User Manual

1/8 6-Pole 1800Kv Waterproof ESC/Motor Combo V2
Instruction Manual | Bedienungsanleitung | Manuel d’utilisation | Manuale di Istruzioni
(DYNS1800)
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-
date product literature, visit horizonhobby.com and click on the support tab for this product.
MEANING OF SPECIAL LANGUAGE
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious
injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury
OR create a high probability of superficial injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to
operate the product correctly can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability.
Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product
is not intended for use by children without direct adult supervision. Do not attempt disassembly, use with incompatible components or alter
product in any way without the approval of Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It
is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly
and avoid damage or serious injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
WATERPROOF COMPONENT
Your new Horizon Hobby
®
Dynamite
®
Fuze
™
ESC/Motor combination
has been designed and built to allow you to operate the product in
many “wet conditions,” including puddles, creeks, wet grass, snow
and even rain.
While waterproof, this component has not been designed to be
immersed in water for long periods of time and should NOT be
treated like a submarine. In addition, most metal parts, including
any screws and nuts, as well as the contacts in the electrical
cables, will be susceptible to corrosion if additional maintenance is
not performed after running in wet conditions.
To maximize the long-term performance of your ESC and to keep the
warranty intact, it should only be used as described in the “Usage
Conditions” section of this manual. Additionally, the procedures
described in the “Wet Conditions Maintenance” section must be
performed regularly if you choose to run in wet conditions. If you
are not willing to perform the additional care and maintenance
required, then you should not operate your vehicle in those
conditions.
CAUTION: Failure to exercise caution while using this
product and comply with the following precautions could
result in product malfunction and/or void the warranty.
GENERAL PRECAUTIONS
• Read through the wet conditions maintenance procedures and
make sure that you have all the tools you will need to properly
maintain your ESC.
• DonotoperateyourESCwhere it could come in contact with
salt water (ocean water or water on salt-covered roads),
contaminated or polluted water. Salt water is very conductive
and highly corrosive, so use caution.
USAGE CONDITIONS
Your ESC will operate successfully in any of the following,
individual-usage scenarios:
• 2hourscontinuousoperationindampgrassorvegetation.
• 2hourscontinuousoperationinheavyfog(95%humidity,
saturated air, condensing water).
• 1hourcontinuousoperationinlightrain(<0.10in/2.5mmper
hour).
• 15minutescontinuousoperationinheavyrain(>0.30in/7.6mm
per hour).
• 1hourcontinuousoperationinlightsleet(<0.10in/2.5mmper
hour).
• 1hourcontinuousoperationinlightsnow(<0.25in/6.35mmper
hour).
• 45minutescontinuousoperationinstandingorrunningfresh
water (the water level should always remain below the vehicle
frame), or constant splashing water, without any immersion of
waterproof component(s).
• 5minutescontinuousoperationinstandingorrunningfresh
water(thewaterlevelshouldneverrisehigherthan0.5in(about
10mm)abovethevehicleframe),constantsplashingwater,or
frequent, intermittent immersion of waterproof component(s).
• 1hourcontinuousoperationindampsand,dirt,mudorsnow
(the material level should always be below the vehicle frame),
constant splatter without any immersion or coverage of
waterproof component(s).
Furthermore, when appropriate maintenance procedures (as
described below) are performed promptly following exposure, the
ESC will remain best protected from corrosion or other long-term,
water-related damage.
WET CONDITIONS MAINTENANCE
• GentlyrinsethemudanddirtofftheESCwith a garden hose.
• Removethebatterypack(s)anddrythecontacts.
• Ifyouhaveanaircompressororacanofcompressedair
available, blow off the ESC to help remove any water that may
have gotten into small crevices or corners. Dry any water that
may be inside a recessed connector housing.
• LettheESCairdrybeforeyoustoreit.Watermaycontinueto
seep or evaporate out of tight areas for a few hours.
