User Manual

4
3 - LITHIUM DISCHARGING
1. Connect the banana plugs of the battery adapter cable to the Power Output Black (–) and
Power Output Red (+), making sure that the positive and negative connectors are not reversed.
2. Connect the JST_XH balance adapter to the Balance Circuit Adapter Board Connector.
3. Connect the battery connector to the battery adapter cable.
4. Connect the balance connector of the battery to the JST_XH balance adapter.
5. Press the Left and Right Arrows on the LCD Touch Screen to scroll through the main menu
screens until you reach Program Select=Li-Po/Li-Ion/Li-Fe.
Program select=LiPo
LiPo
CHG DCHG STOR
6. Press DCHG.
LiPo DISCHARGE
Pack.Volt. : 7.4V/2S
Capacity : 2250mAh
Current : 0.5A
End Cell Volt : 3.49V
Press&Hold : DISCHRG
BACK SELECT
7. Press a parameter to highlight that parameter.
8. Press the Up and Down Arrows to edit the parameter.
9. Press Select to save the parameter.
10. Once the parameters are at the desired settings, press and hold DISCHRG.
11. The charger will check the battery and charger settings and discharging will begin. The
charger will beep and display the following screen:
LiPo DCHG 000:30S
Capacity : 13mAh
Current : 1.4A
Voltage : 7.91V
Resistance : ****mΩ
Peak Temp. : No sens
STOP Unit Graph
12. Press the arrow in the top right of the LCD Touch Screen to see the rest of the Discharging
information.
13. Press Unit to see the voltages for each cell. Press Back to return to the discharging screen.
DATA LiPo–CELLS
1 > 3.97
2 > 3.98
3 > 0.00
4 > 0.00
5 > 0.00
6 > 0.00
BACK
14. Press Graph to see the battery voltage graph. Press Back to return to the discharging screen.
Data LiPo = Graph
7.91V 001:25S
BACK
15. Press STOP at any time to stop discharging.
16. When discharging is complete, the charger will sound a series of beeps and display the
following screen:
LiPo DONE 010:28S
Capacity : 169mAh
Current : 0.0A
Voltage : 8.00V
Resistance : ****mΩ
Peak Temp. : No sens
BACK Unit Graph
17. Disconnect the battery from the charger.
1. Connect the banana plugs of the battery adapter cable to the Power Output Black (–) and
Power Output Red (+), making sure that the positive and negative connectors are not reversed.
2. Connect the JST_XH balance adapter to the Balance Circuit Adapter Board Connector.
3. Connect the battery connector to the battery adapter cable.
4. Connect the balance connector of the battery to the JST_XH balance adapter.
5. Press the Left and Right Arrows on the LCD Touch Screen to scroll through the main menu
screens until you reach Program Select=Li-Po/Li-Ion/Li-Fe.
Program select=LiPo
LiPo
CHG DCHG STOR
6. Press STOR.
LiPo STORAGE
Pack.Volt. : 3.7V/1S
Capacity : 50mAh
Current : 0.1A
End Cell Volt : 3.70V
Press&Hold : STORE
BACK SELECT
7. Press a parameter to highlight that parameter.
8. Press the Up and Down Arrows to edit the parameter.
9. Press Select to save the parameter.
10. Once the parameters are at the desired settings, press and hold STORE.
11. The charger will check the battery and charger settings and storage charging will begin. The
charger will beep and display the following screen:
LiPo STORE 000:11S
Capacity : 4mAh
Current : 1.8A
Voltage : 7.87V
Resistance : ****mΩ
Peak Temp. : No sens
STOP Unit Graph
12. Press the arrow in the top right of the LCD Touch Screen to see the rest of the storage
Charging information.
13. Press Unit to see the voltages for each cell. Press Back to return to the storage charging screen.
DATA LiPo–CELLS
1 > 3.97
2 > 3.98
3 > 0.00
4 > 0.00
5 > 0.00
6 > 0.00
BACK
14. Press Graph to see the battery voltage graph. Press Back to return to the storage charging screen.
Data LiPo = Graph
8.03V 000:34S
BACK
15. Press STOP at any time to stop charging.
16. When charging is complete, the charger will sound a series of beeps and display the following
screen:
LiPo DONE 010:28S
Capacity : 169mAh
Current : 0.0A
Voltage : 8.00V
Resistance : ****mΩ
Peak Temp. : No sens
BACK Unit Graph
17. Disconnect the battery from the charger.
4 - LITHIUM STORAGE CHARGING