User manual
Table Of Contents
- 1 Introduction
- 2 Controls, Indicators and Connections
- 2.1 Input Mono
- 2.2 Input Stereo
- 2.3 FX 1/2
- 2.4 AUX
- 2.5 MON
- 2.6 MASTER with GEQ
- 37 - USB 2.0 DIGITAL AUDIO INTERFACE
- 38 - MASTER LED-DISPLAY
- 39 - STANDBY
- 40 - MASTER L/R fader
- 41 - MASTER A OUT L/R
- 42 - POWER AMP INPUTS L/R
- 43 - MASTER B OUTPUTS L/R
- 44 - MASTER B
- 45 - PRE/POST of MASTER B
- 46 - STEREO/MONO of MASTER B
- 47 - PHONES
- 48 - PHONES
- 49 - REC SEND L/R
- 50 - REC SEND & USB OUT
- 51 - 9-BAND STEREO GRAPHIC EQUALIZER
- 2.7 DISPLAY with function keys
- 2.8 Stereo Power Amplifier
- 2.9 Rear panel
- 3 Display & functions
- 4 DIGITAL AUDIO INTERFACE
- 5 Setting up a standard PA
- 6 Master Patchbay and different setup alternatives
- 1 Einführung
- 2 Bedienelemente und Anschlüsse
- 2.1 Input Mono
- 2.2 Input Stereo
- 2.3 FX 1/2
- 2.4 AUX
- 2.5 MON
- 2.6 MASTER mit GEQ
- 37 - USB 2.0 DIGITAL AUDIO INTERFACE
- 38 - MASTER-Aussteuerungsanzeige
- 39 - STANDBY-Schalter
- 40 - MASTER L/R-Fader
- 41 - MASTER A OUT L/R-Buchsen
- 42 - POWER AMP INPUTS L/R-Buchsen
- 43 - MASTER B OUTPUTS L/R-Buchsen
- 44 - MASTER B-Regler
- 45 - PRE/POST-Schalter für MASTER B
- 46 - STEREO/MONO-Schalter für MASTER B
- 47 - PHONES-Buchse
- 48 - PHONES-Regler
- 49 - REC SEND L/R-Buchsen
- 50 - REC SEND & USB OUT-Regler
- 51 - 9-BAND STEREO GRAPHIC EQUALIZER
- 2.7 DISPLAY mit Funktions-Tasten
- 2.8 Stereo-Leistungsverstärker
- 2.9 Rückseite
- 56 - Netzbuchse
- Die Spannungsversorgung des PowerMate erfolgt ausschließlich mit dem mitgelieferten IEC-Netzkabel über eine verriegelnde Netzbuchse. Schließen Sie den PowerMate nur an eine geeignete Netzversorgung an, die den auf dem Typenschild angegebenen Anfor...
- 57 - Netzschalter (POWER)
- 58 - MIDI IN/OUT-Buchsen
- 59 - Speaker Outputs Right/Left
- 3 Display & Funktionen
- 4 DIGITAL AUDIO INTERFACE
- 5 Aufbau einer Standard-PA
- 6 Master Patchbay und verschiedene Aufbauversionen
- 7 Specifications
POWERMATE
3
15
2.4 AUX
Generally, the AUX channel is used for the connection of an additional, external FX unit. Depending on the setting of the
AUX 1/2 POST button, it is also possible to configure the bus for monitoring purposes. Additionally the AUX channel is
available at the DIGITAL AUDIO INTERFACE (channel USB 3).
30 - AUX SEND
This output provides connection for an external FX unit or, when used for monitoring, a power amplifier or active stage
monitor speaker systems. Using the AUX fader allows setting the output level in a wide range up to +20 dBu. The AUX
SEND is designed in Ground Sensing technology to prevent the induction of external noise, even with long cables. Use
balanced cables for the connection of external components whenever it is possible.
31 - AUX PRE/POST/
TO FX 2
The current mode of the AUX channel is indicated by this LEDs. Please refer to page page 25 for more details about the
available modes.
32 - MUTE
The MUTE button mutes the AUX output signal.
33 - AUX
FADER
This fader controls the summed audio signal at the AUX output. When used for monitoring, this fader lets you control
the volume of the monitor system. When using the DIGITAL AUDIO INTERFACE for recording this fader also controls the
volume of the sent channel USB 3. See page 15 for details about using the DIGITAL AUDIO INTERFACE.
2.5 MON
34 - MONITOR
This output provides connection for an power amplifier or active stage monitor speaker systems. The MONITOR output
is designed in Ground Sensing technology to prevent the induction of external noise, even with long cables. Use bal-
anced cables for the connection of external components whenever it is possible.
35 - MUTE
The MUTE button mutes the MON output signal.
36 - MON
FADER
This fader controls the summed audio signal at the MONITOR output. When using the DIGITAL AUDIO INTERFACE as
output, this fader also controls the volume of sent channels USB 4.
2.6 MASTER with GEQ
37 - USB 2.0 DIGITAL AUDIO INTERFACE
The USB interface of the PowerMate is a USB B (female) connector. Please refer to chapter “DIGITAL AUDIO INTER-
FACE” on page 29 for more details.