User Manual

4
Included Items
AC Power Cord
(2) Charge Adapter: Banana to EC3™ Device (DYNC0072)
(2) Bare charge leads
(2) Balancing Adapter Board: XH (DYN5032)
Optional Items
Temperature Sensor (DYN5033)
Dynamite
®
LiPo Charge Bag: small (DYN1400), large (DYN1405)
Charge Adapter: Banana to Deans (DYNC0056)
Charge Adapter: Banana to XT60 (DYNC0143)
DC Power Cord: Alligator to XT60 (DYNC1108)
CONTROL LAYOUT
Specifi cations
AC Power Distribution
Channels A and B: 100 watts total
Power Distribution Adjustable Range
Channels A and B: 0 – 100 watts (AC only)
Charge Current
Channels A and B: 0.1 – 10 Amps
Peak Charge Voltage
LiPo: 4.18 – 4.25V/cell LiHV: 4.25 – 4.35V/cell LiFe: 3.58 – 3.7V/cell LiIon: 4.08 – 4.2V/cell
NiMH/NiCd: Uses delta peak detection
Discharge Wattage
10 Watts per channel
Discharge Current
0.1 – 5 Amps per channel
Discharge Cut-off Voltages
LiPo: 3.0 – 3.3V/cell LiHV: 3.1 – 3.4V/cell LiFe: 2.6 – 2.9V/cell LiIon: 2.9 – 3.2V/cell
NiMH/NiCd: 0.1 – 1.1V/cell
Input Voltage
100 – 240V AC (50 – 60Hz); 11 – 18V DC
Charging Capability
1 – 6S Li-Po/Li-Ion/Li-Fe; 1 – 15C Ni-Cd/Ni-MH; 2 – 20V Pb
Battery Capacities
100 – 50000 mAh
Charge Current
0.1A – 10A x 2 (in 0.1A Increments/100W max AC, 200W DC)
Discharge Current
0.10A – 5.0A x 2 (in 0.1A Increments/10W max)
Balance Current
200mA max per cell
Operating Temperature
0ºC to + 40ºC
Charging Mode
Ni-Cd/Ni-MH: Peak; Li-Po/Li-Ion/Li-Fe/Pb: CC/CV
Protection
Short-circuit, over-current, reverse polarity, low input voltage, over-temperature
A. DC Power Cable (optional, not included)
B. DC Power Input Port
C. AC Power Input Cable
D. AC Power Input Port
E. LCD Screen
F. Charge Port Selection Button
G. Charge Port A Positive Power Output
H. Charge Port A Negative Power Output
I. Charge Port A Balance Connector
J. Balance Board
K. BATT/PROG Stop
L. DEC (decrease)
M. INC (increase)
N. ENTER Start
O. Charge Port B Negative Power Output
P. Charge Port B Positive Power Output
Q. Charge Port B Balance Board Connector
R. Charge Port B Temperature Sensor Port
S. PC Link
T. 5V 2.1A USB Power supply
U. Charge Port A Temperature Sensor Port
V. Battery Adapter Cable
Standard Battery Parameters
Battery Type LiPo LiIon LiFe LiHV NiCd NiMH PB
Nominal Voltage (per cell) 3.7V 3.6V 3.3V 3.7V 1.2V 1.2V 2.0V
Max Charge Voltage (per cell) 4.2V 4.1V 3.6V 4.35V 1.5V 1.5V 2.4V
Storage Voltage (per cell) 3.8V 3.7V 3.3V 3.85V n/a n/a n/a
Allowable Fast Charge Rate ≤1C ≤1C ≤4C ≤1C ≤1C ≤1C ≤0.4C
Minimum Discharge Voltage (per cell) 3.0V 2.9V 2.6V 3.1V 0.9V 0.9V 1.8V