EAU corsair p Specification: lemDY8953 Instructional Manual WINGED mm mom oem so os 0 4270mm (50in} Overall Length 086mm (45.8in} Wing Loading: Belgium’ BE Sydney Battery: 14.8Y 2200méaAh Li-Po, 200 Speed Controller 404 Brush less Motor Size BMIT204-KVE00 Brush less Enquirer Flying Weights — mee oe me 1650g (48.
Safety Precautions $ Never fly the Airplane where there are crowds of people, power lines overhead, automobiles or near highways give yourself plenty of room for flying,as the plane can travel at a high rate of sped Remember you are responsible for the safety of others. € Do not fly in strong winds. #Do not attempt to catch the Airplane while flying. © Children under the age of 18 should not have admission to the transmitter for the plane.
How to use your dynamo 2.4G rc system ® important 1. Put down throttle sticker. 2. Turn on transmitter power-switch. 3. Please let your receiver connect with battery in 10 seconds. 4. Check your protect-switch, when protect-switch in up station, put down, release from protect. when protect-switch in down station, put up freest then put down again, release from protect,you can fly now .
RTF Including RIF including: u Fuselage & Wing e Elevator = Landing gear u Vertical stabilizer u Push rod u Propeller u Glue u Spinner e Decal u Li-Po battery (14.
Assembly Bl ao the foam glue on the interface of left and right wing, then glue them together. BE Glue the plastic part on the wing. B Locate the wing in place. BE Connect the aileron servos with Y wires. Be Connect the E-retract with Y wires. 3 Fix the wing with PM3xdsmm screw.
Assembly BE Fix the rear landing gear on fuselage with 1.5mm hex angular screwdriver. Bey the foam glue on the interface of horizontal stabilizer and vertical stabilizer, then glue them loather. EB Install elevator push rod as shown. 10} Install rudder push rod as shown. iB Install the scale antenna set with the glue. Install the propeller.
Stick Operation MODE 1 MODE 2 MOVEMENT THROTTLE et ELEVATOR a, AILERONS ironic! plane movement airplane action control plan movement airplane action airplane action Squadron movement * § 4 airplane action
CG And Receiver Assembling The ideal C.G. position is 85~80mm behind the leading edge measured at where the wing meets the fuselage. in order to obtain the C.G. specified, add weight to the fuselage or move the battery position. Check the C.G. before flying. le. 85-90mm 85-80mm Center of gravity Center of gravity Suggest Control Throw Setting Elevator Aileron Rudder Leads with silicon i ES C-40A | on ak cannonade 14.8V 2200maAh Li-Po 20C {] orn Propeller | 2.
Manual of Brush less Motor Speed Controller Specification) Chang Model Cont, | Burst | BEC | BEC | Battery Coll User Balminess | Weight Size Cu rent] Current | Mode | Output] Riles | NIGH | Program| Discharge TWH C108) | (Morel) Ti poly) Nig | shale | Protection 2A Be-12 124 | 15A | Sweet [VBA 24 | S12 | Awl] NA 19g 45%24%9 184 Flo-12 184A 22A | Wink {SVALBARD 24 512 | Cashless NA 15 45%24%11 BA E025 254 | 35A | with SVALBARD 24 | S12 | Available NA 21g 45%24%11 3A Es-30 nA 40A | Switch | SVALBARD 24 512 |
Manual of Brush less Motor Speed Controller ® fa special bore * 2 56717 is emitted after 2 beep tones (heap beep), means the ESC has entered the program made, iris because the throttle channel of your Transmitter is reversed, please sst it correctly; & if the very rapid "neap-beep-, beep-beep" tones is emitted, means the input voltage is too low or too high, please check your battery's voltage. 3.
Manual of Brush less Motor Speed Controller Somme! startup procedure: Move throttle | | Connect battery || goes hosp” tones | | When seatmate is | | Move throttle stick stick te puck to ESC, bat tarn and spacial tons like then switch "5123" means presenting the number “tone on transmitter, pesos supply is OK of lithium battery cells should be emitted should be emitted, | | finished, a long | | upwards to go fining ‘Chretien age Be bling: {Throttle range should be reset whenever a new transmitter Is being us
-how To Programming The ESC With The Dynamo Radio How to enter the programming mode of the Dynamo's brush less ESC with the Dynamo 2.4Ghz radio system: (Naming: Please disconnect the motor from the ESC before starting the following procedure) Tum on the transmitter, then connect battery to the receiver, let the normal auto binding process completed.