User Manual

ManualsBrandsDynamite ManualsHobbyPassport Ultra Force 220W Touch Battery Charger

CAUTION: The nickel charge program menus are to be used ONLY for the charging and discharging of nickel battery packs. Charging other battery types using the nickel charge programs will

damage the battery or the charger.

1. Connect the banana plugs of the battery adapter cable to the Power Output Black (–)

and Power Output Red (+), making sure that the positive and negative connectors are not

reversed.

2. Connect the battery connector to the battery adapter cable.

3. Press the Left and Right Arrows on the LCD Touch Screen to scroll through the main menu

screens until you reach Program Select=Ni-MH/Ni-Cd.

Program select=NiMH

CHG DCHG

N i M H

CYCLE

4. Press CHG.

NiMH CHARGE

Capacity : 50mAh

Current : 0.1A

CHG Mode : Man

Press&Hold : CHARGE

BACK SELECT

5. Press a parameter to highlight that parameter.

6. Press the Up and Down Arrows to edit the parameter.

7. Press Select to save the parameter.

8. Once the parameters are at the desired settings, press and hold CHARGE.

9. The charger will check the battery and charger settings and charging will begin. The charger

will beep and display the following screen:

NiMH CHG 000:09S

Capacity : 2mAh

Current : 1.8A

Voltage : 7.98V

Resistance : ****mΩ

Peak Temp. : No sens

STOP Graph

10. Press the arrow in the top right of the LCD Touch Screen to see the rest of the Charging

information.

11. Press Graph to see the battery voltage graph. Press Back to return to the charging screen.

Data NiMH = Graph

8.03V 000:28S

BACK

12. Press STOP at any time to stop charging.

13. When charging is complete, the charger will sound a series of beeps and display the following

screen:

NiMH DONE 026:01S

Capacity : 671mAh

Current : 0.0A

Voltage : 9.25V

Resistance : 14mΩ

Peak Temp. : No sens

BACK Graph

14. Disconnect the battery from the charger.

Only Ni-MH is shown in the following three sections.

5 - NICKEL (NI-MH/NI-CD) CHARGING

6 - NICKEL DISCHARGING

1. Connect the banana plugs of the battery adapter cable to the Power Output Black (–)

and Power Output Red (+), making sure that the positive and negative connectors are not

reversed.

2. Connect the battery connector to the battery adapter cable.

3. Press the Left and Right Arrows on the LCD Touch Screen to scroll through the main menu

screens until you reach Program Select=Ni-MH/Ni-Cd.

Program select=NiMH

CHG DCHG

N i M H

CYCLE

4. Press DCHG.

NiMH DISCHARGE

End Volt : 0.10V

Capacity : 50mAh

Current : 0.1A

Press&Hold : DISCHRG

BACK SELECT

5. Press a parameter to highlight that parameter.

6. Press the Up and Down Arrows to edit the parameter.

7. Press Select to save the parameter.

8. Once the parameters are at the desired settings, press and hold DISCHRG.

9. The charger will check the battery and charger settings and discharging will begin. The charger will

beep and display the following screen:

NiMH DCHG 000:34S

Capacity : 16mAh

Current : 1.8A

Voltage : 8.43V

Resistance : ****mΩ

Peak Temp. : No sens

STOP Graph

10. Press the arrow in the top right of the LCD Touch Screen to see the rest of the Discharging

information.

11. Press Graph to see the battery voltage graph. Press Back to return to the discharging screen.

Data NiMH = Graph

8.39V 000:47S

BACK

12. Press STOP at any time to stop discharging.

13. When discharging is complete, the charger will sound a series of beeps and display the

following screen:

NiMH DONE 026:01S

Capacity : 671mAh

Current : 0.0A

Voltage : 9.25V

Resistance : 14mΩ

Peak Temp. : No sens

BACK Graph

14. Disconnect the battery from the charger.