NOTICE: Never use a pressure washer to clean your vehicle.
NOTICE: This ESC is waterproofed for use in wet conditions.
Make sure the other components in your vehicle are
waterproof or water-resistant before driving in wet
conditions.
FEATURES
• CompatiblewithNi-Cd/Ni-MHandLi-Po/Li-Ionbatteries.
• Pre-wiredwithbullet-stylemotorconnectorsandauniversal
receiver plug that fits most popular radio systems
• 6-Polerotordesignforhightorque,powerandefciency
• BasicsetupandprogrammingthroughtheSETbutton
• EnhancedprogrammingisavailablewithoptionalDigitalProgram
Box(DYNS3005)
• Designedforon-roadandoff-roaduse
• High-precisionspeedandpowercontrol
• High-power,built-inBECsystemforstablereceiverandservo
power supply
• Forwardandreversefunction
• AdjustablesettingsintheESCfornecontrolofvehicleoperation
• Multipleprotectionsystems:batterylowvoltagecut-off,overheat-
ing, radio signal loss, stuck or locked motor or driveline
DESCRIPTIONS
1 Running Mode: Forward Only with Brake—Intended for competi-
tion use, this mode allows only forward and brake controls.
Forward/Reverse with Brake—This mode is the basic all-around
mode, allowing forward, reverse and brake controls. To engage
reverse while moving forward, apply the brake until the vehicle has
come to a complete stop, release brake, then apply the brake again.
While braking or in reverse, engaging the throttle will result in the
vehicle immediately accelerating forward.
Forward/Reverse—Intended for Rock Crawler use only. In this mode,
there is no brake, eliminating the delay between forward to reverse.
NOTICE: Do not use this mode with car types other than Rock
Crawlers as this mode can overload and/or damage the ESC.
2 Drag Brake Force: Adjusts the amount of brake automatically
applied when the throttle is returned to the neutral position. This
simulates the engine braking effect of a full-scale vehicle, allowing
improved turn-in and your vehicle’s general response to controls.
3 Low Voltage Cut-off: This function helps to prevent battery over-
discharge. The ESC continuously monitors the battery’s voltage. If the
voltagefallsbelowthevoltagethresholdfor2seconds,theoutput
power shuts off and the red LED flashes twice repeatedly.
The cutoff threshold calculation is based on individual Li-Po cell
voltage. For Ni-MH batteries, if the voltage battery pack is higher than
9.0V,itwillbeconsideredasa3-cellLi-Pobatterypack;Ifitislower
than9.0V,itwillbeconsideredasa2-cellLi-Pobatterypack.Example:
fora8.0VNi-MHbatterypackusedwitha2.6V/cellthreshold,it
willbeconsideredasa2-cellLi-Pobatterypackandthelow-voltage
cut-offthresholdwillbe5.2V(2.6x2=5.2).UsingtheoptionalDigital
ProgramBox(DYN3748),youcanadjustthecustomvaluesforthe
cutoff threshold. Unlike the preset values, custom cutoff values are for
the total battery voltage, not individual cell voltage.
4 Start Mode (Punch): Sets the initial throttle punch when the car
accelerates.Level1givesaverysoftinitialaccelerationandlevel
9givesaverystronginitialacceleration.Whenusinglevels7,8or
9,youmustusehigh-powerbatteries.Withlowpowerbatteries,
the battery could overload and result in poor performance or
unexpected results.
5 Max Brake Force: Adjusts the maximum braking force. A higher
value provides stronger braking, but can also cause the wheels to
lock, resulting in loss of control of the car.
6 Max Reverse Force: This parameter adjusts the maximum power
when travelling in reverse.
7 Initial Brake Force (minimum brake): Adjusts the minimum
amount of braking power when the brakes engage. The default value
is equal to the drag brake value. A high value can lock the wheels
when the brake is used.
8 Neutral Range: Adjusts the throttle sensitivity around the neutral
point. A higher value results in the throttle having to be moved more
for the vehicle to move forward, backward or brake.
