Integrated High Speed Dome Camera Outdoor Installation Guide Version 3.
Installation Guide Preface Information given in this manual was current when published. The company reserves the right to revise and improve its products. All specifications are subject to change without notice. Notice This manual provides installation information for the outdoor integrated high speed dome.
Installation Guide This symbol on the product or on its packaging indicates that this product shall not be treated as household waste in accordance with Directive 2002/96/EC. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By proper waste handling of this product you ensure that it has no negative consequences for the environment and human health, which could otherwise be caused if this product is thrown into the garbage bin.
Installation Guide Warnings and Cautions • Handle the camera carefully Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by improper handing or storage. • Installing electricity wiring carefully Ask qualified personnel of electrical wiring for the installation. Please note that input electricity to the unit is at tolerance of DC12V/AC24V ± 10%.
Installation Guide Table of Contents 1. 2. 3. Introduction................................................................................................................6 Standard Package Contents .....................................................................................7 Camera Setups and Cable Connections ..................................................................9 3.1 Preparations for Dome Camera Setups .......................................................................... 9 3.
Installation Guide 5.3 6. Signal Distribution ......................................................................................................... 48 System Integration ..................................................................................................49 6.1 Using Pelco Keyboard................................................................................................... 49 6.2 Using Philips Allegiant Keyboard...................................................................
Installation Guide 1. Introduction With weather resistant feature, the Integrated High Speed Dome Camera is applicable to outdoor installation. The dome camera supports one cabling for easy installation, and can be integrated with various digital surveillance products, such as DVRs, Control Keyboards, and accessories for a total surveillance solution. In addition, large set of built-in protocols provide connectivity to other surveillance systems.
Installation Guide 2. Standard Package Contents Before proceeding, please check the box contains the items listed here. If any item is missing or has defects, DO NOT install or operate the product and contact your dealer for assistance.
Installation Guide Network Model Dome Camera with Data Cable for Power Supply, Video, Audio and Alarm Outdoor Mount Kit (AC 24V) M3 Standard Screw (x1) Lubricant M3 Security Screw (x1) M5 Standard Screw (x1) Waterproof Rubber M5 Security Screw (x1) Security Torx Optical Cover 8 Quick Guide CD: Operation Manuals
Installation Guide 3. Camera Setups and Cable Connections Before installing or connecting the dome camera, please refer to this section and complete preparations for dome setups and various switch settings. 3.1 Preparations for Dome Camera Setups The following installation procedure is for the outdoor dome equipped with the sunshield housing. Please follow the steps below to complete dome housing installation. STEP 1 Unpack the Dome Camera’s package and take out the Dome Camera unit.
Installation Guide STEP 4 Attach the dome cover to the camera body. Before doing that, apply some lubricant on the cover’s water-proof rubber to make the installation process smoother. Note that the tiny protrusion on the dome cover must align with one of the four holes on the dome body. STEP 5 Gently pressure the dome cover downward with two hands on the side of it. DO NOT press the cover, as shown in the figure; this might cause damage to the camera body.
Installation Guide STEP 7 Set the switches located on the bottom of the dome body. Refer to section 3.2 Dome Camera Setups for detailed information about various switch setting.
Installation Guide 3.2 Dome Camera Setups Before connecting the Dome Camera to other devices of CCTV system, please complete the Dome Camera’s ID and communication switch settings. These switches are located on the bottom of the Dome Camera. 3.2.1 Switch/Connector Definition Please refer to the diagrams and tables accompanied with for use of each switch/connector.
Installation Guide 3.2.2 Communication Switch Setting Communication Switch SW 1 SW 2 RS-485 Setting SW 3 Termination SW 4 Line Lock SW 5 Factory Default Reset SW 6 Reserved RS-485 is the interface that communicates the dome camera and its control device; for this reason, the RS-485 setup of the dome and the control device must be the same. The RS-485 default setting is half-duplex (see the diagram follows).
Installation Guide 3.2.3 ID Setting Please change the analog Dome Camera’s ID if there is more than one Dome Camera on the same installation site. Use the switch to change your Speed Dome Camera’s ID by turning the arrow to the desired number respectively. For instance, if the camera’s ID is 123, the ID switch should be set as below. NOTE: No two Dome Cameras should be given the same ID, or communication conflict may occur.
