014 D M S E R I E S O W N E R ’ S M A N U A L W W W . D Y E P A I N T B A L L . C O M TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS AND GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . PAGE 02 QUICK REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PAGE 04 BOARD SETTINGS AND FUNCTIONS . . . . . . . . . . . . .
W A R N I N G IMPORTANT SAFETY INSTRUCTIONS AND GUIDELINES • The 2014 DM Series marker is not a toy. Misuse may cause serious injury or death. • Please read, understand and follow the directions in the 2014 DM Series owner’s manual. • Eye protection that is designed specifically for paintball and meets ASTM/CE standards must be worn by user and persons within range. • Recommend 18 years or older to purchase. Persons under 18 must have adult supervision.
QUICK REFERENCE QUICK REFERENCE USING YOUR MARKER USING YOUR MARKER AIR SUPPLY LPR - LOW PRESSURE REGULATOR The 2014 DM Series should be operated using air/nitrogen gas only. This air needs to be supplied to the Hyper4™ in-line regulator at a regulated pressure of no more than 850 psi. The Hyper4™ in-line regulator comes factory preset at approximately 145psi.
2014 DM SERIES BOARD 2014 DM SERIES BOARD SETTINGS AND FUNCTIONS SETTINGS AND FUNCTIONS TURNING THE 2014 DM SERIES ON AND OFF BLUE RED To turn on the 2014 DM Series, press and hold the power button for 3 seconds (see figure 1) until the LED’s turn blue. The blue light indicates board boot up. After the boot up sequence, the LED’s will turn either RED (no ball) or GREEN (ball ready to fire). To turn the 2014 DM Series off, press and hold the power button until the LED’s turn off.
2014 DM SERIES BOARD 2014 DM SERIES BOARD SETTINGS AND FUNCTIONS SETTINGS AND FUNCTIONS BOARD SETTINGS AND CONFIGURATION MODE FIGURE 1 There are five settings you can alter on the 2014 DM Series board with the DIP switches inside the grip frame (see figure 1): ABS Anti Bolt Stick. Trigger Sensitivity This setting adjusts the delay between two trigger pulls. Dwell This is the amount of time the solenoid is activated. Rate Of Fire This setting adjusts the maximum rate of fire.
2014 DM SERIES BOARD 2014 DM SERIES BOARD SETTINGS AND FUNCTIONS Blue - Rate Of Fire (ROF) 1 Values 1 - 45 (factory default 12.5 bps) The ROF setting is used to set the maximum rate of fire of the 2014 DM Series. The values do not correspond directly to a certain Balls Per Second (BPS) value. You will need to use the table below to locate your desired maximum ROF setting. The factory setting is 20 (12.5 bps). 9.80 BPS 10 10.75 BPS 19 12.34 BPS 28 13.88 BPS 37 15.87 BPS 2 9.90 BPS 11 10.
REACH AIRPORT - FEEDNECK ULTRALITE FRAME REACH AIRPORT REMOVING ULTRALITE FRAME FROM THE 2014 DM SERIES The 2014 DM Series comes equipped with a Reach Airport attached to the bottom of the frame. To turn on the gas supply, rotate the side lever counter clockwise until the internal stop is reached. To turn off the gas supply, rotate the side lever clockwise until the other stop is reached.
STICKY GRIP STICKY GRIP GRIP REMOVAL GRIP REMOVAL 2. While pulling with your thumb, using your index finger, to push the grips toward you. 1. Pull the upper back corner of the grips away from the gripframe with your thumb. Allowing the rear tabs to clear the frame. 4. Grab a hold of the inside of the grips with your fingers, using your palm on the outside surface of the grip. 3. The top portion of the grips should be free from the gripframe. 14 5. Pull the grip forward and down 6.
REACH TRIGGER ADJUSTMENT REACH TRIGGER ADJUSTMENT ADJUSTING YOUR REACH TRIGGER FIGURE 1 ULTRALITE REACH TRIGGER FIGURE 2 The trigger’s forward and over travel, spring tension, and reach are fully adjustable so that you can finetune the trigger to your preference. You do not need to remove the frame or grip from the gun in order to adjust the trigger pull. There are two adjustment screws located on the left side of the Ultralite frame and one adjustment screw behind the trigger.
FUSE™ BOLT FUSE™ BOLT ASSEMBLY AND MAINTENANCE ASSEMBLY AND MAINTENANCE 2 5 4 3 6 1 FUSE™ BOLT OPERATION To achieve top performance from your 2014 DM Series, it is important to understand the basic operation of the 2014 DM Series’ patented FUSE™ bolt system. BACK POSITION This design consists of three sleeves threaded together to capture the only moving part of the system, the bolt.