9 Timing: Adjusts the motor drive current timing. More timing gives
more performance, but can lower efficiency and cause damage to the
motor and/or ESC by overload or overheating.
NOTICE: Always ensure the motor timing is set correctly.
Failure to set the motor timing correctly can result in result in
overheating and damage to the motor and ESC.
The Following Programmable Items require the optional
Digital ESC Program Box:
10 and 11 Available Items are subject to firmware updates to the
ESC and the optional digital program box.
12 Motor Rotation: Lets you make this change in the ESC so no
wires need to be changed between the ESC and the motor.
Programmable
Items
BasicItems
Programmable Value
Default Settings
1 2 3 4 5 6 7 8 9
1RunningMode
Forward with
Brake
Forward/Reverse with
Brake
Forward/
Reverse
2DragBrakeForce 0% 5% 10% 20% 40% 60% 80% 100%
3LowVoltage
Cutoff
non-portection 2.6V/Cell 2.8/Cell
3.0/
Cell
3.2/
Cell
3.4/
Cell
4StartMode Level1 Level2
Level
3
Level
4
Level
5
Level
6
Level
7
Level
8
Level
9
Advanced Items 1 2 3 4 5 6 7 8 9
5MaxBrakeForce 25% 50% 75% 100% disable
6MaxReverse
Force
25% 50% 75% 100%
7InitialBrakeForce
=DragBrake
Force
0% 20% 40%
8 Neutral Range 6%(Narrow) 9%(Normal) 12%(Wide)
9Timing 0.00º 3.75º 7.50º 11.25º 15.00º 18.75º 22.50º 26.25º
10ReservedItem
11ReservedItem
12MotorRotation Counterclockwise Clockwise
QUICK START GUIDE
The quick start setup guide will get you running quickly using the
ESC’s default settings.
1. Mount the ESC and motor in the car.
2. Connect the ESC to the motor.
3. ConnecttheESCreceiverleadtoCH2onyourreceiver.
4. Ensure the ESC switch is OFF.
5. Connect a fully charged battery.
6. Calibrate ESC to the transmitter.
MOUNTING THE SPEED CONTROL
Mount the ESC in the location specified by your vehicle’s instruction
manual. Use double-sided foam tape to secure the speed control in
position.
Ensure all wiring connections can be reached prior to
mounting.
Use double-sided foam tape to secure the switch to a convenient
location in the vehicle.
Receiver
Brushless
Motor / Speed
Control
CH1
CH2
Motor Battery
Steering
Servo
ON/OFF
SET
WIRING DIAGRAM
ESC LED STATUS
• NoESCLEDsshowalightwhenthereisnothrottleinputfromthe
transmitter.
• TheredESCLEDshowsalightwhenthereisanythrottleinput
from the transmitter.
• BoththeredandgreenLEDsglowatthefullforwardthrottle
position.
AUDIBLE WARNING TONES
1. Inputvoltage:TheESCcheckstheinputvoltagewhenitis
powered on. If a voltage problem is detected, the ESC continuously
sounds2beepswitha1secondpause(xx-xx-xx). Power off the
ESC and ensure the connections are secure and that the battery
power is not too low for safe operation.
2. Radioconnection:TheESCchecksradiosignalinputwhenitis
powered on. If a problem is detected, the ESC continuously sounds
1beepwitha2secondpause(x-x-x).PowerofftheESCand
ensure the radio system is operating correctly.
For sensorless brushless motors:
1. ConnecttheESCterminalA(typicallydesignatedbyabluewire)
to the motor’s terminal A (red wire on a Dynamite Fuze sensorless
motor).ThismayalsobechangedinProgrammingItem12,Motor
Rotation, without changing wire connections.
2. ConnecttheESCterminalB(typicallydesignatedbyayellowwire)
tothemotor’sterminalB(bluewireonaDynamiteFuzesensorless
motor).
