User manual
Table Of Contents
- 1 Introduction
- 2 Controls, Indicators and Connections
- 2.1 Input Mono
- 2.2 Input Stereo
- 2.3 FX 1/2
- 2.4 AUX
- 2.5 MON
- 2.6 MASTER with GEQ
- 37 - USB 2.0 DIGITAL AUDIO INTERFACE
- 38 - MASTER LED-DISPLAY
- 39 - STANDBY
- 40 - MASTER L/R fader
- 41 - MASTER A OUT L/R
- 42 - POWER AMP INPUTS L/R
- 43 - MASTER B OUTPUTS L/R
- 44 - MASTER B
- 45 - PRE/POST of MASTER B
- 46 - STEREO/MONO of MASTER B
- 47 - PHONES
- 48 - PHONES
- 49 - REC SEND L/R
- 50 - REC SEND & USB OUT
- 51 - 9-BAND STEREO GRAPHIC EQUALIZER
- 2.7 DISPLAY with function keys
- 2.8 Stereo Power Amplifier
- 2.9 Rear panel
- 3 Display & functions
- 4 DIGITAL AUDIO INTERFACE
- 5 Setting up a standard PA
- 6 Master Patchbay and different setup alternatives
- 1 Einführung
- 2 Bedienelemente und Anschlüsse
- 2.1 Input Mono
- 2.2 Input Stereo
- 2.3 FX 1/2
- 2.4 AUX
- 2.5 MON
- 2.6 MASTER mit GEQ
- 37 - USB 2.0 DIGITAL AUDIO INTERFACE
- 38 - MASTER-Aussteuerungsanzeige
- 39 - STANDBY-Schalter
- 40 - MASTER L/R-Fader
- 41 - MASTER A OUT L/R-Buchsen
- 42 - POWER AMP INPUTS L/R-Buchsen
- 43 - MASTER B OUTPUTS L/R-Buchsen
- 44 - MASTER B-Regler
- 45 - PRE/POST-Schalter für MASTER B
- 46 - STEREO/MONO-Schalter für MASTER B
- 47 - PHONES-Buchse
- 48 - PHONES-Regler
- 49 - REC SEND L/R-Buchsen
- 50 - REC SEND & USB OUT-Regler
- 51 - 9-BAND STEREO GRAPHIC EQUALIZER
- 2.7 DISPLAY mit Funktions-Tasten
- 2.8 Stereo-Leistungsverstärker
- 2.9 Rückseite
- 56 - Netzbuchse
- Die Spannungsversorgung des PowerMate erfolgt ausschließlich mit dem mitgelieferten IEC-Netzkabel über eine verriegelnde Netzbuchse. Schließen Sie den PowerMate nur an eine geeignete Netzversorgung an, die den auf dem Typenschild angegebenen Anfor...
- 57 - Netzschalter (POWER)
- 58 - MIDI IN/OUT-Buchsen
- 59 - Speaker Outputs Right/Left
- 3 Display & Funktionen
- 4 DIGITAL AUDIO INTERFACE
- 5 Aufbau einer Standard-PA
- 6 Master Patchbay und verschiedene Aufbauversionen
- 7 Specifications
POWERMATE
3
38
6.5 Active 2-way stereo configuration
This example uses the internal power amplifier of the PowerMate to drive the HI/MID cabinets. The full-range signal is
fed via MASTER A OUT L/R to an active crossover, e. g. the DYNACORD DSP 260. The LO signal outputs of the crossover
are connected to an external power amplifier, driving the woofer cabinets. The signal of the crossover’s HI/MID-signal
outputs is fed back to the PowerMate’s internal power amplifier via POWER AMP INPUTS. Compared to the passive con-
figuration, the overall sound gains transparency and higher sound pressure levels are possible, since the HI/MID cabi-
nets do not have to deal with the low frequency signals.
Illustration 6-5: Active 2-way stereo configuration