VERTICAL GAS SMOKER MODEL #DGY784BDP/DGY784BDP-D Français Français p. p. 28 XX Español p. p. 55 XX Español ATTACH YOUR RECEIPT HERE Serial Number Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-447-4768, 8:00 a.m. – 4:30 p.m. CST, Monday – Friday or email customerservice@ghpgroupinc.com. 70-10-541 1 Rev.
DYNA-GLO® VERTICAL GAS SMOKER STOP! 2
TABLE OF CONTENTS Safety Information ......................................................................................................................... 4 Package Contents ......................................................................................................................... 7 Hardware Contents ....................................................................................................................... 8 Preparation ..........................................................
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. If you have any questions regarding the product, please call customer service at 1-877-447-4768, 8:00 a.m. – 4:30 p.m. CST, Monday – Friday.
SAFETY INFORMATION • DO NOT store and use this appliance near gasoline or other combustible liquids or where other combustible vapors may be present. • DO NOT use this appliance as a heater. • DO NOT leave the appliance unattended while in use. Keep children and pets away from the appliance at all times. • NEVER close the damper completely while cooking.
SAFETY INFORMATION • Do not use the smoker if the burner fails to light or fails to remain lit. Under such conditions, gas should be turned off and the fuel cylinder should be disconnected. • Use in high wind conditions that result in poor burner operation such as blowing out and flaring should be avoided. If repositioning the appliance does not improve operation under such wind conditions, the appliance should be turned off.
PACKAGE CONTENTS L J Q H I J Q M F P G E D P C K K B O N A PART A B C D E F G H I DESCRIPTION Leg Burner & Control Unit Wood Chip Box Wood Chip Box Lid Water Bowl Cooking Grate Door Locking Bracket Smoke Stack Smoker Body QUANTITY PART DESCRIPTION QUANTITY 4 1 1 1 1 4 2 1 1 J K L M N O P Q Lifting Handle Side Damper Temperature Gauge Upper Door “AAA” Battery (1.
HARDWARE CONTENTS (shown actual size) AA BB CC DD M6x12 Screw M6x12 Shoulder Screw Spring Clip M6 Nut Qty. 32 Qty. 8 Qty. 2 Qty. 8 PREPARATION Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents above. If any part is missing or damaged, do not attempt to assemble the product. Contact customer service for replacement parts.
ASSEMBLY INSTRUCTIONS 1. Attach the legs. Align one leg (A) with mounting holes on the bottom of the smoker body (I). Thread screws through holes from outside of unit. Nuts are pre-welded to the cabinet. Repeat for other 3 legs (A). Tighten all screws (AA) with a Phillips screwdriver. 1 A AA I Hardware Used AA M6x12 Screw x12 2. Attach the burner and control unit. Open the bottom door of the smoker body (I).
ASSEMBLY INSTRUCTIONS 3. Attach the smoke stack. CAUTION: This unit is HEAVY! Do not attempt this step without assistance! Close the two doors. With the assistance of a helper, stand the unit upright on its legs on a firm and level surface. (Make sure that the burner/control unit and legs are attached). Open the upper door. Position the smoke stack (H) with control arm to the left as shown. Attach the smoke stack (H) by using 4 screws (AA). Securely tighten with a Phillips screwdriver.
ASSEMBLY INSTRUCTIONS 5. Attach the lifting handles. Insert 4 screws (AA) through the mounting holes on one of the lifting handles (J) and into holes on right side of smoker body (I). Use a Phillips screwdriver to secure the handles to the smoker body. Repeat on left side. 5 I J Hardware Used AA M6x12 Screw x8 6. Attach the side dampers. Dampers (K) are installed from the inside of smoker body (I). Thread the damper handle through the back hole of the side damper slots.
ASSEMBLY INSTRUCTIONS 7. Attach the door locking brackets. Align the door locking bracket (G) holes with the holes on the upper right side of the smoker body (I). Note: slots on the brackets (G) must be facing up. Thread 2 screws (AA) through the holes in the door locking bracket and into the threaded holes of the smoker body (I). Tighten the screws (AA) using a Phillips screwdriver. Repeat on lower right side. 7 I G AA Hardware Used AA M6x12 Screw x4 8. Attach the door handles.
ASSEMBLY INSTRUCTIONS 10. Install the water bowl. Slide the water bowl (E) onto the cooking grate supports inside the smoker body above the wood chip box as shown. 11. Install the cooking grates. Slide the 4 cooking grates (F) onto the top cooking grate supports inside the smoker body (I). 12. Mount the temperature gauge assembly. Insert the probe of the temperature gauge (L) through the middle hole of the smoker door from the outside. Secure with pre-assembled nut from inside panel using wrench.
ASSEMBLY INSTRUCTIONS 13. To install the “AAA” battery (N), remove the igniter button by turning it counterclockwise and inserting the “AAA” battery (N) with the positive end facing out. Reinstall the ingniter button by turning it clockwise and hand tightening. 13 N OPERATION INSTRUCTIONS CONNECTING THE LP TANK WARNING! ALL INSTRUCTIONS AND SAFEGUARDS ON THIS PAGE MUST BE FOLLOWED TO PREVENT FIRE, DAMAGE AND/OR INJURY. 1. The knob on the LP tank must be closed.
REPLACEMENT PARTS LIST For replacement parts, call our customer service department at 1-877-447-4768, 8:00 a.m. – 4:30 p.m. CST, Monday – Friday. PART DESCRIPTION 1 2 PART # Leg Burner and Control Unit - includes burner box, cast iron burner, burner support bracket, LP gas hose and regulator assembly, control panel, knob bezel.