3. ConnecttheESCterminalC(typicallydesignatedbyanorange
wire) to the motor’s terminal C (black wire on a Dynamite Fuze
sensorless motor).
NOTICE: Always disconnect the battery from the ESC when
you have finished operating your vehicle. The ESC’s switch only
controls power to the receiver and servos. The ESC will continue
to draw current when connected to the battery, resulting in
possible damage to the battery through over discharge.
ESC CALIBRATION PROCEDURE
Ensure proper ESC function by calibrating the ESC to your
transmitter inputs.
1. PowerofftheESC.
2. Ensureyourtransmitterispoweredon,throttleisnotreversed,
throttletrimisneutralandthrottletravelrangeisat100%.Disable
anyspecialfunctionssuchasABS,etc.
3. PresstheSETbuttonwhilepoweringontheESC.Releasethe
button as soon as the red LED starts to flash.
4. CalibratethethrottlepointsbypressingtheSETbuttononceafter
each step.
 •Neutralpoint(1ash)-leavethethrottleatrest,untouched
 •Fullthrottle(2ashes)-pullthethrottlefullyback
 •Fullbrakes/reverse(3ashes)-pushthethrottlefullyforward
5. Themotorwillrun3secondsafterthelaststepiscompleted.
Tip: If the motor turns in the wrong direction, reverse the
connectionofany2motorwires.
ESC FUNCTIONS AND MODES
The Fuze ESC includes programming options so you can adjust the
way your vehicle performs. Refer to the included settings table to
adjust the ESC for your driving conditions.
ESC PROGRAMMING PROCEDURE
Programming can be accomplished using the SET button on the on/
offswitchorDigitalProgramBox(DYNS3005).
PROGRAMMING THE ESC
1. ConnectabatterytotheESC.
2. PowerontheESCusingtheESCswitch.
3. HoldtheSETbuttonfor1seconduntilthegreenLEDblinks,then
release the SET button to enter programming mode.
4. PressandreleasetheSETbuttonasneededtogettothedesired
menuoption(theGreenLEDwillblinkcorrespondingtothemenu
itemnumber).Programmingmenuitems1through9areaccessible
usingtheSETbuttonontheESC.Programmingmenuitems10and
above are only accessible using the optional ESC programming
card.Programmingofmenuitems10and11isonlypossibleafter
firmware updates to the ESC programming card.
5. Whenatthedesiredmenuitem,presstheSETbuttonfor3
seconds until the red LED blinks.
6. PresstheSETbuttontomoveamongthesettingsbasedon
how many times the red LED blinks (Refer to the table for more
information).
7. SavethesettingbypressingtheSETbuttonfor3seconds.
8. Power off the ESC switch and repeat instructions above to change
other settings.
Tip: If desired, the ESC programming can be returned to default
settings by powering on the ESC switch and pressing the SET
buttonfor5seconds.
GEARING
This brushless motor does not have a commutator or brushes,
so it should not wear out. However, it can still be damaged by
overheating due to improper setup.
• Anytimeyoumodifyaparameteronthevehicle,checkthe
motor’s temperature. The recommended maximum motor
temperaturelimitis80°C(176°F).Overheatingcanburnthecoils
and/or melt solder joints inside the motor.
• Measuringthemotor’stemperatureistheonlysafewaytoknow
if the gear ratio is correct.
INSTALLING THE MOTOR
Always make sure the motor mounting screws are long enough to
properly seat into the motor. However, ensure the screws do not
enter into the motor too far, which could damage the motor. The
maximum depth that the motor mounting screws can enter into the
motorisapproximately1/8in(3mm).Wheninstallingthemotor
into your vehicle, it is very important that the gear mesh is correct
(smooth with no binding). The vehicle’s motor mounts usually
feature adjustable slotted mounting holes so you can adjust the
gear mesh properly.
