Owners Manual

17
17
DRAWING
NUMBER
1
2
3
3-1
4
4-1
5
6
7
8
8-1
9
9-1
10
10-1
11
12
12-1
13
14
14-1
15
16
17
18
19
20
21
22
22-1
23
24
FUEL CAP
HINGE SPRING
DOOR(RMC-55R7)
DOOR(RMC-55R7B)
TOP PLATE(RMC-55R7)
TOP PLATE(RMC-55R7B)
CARTRIDGE TANK
BAFFLE ASS'Y
VERTICAL REFLECTOR
BOTTOM REFLECTOR
CABINET HANDLE(RMC-55R7)
CABINET HANDLE(RMC-55R7B)
CABINET(RMC-55R7)
CABINET(RMC-55R7B)
FUEL INDICATOR WINDOW(RMC-55R7)
FUEL INDICATOR WINDOW(RMC-55R7B)
TOP FRONT PANEL
FRONT PANEL
(RMC-55R7)
FRONT PANEL (RMC-55R7B)
WICK HOLDER GASKET
BATTERY CASE ASS'Y(RMC-55R7)
BATTERY CASE ASS'Y(RMC-55R7B)
TANK HOLDER
BURNER TANK ASS'Y
DRIP TRAY ASS'Y
BURNER ASS'Y
GRILLE
WIND COVER
IGNITION COIL
SAFETY SHUTIOFF DEVICE(RMC-55R7)
SAFETY SHUTIOFF DEVICE(RMC-55R7B)
IGNITER ASS'Y
WICK ADJUSTER (RMC-55R7)
(COMPLETE)
WS-CT01R
WS-CT02R
WS-CT03R
WS-CT03RB
WS-CT04R
WS-CT04RB
WS-CT05R-1
WS-CT06R
WS-CT07R
WS-CT08R
WS-CT08RB
WS-CT09R
WS-CT09RB
WS-CT10R
WS-CT10RB
WS-CT37R
WS-CT12R
WS-CT12RB
WS-CT13R
WS-CT14R
WS-CT14RB
WS-CT15R
WS-CT16R
WS-CT17R-1
WS-CT18R
WS-CT19R
WS-CT20R
WS-CT21R
See 24
See 24-1
WS-CT23R-1
2123-0030-00
24-1
WICK ADJUSTER (RMC-55R7B)
(COMPLETE)
2123-0031-00
25
25-1
26
27
28
29
30
31
32
33
34
WICK ADJUSTER KNOB(RMC-55R7)
WICK ADJUSTER KNOB(RMC-55R7B)
WICK HOLDER
WICK
WING NUT
TOP DRAFT TUBE A
GLASS CYLINDER
BOTTOM INSULATOR ASS'Y
TOP INSULATOR
WALL GUARD
CARTRIDGE TANK ASS'Y
WS-CT25R
WS-CT25RB
WS-CT26R
See Specs
Below
WS-CT28R
WS-CT29R
WS-CT30R
WS-CT31R
WS-CT32R
WS-CT33R-1
WS-CT34R
DESCRIPTION
PART
NUMBER
PARTS LIST
SPECIFICATIONS
Model No.
Type of Heater
Heat Output
Fuel Tank
Tank Capacity
Continuous Combustion Time
Max. Fuel Combustion
Ignition Method
Dimensions
Max. Wick Height
Replacement Wick Number
U.L. Listed
RMC-55R7/RMC-55R7B
Radiant Reflection
Max. 10,000 BTU/hr
Cartridge
1.0 U.S. Gallon
Approx.11-14 hr.
0.07 U.S. gallons/hr
Battery-D Cell
2
19.3 inches
22.3 inches
11.9 inches
5/16
(8mm)
Pick-A-Wick-PW27, Kero-World
20401-U, Dura Heat DH-200
Glowick 200-B
Yes
Height
Width
Depth
REPAIR OF DAMAGED OR LEAKING
CARTRIDGE TANK ASSEMBLY MUST
BE DONE BY A FACTORY
AUTHORIZED SERVICE STATION.
EXPLODED PARTS DRAWING
NOTE: SPECIFY MODEL NUMBER AND
PART NUMBER WHEN ORDERING PARTS.