Installation Guide 3.2.4 Camera Control Protocol Setting Define the protocol you are going to use basing on the devices of your surveillance system. Generally, use one protocol even the devices are provided from different manufacturers. Use the switch to set your camera control protocol and the baud rate. Refer to the table below and turn the arrow to choose a protocol for your Dome Camera. The table below shows various protocols with their matching switch numbers and baud rate. Switch No.
Installation Guide 3.3 Cables and Connections The Dome Camera is supplied with one integrated 22-pin Data Cable for connecting with the power, video, and RS-485/audio input & audio output cables. Please read the following sections thoroughly before making connections. 3.3.1 Cable Requirements For operation, the Integrated High Speed Dome Cameras require video, RS-485 and power cables as described below: • The video cable sends video signals to a remote viewing site.
Installation Guide NOTE: Be careful not to pull the cables improperly during installation. Additionally, it is suggested to fasten the cables after cable connection is completed. Furthermore, when wiring the AC 24V power cable, make sure the Ground wire is inserted into the mid-pin of the terminal block. Network Model The network Speed Dome Camera’s Data Cable is illustrated as follows. 3.3.
Installation Guide Analog Model The analog Dome Camera’s 22-pin connector definition is listed as below.
Installation Guide 3.3.4 RS-485 Connector Definition RS-485 is the interface that communicates the Dome Camera and its control device. Please connect the control keyboard to the Dome Camera through the terminal block. The recommended cables for RS-485 communication are CAT 5 cables; maximum cable length for over 24-gauge wire is 4000 feet (1219 meters). If the total cable length exceeds 4000 feet, using a repeater to maintain the signals is recommended.
Installation Guide Insert the terminal into the pin holes on the connector housing, with the hook outward, as indicated in the figure. To unlock the terminal, press the hook, as indicated in the figure, with a proper tool and pull it out gently. Connect the 22-pin connector to the Dome Camera. 3.3.6 Ethernet Cable Connection Connect one end of the CAT5 Ethernet cable to the RJ-45 connector of the network Speed Dome Camera, and the other end of the cable to the network switch or PC.
Installation Guide 4. Dome Camera Installation Basing on user’s installation environments, the Dome Camera can be installed on ceiling, on wall or on pole. In the following section, various Dome Camera’s installation accessories, installation methods and installation procedures will be described in detail. In addition, the next section will provide the Dome Camera’s dimensions for your reference before installation. 4.1 Dome Dimensions The Dome Camera’s dimensions are Ø172 x 302.5 mm (6.7x11.
Installation Guide 4.2 Optional Accessories Dome Camera Accessories Sunshield Height: 129.5 mm (5.05 inches); Diameter: 190 mm (7.48 inches); 0.15 kg (0.33 lbs) Transparent/Vandal Proof/Smoke Cover Diameter: 147 mm (5.8 inches) Security Screw Set (equipped with Vandal Proof Cover) Power Adapter 77H07-A1030 (Input: 100~115VAC/Output: 24VAC 72VA) 77H07-A2030 (Input: 220~230VAC/Output: 24VAC 72VA) NOTE: When wiring, make sure the G/Y wire (Ground) inserted into the mid-pin of the terminal block.
Installation Guide Mounting Accessories Standard Pendent Mount White; 348×104×138.6 mm (13.7×4.1×5.5 inches); 1.5 kg (3.3 lbs); Diameter: 45 mm (1.8 inches). Supplied with M8x12 screw x1, spring washer-8 x1, pendent tube washer x1, rubber washer-8 x1 and sponge x2. Compact Pendent Mount 184×104×115.2 mm (7.24×4.09×4.54 inches); 0.6 kg (1.2 lbs) Supplied with rubber washer-8 x1, pendent tube washer x1, spring washer-8 x1 and M8x12 screw x1. Straight Tube Iron, Height: 250/500 mm (9.8/19.