Proper gear mesh (how gear teeth meet) is important to the
performance of the vehicle. When the gear mesh is too loose, the
spur gear could be damaged by the pinion gear of the motor. If the
mesh is too tight, speed could be limited and the motor and ESC
will overheat. To ensure proper gear mesh, insert a small piece of
paper in between the pinion and spur gear as you are installing
them. Push the gears together while tightening the motor screws.
Remove the small piece of paper by rotating the spur gear until
it comes out. Check the mesh at multiple points on the spur gear
before finalizing the motor mounting position.
TROUBLESHOOTING GUIDE
PROBLEM SOLUTION
System switch powered ON,
but no motor function and no
audible tone
Recharge or replace battery
Ensure all connections are secure
Repair or replace system switch or system
Ensure system programming for battery is correct for your battery
System switch powered ON, but
no motor function and system
continuouslysounds1beepbetween
2secondpauses
Ensure connections between system and receiver are secure
Ensure transmitter is bound to the receiver
Ensure receiver antenna is not damaged
System turns in the wrong direction This system is only compatible with vehicles that require a motor with a CCW rotation
System stops
When red system LED flashes, recharge or replace battery
When green LED flashes, let the system cool, changing set up or gearing to avoid overheating
Ensure system programming is correct for voltage and battery
Disconnect battery and let system cool
Ensure system programming is not causing overheating
Replace gearing
Ensure gearing is not causing overheating
System accelerates irregularly
Replace with a high-power battery
Replace battery
Replace damaged wiring
Adjust or replace gearing
System does not turn continuously in
response to throttle
Replace wiring or motor
Ensure good reception between transmitter and receiver
Replace system
Steering servo operates but the
system does not run
Ensure all system programming matches your installed systems requirements for safety
Ensure all receiver connections are correct and secure
Test the system apart from the vehicle system and replace system as needed
Recharge or replace batteries
Ensure all system connections are secure
Adjust throttle travel or other throttle settings on the transmitter and the system
Steering and system do not function
Ensure all connections to receiver are correct and secure
Refer to manufacturer’s instructions to repair or replace transmitter
Recharge or replace batteries
Vehicledoesnotoperateatfullspeed
Recharge or replace batteries
Ensure system programming is correct for voltage and battery
Adjust transmitter settings, such as trim, throttle travel, etc.
Ensure ESC settings are correct for system
Calibrate throttle control to system
System slows but will not stop
Adjust transmitter settings, such as trim, throttle travel, etc.
Ensure system settings are correct for system
Calibrate throttle control to system
Decreased transmitter range
Repair or replace system antennas
Repair or replace damaged motor, wiring and electrical parts
Move receiver or adjust antenna location so that no metal parts are between the antenna
and the transmitter
Recharge or replace batteries
Refer to receiver and transmitter manufacturer’s instructions to adjust reception or change
to a free and open radio frequency
WARRANTY AND SERVICE CONTACT INFORMATION
Country of Purchase Horizon Hobby Contact Information Address
United States of
America
Horizon Service Center
(Repairs and Repair Requests)
servicecenter.horizonhobby.com/
RequestForm/
4105FieldstoneRd
Champaign,Illinois,61822USA
Horizon Product Support
(Product Technical Assistance)
[e-mail]
877-504-0233
Sales
[e-mail]
800-338-4639
United Kingdom
Service/Parts/Sales:
Horizon Hobby Limited
[e-mail]
Units1–4,PloytersRd,StapleTye
Harlow,Essex,CM187NS,
United Kingdom
+44(0)1279641097
Germany
Horizon Technischer Service [e-mail]
Christian-Junge-Straße1
25337Elmshorn,Germany
Sales:HorizonHobbyGmbH +49(0)41212655100
France
Service/Parts/Sales:
Horizon Hobby SAS
[e-mail]
11RueGeorgesCharpak
77127Lieusaint,France
+33(0)160183490
COMPLIANCE INFORMATION FOR THE EUROPEAN UNION
EU Compliance Statement: Horizon Hobby, LLC hereby
declares that this product is in compliance with the essential
requirements and other relevant provisions of the EMC Directive.
