalue
• PresstheEnter key to save the value and the pack voltage value (B) flashes
• Pressthe+ or – keytoINCREASEorDECREASEthepackvoltage(and#ofcells
in series (C))
• PresstheEnter key to save the pack voltage value
If no parameters are flashing, you can press the + or – key to select another
programsuchasCHARGE,BALANCE,FASTCHGorSTORAGE.
To start discharging, press and hold the Enter keyfor3seconds.
13
LI-IO DISCHARGE
14
LI-PO BATTERIES
Press the Mode keyuntilyoureachthe9mainmenuscreens,thenusethe+
or – keystolocatethePROGRAMSELECTLiPoBATTscreen.PresstheEnter key
toselectLiPo.
Press the + or – keystogotooneofthecontrolscreens(BALANCE,CHARGE,
FASTCHG,STORAGEorDISCHARGE)todowhatyourbatteryneeds.
Correctlyconnectyourlithiumbatterytothecharger(chargingconnectorrstand
balancingconnectorsecond).PresstheEnter key and adjust the charging
parameters as needed. Press and hold the Enter key(approximately3seconds)
untilthescreenchangestostartthebatterycheck/chargesequence.
R: 3SER S:3SER
CONFIRM (ENTER)
A
When the charge cycle starts, the
charger compares the battery to the
charger settings. The screen will show
the battery and your settings
information.IftheinformationafterR:(charger)andS:(settings)(A) does not match,
press the Mode key and change the lithium battery charging parameters as
needed. If the R: information matches S:, press the Enter key to confirm.
Afterconrmation,chargingstartsandinformationwillshowontheLCDscreen
(informationmayvary).
LI 3S 2.0A 12.59V
BAL 022:43 01082
F E
B C D
A
A. ALi-Pobatterypackis
balance charging
B. Batterypackhas3cellsin
series
C. Chargingrateis2.0A(2000mAh)
D. Voltagebeingappliedtothebatteryiscurrently12.59V
E. Presentchargelevelofthebatteryis1082mAh
F. Timeelapsedsincethechargeprocessstartedis22:43
During charging, the – key can be pressed to show several parameter messages
ontheLCDscreen,including:EndVoltage,InputPowerVoltage,External&Internal
Temperature,TemperatureCutoff,SafetyTimerStatusandCapacityCutoff.
Press the + key to see charge voltages for each cell and Enter to return to the
ChargeMonitorscreen.Thechargersignalswhenthecharging(ordischarging)
processiscomplete(ifBuzzerissettoON).
CAUTION:TheLi-PoprogrammenusaretobeusedONLYforthe
charginganddischargingofLi-Pobatterypacks.Thechargingofother
battery types using these programs will result in damage to the battery or
charger.
CAUTION:Usingachargeratethatisnotcompatiblewiththebattery
capacities may result in damage or malfunction of the charger or
batteries.
15
LI-PO BALANCE CHARGING
Press the Mode key to return to the main menu, then press the + or – key until
youseethePROGRAMSELECTLiPoBATTscreen.PresstheEnter key to go into
this menu.
Press the + or – keytogototheLiPoBALANCEscreenandsetchargingparam-
eters. The charging amperage (A) canbesetbetween0.1and6.0A.Voltage(B) is
dependentonthenumberofcellsinseries.Forexample,withLi-Pobatteriesthese
valuescanbefrom3.7V(for1Sbatteries)to22.2V(for6Sbatteries).
LiPo BALANCE
5.5A 22.2V(6S)
A B C
CAUTION: Always ensure you plug your battery’s balancing lead into the
correct port on your charger.
To select values other than existing parameters:
• PresstheEnter key so the charge current value (A) flashes
• Pressthe+ or – keytoINCREASEorDECREASEthechargecurrentvalue
• PresstheEnter key to save the value and the pack voltage value (B) flashes
• Pressthe+ or – keytoINCREASEorDECREASEthepackvoltage(and#ofcells
in series (C))
• PresstheEnter key to save the pack voltage value
If no parameters are flashing, you can press the + or – key to select another
programsuchasCHARGE,FASTCHG,STORAGEorDISCHARGE.
To start charging, press and hold the Enter keyfor3seconds.
CONTENTS
16
LI-PO CHARGING
Press the Mode key to return to the main menu, then press the + or – key until
youseethePROGRAMSELECTLiPoBATTscreen.PresstheEnter key to go into
this menu.
Press the + or – keytogototheLiPoCHARGEscreenandsetchargingparam-
eters. The charging amperage (A) canbesetbetween0.1and6.0A.Voltage(B) is
dependentonthenumberofcellsinseries.Forexample,withLi-Pobatteriesthese
valuescanbefrom3.7V(for1Sbatteries)to22.2V(for6Sbatteries).
LiPo CHARGE
4.6A 22.2V(6S)
A B C
To select values other than existing parameters:
• PresstheEnter key so the charge current value (A) flashes
• Pressthe+ or – keytoINCREASEorDECREASEthechargecurrentvalue
• PresstheEnter key to save the value and the pack voltage value (B) flashes
• Pressthe+ or – keytoINCREASEorDECREASEthepackvoltage(and#ofcells
in series (C))
• PresstheEnter key to save the pack voltage value
If no parameters are flashing, you can press the + or – key to select another
programsuchasBALANCE,FASTCHG,STORAGEorDISCHARGE.
To start charging, press and hold the Enter keyfor3seconds.
CAUTION: If at any time during the charge process the battery pack becomes
hot or begins to puff, disconnect the battery immediately and discontinue the
charge process as batteries can cause fire, collateral damage and injuries.
LITHIUM BATTERIES (Li-Fe)
LITHIUM BATTERIES (Li-Po)
Pb BATTERIES
Ni-Cd BATTERIES
Ni-MH BATTERIES
LITHIUM BATTERIES (Li-Ion)
BATTERY MEMORY
LITHIUM BATTERY METER
SYSTEM SET