Passport Ultra AC/DC Charger Cycler Operation Manual www.DynamiteRC.
NOTICE: All instructions, warranties, and other collateral documents are subject to change at the sole discretion of Horizon Hobby, Inc. For up-to-date product literature, visit http://www.horizonhobby. com/Products/Default.aspx?ProdID=DYN4065 Meaning of Special Language: Introduction Thank you for purchasing the Dynamite® Passport™ Ultra AC/DC Peak Detection Charger/Cycler.
Input Power Connection NOTE: NEVER connect both AC and DC input power types to the charger simultaneously or damage to the charger may occur. AC Voltage DYN5003 Charge Adapt Tamiya Female: Losi Micro DYN5008 Charge Adapter Banana: EC5 Female Connect the 100–240 AC input power cord to the appropriate power receptacle. NOTICE: Always consult 12V battery collateral materials or Horizon Hobby before using with sources other than standard AC wall outlet.
Operating Instructions A. Press the MODE button to change from the NiMH Sensitivity main menu to the setting menu. Rotating D.Peak 3mV/Cell the dial in the main menu lists all options available for the battery chemistry shown on the screen. Rotating the dial while in the 3. Adjust Ni-MH Charge Sensitivity settings menu lists menus that allow changes The Ni-MH Sensitivity option allows the to the chargers functionality unrelated to the adjustment of the Ni-MH negative delta battery type.
Peak Voltage 9.07V 2. Battery Pack Peak Voltage Cycle Charge Delay 1min 8. Charge/Discharge Delay Time Input 13.01V System Temp 36°C 3. Input Voltage/System Temperature Message after Ni-MH Charging END 058 : 08 : 3188 Chg 0.01A 8.08V appears. Press the dial to select discharge current rate and cutoff voltage. Message during Ni-MH Discharging Press and hold the START button for 3 seconds to begin discharging. NOTE: Discharge voltage rates are per pack, not per cell.
complete. E. D/1 alternate flashing designates that the charger is in the cool down time period after discharging. Li-Ion, Li-Po and Li-Fe Charge Mode WARNING: Li-Po batteries can cause serious injury and fire if charged inappropriately. F. C/1 alternate flashing designates that the Always confirm the battery voltage and series charger is in the cool down time period after cell count is correct and never charge higher charging. than a 1C rate.
Li-Ion/Poly Charge Warning Message Li-Ion/Poly Balance Charge Mode ERR Batt Over Voltage Li-Poly Bal. Chg 4.0A 14.8V(4S) 1. Battery Over Voltage WARN Volt Select Err Message during Li-Ion/Poly Balance Charging Li4S 0000:01 0001 Bal 0.10A 15.18V Li-Ion/Poly Balance Charge Warning Message WARN Volt Select Err 1. Set Wrong Battery Voltage Balancer No Connect 2. Set Wrong Battery Voltage ERR Batt Low Voltage 3.
Pb Charge Mode Pb Charge 4.0A 12.0V Warning Information Capacity Cut Off ON 9900 mAh 4. Max Charge Capacity Suggested charge rate for PB charging is 0.3C (i.e. .3 x 5Ah=1.5A). Message during Pb Charging Pb 000:01 0001 Chg 0.58A 14.21V See the status by turning dial during the charge process. Select Voltage 14.7V 1. Selected Fast Charge Cutoff Voltage. The cutoff value is predetermined when selecting the 2V, 6V, or 12V setting before charging and is not adjustable once charging has begun. Input 13.
• Always keep batteries and charger away from any material that could be affected by heat (such as ceramic and tile), as they can get hot. Warranty Period Exclusive Warranty- Horizon Hobby, Inc., (Horizon) warranties that the Products purchased (the “Product”) will be free from defects in materials and workmanship for a • Always ensure program settings are correct to period of 5 years from the date of purchase by prevent battery damage or fire. the Purchaser.
Non-Warranty Repairs Should your repair not be covered by warranty the repair will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50% of the retail purchase cost. By submitting the item for repair you are agreeing to payment of the repair without notification. Repair estimates are available upon request.You must include this request with your repair. Non-warranty repair estimates will be billed a minimum of 1/2 hour of labor.
Distributed exclusively by Horizon Hobby, Inc. 4105 Fieldstone Road Champaign, IL 61822 Horizon Hobby UK Units 1-4 Ployters Rd Staple Tye Harlow, Essex CM18 7NS United Kingdom Horizon Hobby Deutschland GmbH Hamburger Strasse 10 25335 Elmshorn Germany www.horizonhobby.com ©2010 Horizon Hobby, Inc. 15245.