A copy of the EU Declaration of Conformity is available online at:
http://www.horizonhobby.com/content/support-render-compliance.
Instructions for disposal of WEEE by users
in the European Union
This product must not be disposed of with other waste.
Instead, it is the user’s responsibility to dispose of their
waste equipment by handing it over to a designated
collections point for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of your waste
equipment at the time of disposal will help to conserve natural resources
and ensure that it is recycled in a manner that protects human health
and the environment. For more information about where you can drop
off your waste equipment for recycling, please contact your local city
office, your household waste disposal service or where you purchased
the product.
LIMITED WARRANTY
What this Warranty Covers
Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that
the product purchased (the “Product”) will be free from defects in
materials and workmanship at the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic
damage,(ii)damageduetoactsofGod,accident,misuse,abuse,
negligence, commercial use, or due to improper use, installation,
operation or maintenance, (iii) modification of or to any part of the
Product, (iv) attempted service by anyone other than a Horizon Hobby
authorized service center, (v) Product not purchased from an authorized
Horizon dealer, or (vi) Product not compliant with applicable technical
regulations or (vii) use that violates any applicable laws, rules, or
regulations.
OTHERTHANTHEEXPRESSWARRANTYABOVE,HORIZONMAKESNO
OTHERWARRANTYORREPRESENTATION,ANDHEREBYDISCLAIMS
ANYANDALLIMPLIEDWARRANTIES,INCLUDING,WITHOUT
LIMITATION,THEIMPLIEDWARRANTIESOFNON-INFRINGEMENT,
MERCHANTABILITYANDFITNESSFORAPARTICULARPURPOSE.THE
PURCHASERACKNOWLEDGESTHATTHEYALONEHAVEDETERMINED
THATTHEPRODUCTWILLSUITABLYMEETTHEREQUIREMENTSOF
THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive remedy
shall be that Horizon will, at its option, either (i) service, or (ii) replace,
any Product determined by Horizon to be defective. Horizon reserves
the right to inspect any and all Product(s) involved in a warranty
claim. Service or replacement decisions are at the sole discretion of
Horizon.Proofofpurchaseisrequiredforallwarrantyclaims.SERVICE
ORREPLACEMENTASPROVIDEDUNDERTHISWARRANTYISTHE
PURCHASER’SSOLEANDEXCLUSIVEREMEDY.
Limitation of Liability
HORIZONSHALLNOTBELIABLEFORSPECIAL,INDIRECT,INCIDENTAL
ORCONSEQUENTIALDAMAGES,LOSSOFPROFITSORPRODUCTION
ORCOMMERCIALLOSSINANYWAY,REGARDLESSOFWHETHER
SUCHCLAIMISBASEDINCONTRACT,WARRANTY,TORT,
NEGLIGENCE,STRICTLIABILITYORANYOTHERTHEORYOFLIABILITY,
EVENIFHORIZONHASBEENADVISEDOFTHEPOSSIBILITYOFSUCH
DAMAGES.Further,innoeventshalltheliabilityofHorizonexceedthe
individual price of the Product on which liability is asserted. As Horizon
has no control over use, setup, final assembly, modification or misuse,
no liability shall be assumed nor accepted for any resulting damage
orinjury.Bytheactofuse,setuporassembly,theuseracceptsall
resulting liability. If you as the purchaser or user are not prepared to
accept the liability associated with the use of the Product, purchaser is
advised to return the Product immediately in new and unused condition
to the place of purchase.
Law
These terms are governed by Illinois law (without regard to conflict
of law principals). This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state. Horizon
reserves the right to change or modify this warranty at any time
without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide
warranty support or service. Once assembly, setup or use of the Product
has been started, you must contact your local distributor or Horizon
directly. This will enable Horizon to better answer your questions
and service you in the event that you may need any assistance. For
questions or assistance, please visit our website at www.horizonhobby.
com, submit a Product Support Inquiry, or call the toll free telephone
number referenced in the Warranty and Service Contact Information
section to speak with a Product Support representative.