FUSE™ BOLT FUSE™ BOLT ASSEMBLY AND MAINTENANCE ASSEMBLY AND MAINTENANCE BOLT MAINTENANCE Regular Fuse™ bolt maintenance is vital to the performance of the 2014 DM Series. If the Fuse™ bolt is not kept well greased and the O-rings in good shape, the performance of the 2014 DM Series will be greatly hindered. To remove the bolt, Grab the bolt back cap with your right hand. Push the bolt release button, located on the left side of the bolt back cap, with your thumb.
LPR (LOW PRESSURE REGULATOR) LPR (LOW PRESSURE REGULATOR) ADJUSTMENTS AND MAINTENANCE ADJUSTMENTS AND MAINTENANCE LPR ASSEMBLY, CLEANING, TESTING AND CHANGING SEALS The LPR has six components and seven seals 1 Piston O-ring (012 BN70) 2 Piston 3 Shim stack (2 Lg, 9 sm) 4 LPR Cartridge 5 Body O-rings (3 pcs, 013 BN70) 6 Body internal O-ring (007 UR90) The Low-Pressure Regulator (LPR) is located at the front of the 2014 DM Series under the barrel (see page 24).
LPR (LOW PRESSURE REGULATOR) LPR (LOW PRESSURE REGULATOR) ADJUSTMENTS AND MAINTENANCE ADJUSTMENTS AND MAINTENANCE The LPR is housed in a self-contained cartridge. A fouled LPR cartridge can be quickly removed for service. The only user-serviceable part in the LPR is the regulator Seat, located in the Seat Retainer. This seal needs to be changed in the unlikely case the LPR is allowing gas through the regulator, increasing pressure sent to the solenoid.
HYPER4™ GAS THRU REGULATOR ADJUSTMENTS AND MAINTENANCE 015 BN 70 014 BN 70 007 UR 90 ATTACHMENT PISTON SCREW BODY HYPER4™ GAS THRU REGULATOR 007 UR 90 010 BN 70 CARTRIDGE SHIM STACK SEAT RETAINER ()()()()()() 4-40x1/8” RETAINING SCREWS BASIC VELOCITY ADJUSTMENT (see page 5, Quick Reference) ADVANCED ADJUSTMENTS The Hyper4™ regulator is adjusted in the same manner as the LPR (outlined on page 22). With the seat retainer screwed completely in the Hyper4™ will be set to approximately 10 psi.
ANTI CHOP EYES/ BALL DETENTS ANTI CHOP EYES/ BALL DETENTS MAINTENANCE AND CHANGING MAINTENANCE AND CHANGING ANTI CHOP EYES CHANGING BALL DETENTS The Anti Chop Eye (ACE) system will help prevent the 2014 DM Series from chopping paint by preventing fire of the marker until a ball is fully seated in front of the bolt. The eyes use a light beam across the breech. On one side there is a transmitter, and on the opposite side a receiver.
REACH AIRPORT DETAIL REACH AIRPORT DETAIL REMOVE PIN-HOUSING ASSEMBLY To disassemble the Reach Airport use the airport tool included on the DYE Multi-Tool. However, a pair of needle-nose pliers can be used to unscrew the Pin Housing. Just take care to not scratch or damage the threads or Pin Housing. • • Insert the airport tool into the Pin Housing and turn counterclockwise 3-4 revolutions. Note that the airport lever must be in the OFF position for the tool to grab the housing.
TROUBLE SHOOTING GUIDE AIR LEAKS AIR LEAKING BETWEEN BODY AND FRAME • • • • • • • AIR LEAKING FROM THE BACK OF AIRPORT • Check the O-ring on the Air system. If needed change the O-ring and try again. The O-ring normally used is #015 but some manufacturers might use a different size. Consult the manual of the air system you are using.
TROUBLE SHOOTING GUIDE PROBLEMS WITH ELECTRONICS SOLENOID WILL NOT ACTIVATE / TRIGGER NOT WORKING 2014 DM SERIES WON’T TURN ON • Check that the trigger adjustment is not set so that the micro switch cannot activate. You should hear a small click when pulling the trigger. • If the 2014 DM Series fires once when turned on but not after that, your trigger is set so that the micro switch is always activated. Re-adjust the trigger. • Change the battery if not positive about it’s charge.
EXPLODED VIEW 2014 DM SERIES WARRANTY WARRANTY AND LEGAL INFORMATION 1 4 8 WARRANTY DYE Precision, Inc. warrants for one year to the initial retail purchaser, from the initial date of purchase, that the paintball marker and regulator are free from defects in materials and workmanship, subject to the requirements, disclaimers and limitations of this warranty. Disposable parts, normal maintenance and standard wear and tear parts such as batteries, O-rings and seals are not warrantied.