Installation Guide Swan Tube For mounting with Swan Tube. White; Iron, Dimension: 835 x 300 mm (32.9×11.8 inches); Diameter: 45 mm (1.8 inches); Weight: 3.8 kg (8.4 lbs); Supplied with pendent tube washer x1, rubber washer-8 x1, waterproof rubber x1, spring washer-8 x1 and M8x12 screw x1. Corner Plate Mini For mounting with Compact Pendent Mount. 270(L)×166(W)×95(D) mm (8.7×8×4.6 inches); Supplied with washer-8 x4, spring washer x4, M8x16 screw x4, M8 nut x4.
Installation Guide Pole Thin Direct Mounting 232(L)×136(W)×60(D) mm (9.1×5.4×2.4 inches); Diameter: 112~140 mm (4.4~5.5 inches); 0.7 kg (1.6 lbs). Supplied with stainless steel straps x4, M8x16 screw x4, washer x4 and spring washer-8 x4. Pole Wide Direct Mounting 270(L)×170(W)×60(D) mm (10.6×6.7×2.4 inches); Diameter: 112~130 mm (4.4~5 inches); 1 kg (2.2 lbs). Supplied with M8x16 screw x4, washer x4, stainless steel straps x4 and spring washer-8 x4. Corner Thin Box Mounting 300(L)×164(W)×222(D) mm (11.
Installation Guide Corner Wide Box Mounting 232(L)×234(W)×210(D) mm (9.1×9.2×8.3 inches); 2.7 kg (6 lbs); Supplied with M8x16 screw x4, washer-8 x4, and spring washer-8 x4. Power Box can be set inside the wide box. Pole Thin Box Mounting 291(L)×136(W)×242 (D) mm (11.5×5.4×9.5 inches); 3.1 kg (6.9 lbs); Supplied with M8x16 screw x4, washer-8 x4, spring washer x4 and stainless steel straps x4. Power Box can be set inside the thin box. Pole Wide Box Mounting 270(L)×166(W)×155(D) mm (10.6×6.5×6.1 inches); 3.
Installation Guide Wall Box Mounting 270(L)×166(W)×95(D) (10.6×6.5×3.7 inches); 2.2 kg (4.84 lbs); Supplied with M8x16 screw x4, washer-8 x4 and spring washer-8 x4. Power Box can be set inside the wall box. Stainless Steel Straps For fixing Pole Direct Mounting/ Pole Box on the pole. Length: 700 mm (27.5 inches); Width: 0.63”; 0.02 kg (0.04 lbs) Stainless Strap Cutter For tension, cut and crimp stainless steel straps. 1.4 kg (3.
Installation Guide Other Application Accessories Repeater/Converter D77R1: RS-485/RS-232 Converter D77R2: RS-232 between RS-485/RS-442 D77R3: Bi-phase to RS-485/RS-422 D77R1 D77R2 D77R3 Power Box 186.5×147 mm (7.3×5.8 inches); 2.6 kg (5.8 lbs) P1030 (Input: 110~115VAC/Output: 24VAC 72VA) P2030 (Input: 220~230VAC/Output: 24VAC 72VA) Signal Distribution Unit Relay control codes to speed dome cameras. Dimension: 432×44×90 mm (17×17.32×35.
Installation Guide 4.3 Ceiling Mounting with Straight Tube The Straight Tube is available in different length: 25 cm and 30 cm.
Installation Guide 6) Thread the cable(s) through the Outdoor Mount Kit and join the Outdoor Mount Kit to the Straight Tube with the supplied screws and washers. Then adjust the Waterproof Rubber to the joint. 7) Connect the cable(s) to the Dome Camera. 8) Join the Dome Camera to the Outdoor Mount Kit with the supplied M5 screw and washers.
Installation Guide 4.4 Wall Mount 4.4.1 Swan Tube Package Contents: • M8x12 Screw x1 • Spring Washer-8 x1 • Pendent Tube Washer x1 • Rubber Washer-8 x1 • Waterproof Rubber x1 Items Needed: • Dome Camera • Swan Tube and other equipped items (optional accessory) • • Waterproof Rubber (standard accessory) Screws and Screw Anchors for fixing the Swan Tube on the floor (not supplied). Tools Needed: • Tool for drilling • Tool for screwing Follow the steps to mount the dome with the Swan Tube.
Installation Guide Wall Mount: Swan Tube + Indoor Mounting Kit 4.4.