Inspection or Services
If this Product needs to be inspected or serviced and is compliant in the
country you live and use the Product in, please use the Horizon Online
Service Request submission process found on our website or call
Horizon to obtain a Return Merchandise Authorization (RMA) number.
Pack the Product securely using a shipping carton. Please note that
original boxes may be included, but are not designed to withstand the
rigors of shipping without additional protection. Ship via a carrier that
provides tracking and insurance for lost or damaged parcels, as Horizon
is not responsible for merchandise until it arrives and is accepted at
our facility. An Online Service Request is available at http://www.
horizonhobby.com/content/service-center_render-service-center. If you
do not have internet access, please contact Horizon Product Support
to obtain a RMA number along with instructions for submitting your
product for service. When calling Horizon, you will be asked to provide
your complete name, street address, email address and phone number
where you can be reached during business hours. When sending
product into Horizon, please include your RMA number, a list of the
included items, and a brief summary of the problem. A copy of your
originalsalesreceiptmustbeincludedforwarrantyconsideration.Be
sure your name, address, and RMA number are clearly written on the
outside of the shipping carton.
NOTICE: Do not ship Li-Po batteries to Horizon. If you have
any issue with a Li-Po battery, please contact the appropriate
Horizon Product Support office.
Warranty Requirements
For Warranty consideration, you must include your original sales receipt
verifying the proof-of-purchase date. Provided warranty conditions have
been met, your Product will be serviced or replaced free of charge.
Service or replacement decisions are at the sole discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty, service will
be completed and payment will be required without notification
or estimate of the expense unless the expense exceeds 50%
of the retail purchase cost.Bysubmittingtheitemforserviceyou
are agreeing to payment of the service without notification. Service
estimates are available upon request. You must include this request
with your item submitted for service. Non-warranty service estimates
will be billed a minimum of ½ hour of labor. In addition you will be
billed for return freight. Horizon accepts money orders and cashier’s
checks,aswellasVisa,MasterCard,AmericanExpress,andDiscover
cards.BysubmittinganyitemtoHorizonforservice,youareagreeing
to Horizon’s Terms and Conditions found on our website http://www.
horizonhobby.com/content/service-center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant
in the country of use and ownership. If received, a non-
compliant Product will not be serviced. Further, the sender
will be responsible for arranging return shipment of the
un-serviced Product, through a carrier of the sender’s choice
and at the sender’s expense. Horizon will hold non-compliant
Product for a period of 60 days from notification, after which
it will be discarded.
10/15
ESC SPECIFICATIONS
Type Sensorless
Constant/Peak 130A/760A
Resistance 0.0004Ohm
Function
Forward/Brake-Forward/BrakeReverse(for
Rock Crawler: Forward/Reverse)
Vehicle Type 1/8BuggyorTruggy,1/104WDShortCourse
Operation
Proportional forward, proportional reverse
with braking delay
Input Voltage 7.4V–14.8V
Motor Type
2SLi-Poupto6000Kv;3SLi-Poupto4000Kv;
4SLi-Poupto3000Kv
BEC Output 6V/3A
Overload Protection Thermal
Dimensions (LxWxH) 53.5mmx36mmx36mm
Weight 79g
MOTOR SPECIFICATIONS
RPM/V 1800RPM/V
Current 2.0A@7.2V
Dimensions (Dia. x L)
43.2x70mm(1.7x
2.76in)
Weight 354g(12.49oz)
Efficiency 90%
Poles 6
Power 2000W
Shaft Dimensions (Dia.
x L)
5x21.7mm(.20x.85in)
Voltage 7.4V–22V
Connector Type 4mmbullet