Instructions for Use
DYE-1004 40A ESC
ASSEMBLY:
Install the propeller.
1 2 3 4 5 6 7
8
9 10
11 12 13
15 16 17 18 19 20
14
Install the landing gear cover
with Double-sided tape.
16
17
16
17
Skytr
-15 Decal
DY-1007 9g Servo
DYR-2001 2.4G Receiver
DY-3003 Glue
SPARE PART LIST:
BM2815A-KV1100
Brushless Motor
BM2815A-KV1100-Shaft
Motor Shaft
DECAL:
Skytr-02 Wing Skytr
-04 Elevator
Skytr-03 Vertical Stabilizer
Skytr-09 Landing Gears
Skytr-07 Spinner
DY8938
Dynam RC
dynam-rc.cn
of
This product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Please recycle.
over
CENTER OF GRAVITY(C.G.)
DIRECTIONS FOR ASSEMBLY AND ADJUSTMENT
Wingspan
Length
Flying Weight
Wing Area
Wing Load
Radio System
Power
Battery
: 1280mm (50.4in)
: 1000mm (39in)
: 1000g (35.3oz)
: 23dm²
: 43.5g/dm²
: 4 Ch TX and 7 Ch RX
: Brushless System
: LIPO, 2200 mAh, 11.1V
Control Throw Setting Suggestion
Elevator Aileron Rudder
11.1V 2200mAh
Li-Po, 20C
(9060x3)
ESC-30A
ESC-40A
Lithium-polymer Battery
2200mAh 14.8V
20C Discharge
Rechargeable Cells
Use li-po charger only
MOTOR
DY-6006 11.1V 2200mAh
20C Battery
DYAT-008 Servo Horn
DY-3001 Quick-Controller
Skytr-01 Fuselage
Skytr-05 Wing Back Cowl
Skytr-06 Cowl
Skytr
-14 Bolt Pipe
Connect the pushrod on the rudder
and secure the screw (the servo
should be in the center position) .
Connect the pushrod on the elevator
and secure thescrew (the servo
should be in the center position) .
Connect the aileron servos
with the Y wires.
Connect the direction pushrod.
( The servo should be in center
position)
55 60
55 60
11
8
9
2
5
12
3
6
1
13
4
15
7
10
16
17
Slide the nose gear into the
slot on the bottom of the
fuselage.
Use a hexagon screwdriver to
tighten the screw.
Remove the tape from both
sides of the fuselage head.
Install the cowl .
Install the landing gear with
PA2.5*8mm screws.
Install the horizontal stabilizer
and vertical stabilizer.
Secure the stabilizers with
PA2.3*20mm screw.
Install the spinner with PA2*
6mm screws.
Apply glue on the antenna
and insert it into the main wing
as shown.
Apply glue on the contact area
of the left and right wing.
Glue the left and right main
wings together.
Secure the wing onto the
fuselage with PA2.3*20mm
screws.
Secure the wing struts with
PA 2.5*8mm screws.
Install the battery.
DYT-2002 4CH Transmitter
DY-3007 Flap hinges
Skytr-08 Plastic Part Set
Skytr-10 Canopy
Skytr-11 Push Rod
Skytr-12 Wing Struts
Skytr-13
Propeller
Skytr
-16
Plastic Tab
Skytr
-17
Screw set