Installation Guide Tools Needed: • Tool for drilling • Tool for screwing Follow the steps below to mount the Dome Camera with the Compact Pendent Mount. 1) Make a cable entry hole on the wall to recess the cables. Otherwise, users could push up the Cable Entry Board on the Compact Pendent Mount’s Mounting Plate to place the cables, as shown in the photo below. Mounting Plate Cable Entry Board 2) Fix the Compact Pendent Mount on the wall with proper screws and screw anchors.
Installation Guide 6) Connect the cable(s) to the Dome Camera. 7) Join the Dome Camera to the Outdoor Mount Kit with the supplied M5 screw and washers. Wall Mounting: Compact Pendent Mount + Outdoor Mount Kit 4.4.
Installation Guide Tools Needed: • Tool for drilling • Tool for screwing Follow the steps below to mount the Dome Camera with the Standard Pendent Mount. 1) Make a cable entry hole on the wall to recess the cables. Otherwise, users could push up the cable entry board on the Standard Pendent Mount’s mounting plate to place the cables (see the illustration in section 4.4.2 Compact Pendent Mount > Step 1). 2) Fix the Standard Pendent Mount on the wall with proper screws and screw anchors.
Installation Guide Wall Mounting: Standard Pendent Mount + Outdoor Mount Kit 4.4.
Installation Guide Follow the steps to mount the Dome Camera with the Standard/ Compact Pendent Mount and Wall Box Mounting. 1) Make a cable entry hole on the wall to recess the cable(s). 2) Fix the Wall Box Mounting on the wall with proper screws and screw anchors. Then run the cable(s) through the hole on the Wall Box Mounting with the Data Cable’s 22-pin cable coming out. 3) Fasten the Standard/ Compact Pendent Mount onto the Wall Box Mounting with the supplied screws and washers.
Installation Guide 4.5 Corner Mount 4.5.
Installation Guide NOTE: Please block the cable entry hole with the supplied sponge to avoid insects entering the Pendent Mount. See the illustrations in section 4.4.2 Compact Pendent Mount > Step 4. 4) Attach the Waterproof Rubber to the Standard/ Compact Pendent Mount. 5) Thread the cable(s) through the Outdoor Mount Kit and join the Outdoor Mount Kit to the Standard/ Compact Pendent Mount with the supplied screws and washers. Then adjust the Waterproof Rubber to the joint.
Installation Guide 4.5.
Installation Guide 4) Attach the Waterproof Rubber to the Standard/ Compact Pendent Mount. 5) Thread the cable(s) through the Outdoor Mount Kit and join the Outdoor Mount Kit to the Standard/ Compact Pendent Mount with the supplied screws and washers. Then adjust the Waterproof Rubber to the joint. 6) Connect the cable(s) to the Dome Camera. 7) Join the Dome Camera to the Outdoor Mount Kit with the supplied M5 screw and washers.
Installation Guide 4.6 Pole Mount 4.6.
Installation Guide NOTE: Please block the cable entry hole with the supplied sponge to avoid insects entering the Pendent Mount. See the illustrations in section 4.4.2 Compact Pendent Mount > Step 4. 4) Attach the Waterproof Rubber to the Standard/ Compact Pendent Mount. 5) Thread the cable(s) through the Outdoor Mount Kit and join the Outdoor Mount Kit to the Standard/ Compact Pendent Mount with the supplied screws and washers. Then adjust the Waterproof Rubber to the joint.
Installation Guide 4.6.
Installation Guide 4) Attach the Waterproof Rubber to the Standard/ Compact Pendent Mount. 5) Thread the cable(s) through the Outdoor Mount Kit and join the Outdoor Mount Kit to the Standard/ Compact Pendent Mount with the supplied screws and washers. Then adjust the Waterproof Rubber to the joint. 6) Connect the cable(s) to the Dome Camera. 7) Join the Dome Camera to the Outdoor Mount Kit with the supplied M5 screw and washers.
Installation Guide 5. System Expansion 5.1 Connecting with Power Box A power box contains a 24V AC adapter, two terminal blocks (for communication and power) and one alarm board. With an IP66 case, the Power Box is ideal for outdoor installation environment. Two models are available: 100~115V AC power input (P1030) and 220~230V AC (P2030).
Installation Guide 5.2 Data Formats Transforming To integrate other surveillance devices with the high speed dome cameras or to extend the distance of communications, users could employ three kinds of repeater/converter, as shown below. With the advanced circuit design, these repeaters/converters offer 1KVrms isolation voltage and surge protection capability. The exiting network can be protected by the repeaters/converters. Up to 10 devices are allowed to connect to one repeater/converter.
Installation Guide 5.3 Signal Distribution The RS-485 Signal Distribution Unit (SDU) is designed to relay control codes to speed dome cameras. It is capable of communicating with cameras up to 1.0 kilometers away. Additionally, the SDU can be installed in either “star” or “daisy chain” configuration with up to 160 cameras (see the diagrams below). Its versatile installation configuration makes an easy integration into expanding surveillance systems.
Installation Guide 6. System Integration The dome camera is allowed to be integrated into other suppliers' surveillance systems with large set of built-in protocols. Refer to the following sections for more information. 6.1 Using Pelco Keyboard The speed dome camera can be controlled through a Pelco keyboard which built in with D protocol and P protocol. Please follow the instruction to manipulate our speed dome by a keyboard with D and P protocols.
Installation Guide Cable Definition (D Protocol Keyboard to PTZ Camera) Tx - 6 Tx+ 5 GND 4 1 Tx+ 2 3 GND GND 3 Rx - 2 Rx+ 1 4 Rx+ 5 Rx6 Tx- For D Protocol Keyboard 6.2 For SpeedDome Using Philips Allegiant Keyboard The dome cameras can be integrated into Philips Allegiant systems through D77R3 repeaters. Please follow the instructions to control dome cameras through Philips Allegiant systems. Symbol Definition Command dome cameras to go to specific preset position.
Installation Guide Appendix A: Technical Specification Items G Model M Model V Model P Model T Model 1/4" EXview 1/4" CCD 1/4" EXview 1/4" CCD 1/4" EXview - Yes - Yes - 18× 23x 26× 35x 36x 540 TVL 530 TVL CAMERA CCD Sensor Progressive Scan Optical Zoom 1× ~ 12× variable Digital Zoom Effective NTSC 380k Pixels PAL 440k Horizontal Resolution 530 TVL 540 TVL 530 TVL Scanning System NTSC / PAL Synchronization Internal / Line Lock 1.
Installation Guide Items G Model M Model P Model T Model 8 24 8 Cruise Privacy Mask V Model 24 8 24 On / Off (Pan and tilt speed proportional to zoom ratio) Proportional Pan & Tilt Resume after Yes Power loss 16 Zone Title Preset, Sequence, Auto pan, Cruise Home Function Digital / Mechanical / Off Auto Flip On / Off On / Off On / Off On / Off On / Off - - - On / Off - Motion Detection On / Off On / Off On / Off On / Off On / Off Wide Dynamic Range On / Off On / Off On
Installation Guide Items S3 Model S4 Model S5 Model S6 Model CAMERA Sony CCD CCD Sensor 30× Optical Zoom 36× 1~12x variable Digital Zoom NTSC 380k 480k 380k 480k PAL 440k 570k 440k 570k 540 TVL 650 TVL 540 TVL 650 TVL Effective Pixels Horizontal Resolution Scanning System NTSC / PAL Synchronization Internal / Line Lock 1.0 Vp-p / 75 Ω, BNC Video Output > 50 dB (AGC Off) S/N Ratio Minimum Illumination Focal Length 0.1 lux; 0.01 lux (B/W) 0.1 lux; 0.01 lux (B/W) 3.
Installation Guide Items S3 Model S4 Model S5 Model S6 Model Mechanical / Digital / Off Auto Flip Digital Slow Shutter On / Off Motion Detection On / Off Wide Dynamic Range On / Off Day/Night: IR Cut Filter Auto / Manual Image Freeze On / Off Image Inverse On / Off 2D On / Off 3D On / Off Noise Reduction Alarm Input 8 Alarm Output 1 Alarm Reaction Preset, Sequence, Auto pan, Cruise GENERAL Environment Outdoor Controller Interface RS-485 Operating Temperature Waterproof Standa
